2-（Dinitromethylene）-1,3-diazacycloheptane （DNDH） was prepared by the reaction of 1,1-diamino-2,2-dinitro- ethylene （FOX-7） with 1,4-diaminoethane in NMP. Thermal decomposition behavior of DNDH was studied under...2-（Dinitromethylene）-1,3-diazacycloheptane （DNDH） was prepared by the reaction of 1,1-diamino-2,2-dinitro- ethylene （FOX-7） with 1,4-diaminoethane in NMP. Thermal decomposition behavior of DNDH was studied under the non-isothermal conditions with DSC method, and presents only one intensely exothermic decomposition process The kinetic equation of the decomposition reaction is da/dT= 103388× 3a2/3exp（--3.353 ×10^5/RT）/fl. The critical temperature of thermal explosion is 215.97℃. Specific heat capacity of DNDH was studied with micro-DSC method and theoretical calculation method, and the molar heat capacity is 215.40 Jomol-1,K-1 at 298.15 K. Adiabatic time-to-explosion was calculated to be 92.07 s. DNDH has same thermal stability to FOX-7.展开更多
The influence of thermal treatment on the lux-ampere characteristics of polycrystalline films from the CdSe<sub>x</sub>S<sub>1-x</sub> solid solution obtained by the method of thermal evaporati...The influence of thermal treatment on the lux-ampere characteristics of polycrystalline films from the CdSe<sub>x</sub>S<sub>1-x</sub> solid solution obtained by the method of thermal evaporation in a vacuum has been investigated. It is shown that at low illumination intensities L μ of electrons increases with a power law μ ~ L<sup>γ</sup>, first with the exponent γ > 1, then with γ ≈ 0.5, and their concentration n almost does not change. Starting from the intensity L > 12 - 15 lx, the electron concentration increases strongly n ~ L<sup>β</sup> from β ≈ 3.0, and the parameters n and μ reach relatively high values ~(10<sup>15</sup> - 10<sup>16</sup>) sm<sup>-3</sup> and ~(150 - 200) sm<sup>2</sup>/V·s, however further, at L > 50 lx, a weak dependence of n(L) and μ(L) with β, γ < 1.0 is found. The obtained experimental results are interpreted on the basis of a model of a semiconductor film with intergranular potential barriers when the concentration and barrier mechanisms of photoconductivity operate simultaneously.展开更多
In order to prolong the service life of castables for hot blast stove pipes,effects of SiO2 micropowder addition and aggregate kind on properties of castables for hot blast stove pipes,and properties of silica sol bon...In order to prolong the service life of castables for hot blast stove pipes,effects of SiO2 micropowder addition and aggregate kind on properties of castables for hot blast stove pipes,and properties of silica sol bonded castables were researched using homogenized bauxite,andalusite particles,andalusite fines,white fused corundum fines,α-Al2O3 micropowder,pure calcium aluminate cement,SiO2 micropowder,and silica sol as starting materials. The results show that：（1） as SiO2 micropowder addition increases,the shrinkage rate of fired specimens increases; BD increases firstly,reaches the highest at 4 mass%,and then decreases; CMOR and CCS of all specimens increase gradually; so the appropriate SiO2 micropowder addition is 4 mass%;（2） the specimens with bauxite aggregate have better CCS and volume stability,but specimens with andalusite aggregate have better thermal shock resistance;（ 3） for castables for hot blast stoves using silica sol as binder,the addition of pure calcium aluminate cement can decrease the linear change rate after treatment at 1 400℃ and can slightly enhance CCS and CMOR,but has very little influence on AP and BD; and the introduction of citric acid worsens the thermal shock resistance of specimens.展开更多
Magnesia chrome bricks were prepared with fiLsed MgO- Cr2 O3 synthesized material, fused magnesite and ：hrome ore as main starting materials. Nano-Al2O3 was tdded into refractories （ 2% , 4% and 6% in mass ） ;ubst...Magnesia chrome bricks were prepared with fiLsed MgO- Cr2 O3 synthesized material, fused magnesite and ：hrome ore as main starting materials. Nano-Al2O3 was tdded into refractories （ 2% , 4% and 6% in mass ） ;ubstit,ting for Al203 micropowder. After m＆ing and ;haping, the bricks were fired at 1 550 ℃, 1 600 91℃, t 650 ℃ and 1 750℃, respectively. The microstruc-ure , sintering property, mechanical properties, thermal ;kock resistance and shtg resistance of the specimens with he addition of nano-Al2O3 were investigated. The results indicate that the performance of brick with 4 mass% of nano-Al2O3 is greatly improred afier firing at 1 650 ℃.展开更多
Palladium-based alloy is a kind of material with a high glass forming ability and can be easily formed into an amorphous state. After an annealing process, it can also be maintained at a crystallized state. To study t...Palladium-based alloy is a kind of material with a high glass forming ability and can be easily formed into an amorphous state. After an annealing process, it can also be maintained at a crystallized state. To study the thermal and electrical transport properties of crystallized palladium-based alloys, the steady-state T-type method, standard four-probe method, and AC heating-DC detecting T-type method were used to measure the thermal conductivity, electrical conductivity, and Seebeck coeffi- cient of crystallized Pd4oNiloCu3oP2o and Pd43Nilo- Cu27P2o alloys respectively. The results show that compared to amorphous samples, the thermal conductivity and electrical conductivity of crystallized palladium-based alloys are significantly higher, while the Seebeck coeffi- cient is lower. The ratio of crystallized and amorphous thermal conductivity is higher for Pd43Ni10Cu27P2o alloy fiber which has a higher glass forming ability, while the ratio of electronic thermal conductivity almost remains constant for both alloy fibers. The results also show that the slope of electrical resistivity to temperature is a function of elemental composition for crystallized quaternary palla- dium-based alloy fibers. The sensitivity of thermal conductivity and electrical conductivity to the composition is high, while the correlation between Seebeck coefficient and composition is relatively weak.展开更多
In this paper the effects of temperature on the radial breathing modes （RBMs） and radial wave propaga- tion in multiwall carbon nanotubes （MWCNTs） are inves- tigated using a continuum model of multiple elastic iso...In this paper the effects of temperature on the radial breathing modes （RBMs） and radial wave propaga- tion in multiwall carbon nanotubes （MWCNTs） are inves- tigated using a continuum model of multiple elastic isotropic shells. The van der Waals forces between tubes are simulated as a nonlinear function of interlayer spacing of MWCNTs. The governing equations are solved using a finite element method. A wide range of innermost radius-to-thickness ratio of MWCNTs is considered to enhance the investigation. The presented solution is verified by comparing the results with those reported in the literature. The effects of temperature on the van der Waals interaction coefficient between layers of MWCNTs are examined. It is found that the variation of the van der Waals interaction coefficient at high temperature is sensible. Subsequently, variations of RBM frequencies and radial wave propagation in MWCNTs with temperatures up to 1 600 K are illustrated. It is shown that the thick MWC- NTs are more sensible to temperature than the thin ones.展开更多
Rocks are composed of mineral particles and micropores between mineral which has a great influence on the mechanical properties of rocks. In this paper, based on the theory of locked-in stress developed by academician...Rocks are composed of mineral particles and micropores between mineral which has a great influence on the mechanical properties of rocks. In this paper, based on the theory of locked-in stress developed by academician Chen Zongji, the locked-in stress problem in underground rock is simulated by the thermal expansion of hard rubber particles. The pore inclusion in rock is assumed to be uniformly distributed spherical cavities. Using the thermal stress theory, the stress of rock with a spherical pore inclusion is equivalent to the thermal stress generated by the spherical hard rubber inclusion. The elastic theory formula of the temperature increment and the equivalent pore pressure of the spherical hard rubber inclusion is derived. The numerical simulation of the rock mass model with a spherical hard rubber inclusion is carried out and compared to the theoretical calculation results<span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-ansi-language:en-us;mso-fareast-language:zh-cn;mso-bidi-language:ar-sa;mso-bidi-font-weight:bold;"="">;</span><span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-ansi-language:en-us;mso-fareast-language:en-us;mso-bidi-language:ar-sa;mso-bidi-font-weight:bold;"=""> the results show that they are consistent. The method proposed by this paper for simulating stress distribution in rock by thermal stress is reasonable and feasible</span><span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-ansi-language:en-us;mso-fareast-language:zh-cn;mso-bidi-language:ar-sa;mso-bidi-font-weight:bold;"="">;</span><span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-a展开更多
Here thermal dependence conductivity and nonlinear convection features in third-grade liquid flow bounded by moving surface having varying thickness are formulated. Stagnation point flow is considered. Revised Fourier...Here thermal dependence conductivity and nonlinear convection features in third-grade liquid flow bounded by moving surface having varying thickness are formulated. Stagnation point flow is considered. Revised FourierFick relations and double stratification phenomena are utilized for modeling energy and concentration expressions.Mathematical model of considered physical problem is achieved by implementing the idea of boundary layer theory. The acquired partial differential system is transformed into ordinary ones by employing relevant variables. The homotopic scheme yield convergent solutions of governing nonlinear expressions. Graphs are constructed for distinct values of physical constraints to elaborate the heat/mass transportation mechanisms.展开更多
The emerging applications of composite gels as thermal interface ma-terials(TIMs)for chip heat dissipation in intelligent vehicle and wear-able devices require high thermal conductivity and remarkable damp-ing propert...The emerging applications of composite gels as thermal interface ma-terials(TIMs)for chip heat dissipation in intelligent vehicle and wear-able devices require high thermal conductivity and remarkable damp-ing properties.However,thermal conductivity and damping proper-ties are usually correlated and coupled each other.Here,inspired by Maxwell theory and adhesion mechanism of gecko’s setae,we present a strategy to fabricate polydimethylsiloxane-based composite gels in-tegrating high thermal conductivity and remarkable damping prop-erties over a broad frequency and temperature range.The multiple relaxation modes of dangling chains and the dynamic interaction be-tween the dangling chains and aluminum fillers can efficiently dis-sipate the vibration energy,endowing the composite gels with ultra-high damping property(tanδ>0.3)over a broad frequency(0.01-100 Hz)and temperature range(-50-150°C),which exceeds typi-cal state-of-the-art damping materials.The dangling chains also com-fort to the interfaces between polymer matrix and aluminum via van der Waals interaction,resulting in high thermal conductivity(4.72±0.04 W m-1 K-1).Using the polydimethylsiloxane-based composite gel as TIMs,we demonstrate effective heat dissipation in chip oper-ating under vigorous vibrations.We believe that our strategy could be applied to a wide range of composite gels and lead to the devel-opment of high-performance composite gels as TIMs for chip heat dissipation.展开更多
基金Project supported by the National Natural Science Foundation of China （No. 20803058）, the Basal Science Foundation of National Defense （No. B 0920110005 ） and the Education Committee Foundation of S haanxi Province （Nos. 2010J K881, 09J K820）.
文摘2-（Dinitromethylene）-1,3-diazacycloheptane （DNDH） was prepared by the reaction of 1,1-diamino-2,2-dinitro- ethylene （FOX-7） with 1,4-diaminoethane in NMP. Thermal decomposition behavior of DNDH was studied under the non-isothermal conditions with DSC method, and presents only one intensely exothermic decomposition process The kinetic equation of the decomposition reaction is da/dT= 103388× 3a2/3exp（--3.353 ×10^5/RT）/fl. The critical temperature of thermal explosion is 215.97℃. Specific heat capacity of DNDH was studied with micro-DSC method and theoretical calculation method, and the molar heat capacity is 215.40 Jomol-1,K-1 at 298.15 K. Adiabatic time-to-explosion was calculated to be 92.07 s. DNDH has same thermal stability to FOX-7.
文摘The influence of thermal treatment on the lux-ampere characteristics of polycrystalline films from the CdSe<sub>x</sub>S<sub>1-x</sub> solid solution obtained by the method of thermal evaporation in a vacuum has been investigated. It is shown that at low illumination intensities L μ of electrons increases with a power law μ ~ L<sup>γ</sup>, first with the exponent γ > 1, then with γ ≈ 0.5, and their concentration n almost does not change. Starting from the intensity L > 12 - 15 lx, the electron concentration increases strongly n ~ L<sup>β</sup> from β ≈ 3.0, and the parameters n and μ reach relatively high values ~(10<sup>15</sup> - 10<sup>16</sup>) sm<sup>-3</sup> and ~(150 - 200) sm<sup>2</sup>/V·s, however further, at L > 50 lx, a weak dependence of n(L) and μ(L) with β, γ < 1.0 is found. The obtained experimental results are interpreted on the basis of a model of a semiconductor film with intergranular potential barriers when the concentration and barrier mechanisms of photoconductivity operate simultaneously.
文摘In order to prolong the service life of castables for hot blast stove pipes,effects of SiO2 micropowder addition and aggregate kind on properties of castables for hot blast stove pipes,and properties of silica sol bonded castables were researched using homogenized bauxite,andalusite particles,andalusite fines,white fused corundum fines,α-Al2O3 micropowder,pure calcium aluminate cement,SiO2 micropowder,and silica sol as starting materials. The results show that：（1） as SiO2 micropowder addition increases,the shrinkage rate of fired specimens increases; BD increases firstly,reaches the highest at 4 mass%,and then decreases; CMOR and CCS of all specimens increase gradually; so the appropriate SiO2 micropowder addition is 4 mass%;（2） the specimens with bauxite aggregate have better CCS and volume stability,but specimens with andalusite aggregate have better thermal shock resistance;（ 3） for castables for hot blast stoves using silica sol as binder,the addition of pure calcium aluminate cement can decrease the linear change rate after treatment at 1 400℃ and can slightly enhance CCS and CMOR,but has very little influence on AP and BD; and the introduction of citric acid worsens the thermal shock resistance of specimens.
文摘Magnesia chrome bricks were prepared with fiLsed MgO- Cr2 O3 synthesized material, fused magnesite and ：hrome ore as main starting materials. Nano-Al2O3 was tdded into refractories （ 2% , 4% and 6% in mass ） ;ubstit,ting for Al203 micropowder. After m＆ing and ;haping, the bricks were fired at 1 550 ℃, 1 600 91℃, t 650 ℃ and 1 750℃, respectively. The microstruc-ure , sintering property, mechanical properties, thermal ;kock resistance and shtg resistance of the specimens with he addition of nano-Al2O3 were investigated. The results indicate that the performance of brick with 4 mass% of nano-Al2O3 is greatly improred afier firing at 1 650 ℃.
文摘Palladium-based alloy is a kind of material with a high glass forming ability and can be easily formed into an amorphous state. After an annealing process, it can also be maintained at a crystallized state. To study the thermal and electrical transport properties of crystallized palladium-based alloys, the steady-state T-type method, standard four-probe method, and AC heating-DC detecting T-type method were used to measure the thermal conductivity, electrical conductivity, and Seebeck coeffi- cient of crystallized Pd4oNiloCu3oP2o and Pd43Nilo- Cu27P2o alloys respectively. The results show that compared to amorphous samples, the thermal conductivity and electrical conductivity of crystallized palladium-based alloys are significantly higher, while the Seebeck coeffi- cient is lower. The ratio of crystallized and amorphous thermal conductivity is higher for Pd43Ni10Cu27P2o alloy fiber which has a higher glass forming ability, while the ratio of electronic thermal conductivity almost remains constant for both alloy fibers. The results also show that the slope of electrical resistivity to temperature is a function of elemental composition for crystallized quaternary palla- dium-based alloy fibers. The sensitivity of thermal conductivity and electrical conductivity to the composition is high, while the correlation between Seebeck coefficient and composition is relatively weak.
文摘In this paper the effects of temperature on the radial breathing modes （RBMs） and radial wave propaga- tion in multiwall carbon nanotubes （MWCNTs） are inves- tigated using a continuum model of multiple elastic isotropic shells. The van der Waals forces between tubes are simulated as a nonlinear function of interlayer spacing of MWCNTs. The governing equations are solved using a finite element method. A wide range of innermost radius-to-thickness ratio of MWCNTs is considered to enhance the investigation. The presented solution is verified by comparing the results with those reported in the literature. The effects of temperature on the van der Waals interaction coefficient between layers of MWCNTs are examined. It is found that the variation of the van der Waals interaction coefficient at high temperature is sensible. Subsequently, variations of RBM frequencies and radial wave propagation in MWCNTs with temperatures up to 1 600 K are illustrated. It is shown that the thick MWC- NTs are more sensible to temperature than the thin ones.
文摘Rocks are composed of mineral particles and micropores between mineral which has a great influence on the mechanical properties of rocks. In this paper, based on the theory of locked-in stress developed by academician Chen Zongji, the locked-in stress problem in underground rock is simulated by the thermal expansion of hard rubber particles. The pore inclusion in rock is assumed to be uniformly distributed spherical cavities. Using the thermal stress theory, the stress of rock with a spherical pore inclusion is equivalent to the thermal stress generated by the spherical hard rubber inclusion. The elastic theory formula of the temperature increment and the equivalent pore pressure of the spherical hard rubber inclusion is derived. The numerical simulation of the rock mass model with a spherical hard rubber inclusion is carried out and compared to the theoretical calculation results<span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-ansi-language:en-us;mso-fareast-language:zh-cn;mso-bidi-language:ar-sa;mso-bidi-font-weight:bold;"="">;</span><span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-ansi-language:en-us;mso-fareast-language:en-us;mso-bidi-language:ar-sa;mso-bidi-font-weight:bold;"=""> the results show that they are consistent. The method proposed by this paper for simulating stress distribution in rock by thermal stress is reasonable and feasible</span><span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-ansi-language:en-us;mso-fareast-language:zh-cn;mso-bidi-language:ar-sa;mso-bidi-font-weight:bold;"="">;</span><span lang="EN-US" style="font-family:;" minion="" pro="" capt",serif;font-size:10pt;mso-fareast-font-family:宋体;mso-bidi-font-family:"times="" new="" roman";mso-a
文摘Here thermal dependence conductivity and nonlinear convection features in third-grade liquid flow bounded by moving surface having varying thickness are formulated. Stagnation point flow is considered. Revised FourierFick relations and double stratification phenomena are utilized for modeling energy and concentration expressions.Mathematical model of considered physical problem is achieved by implementing the idea of boundary layer theory. The acquired partial differential system is transformed into ordinary ones by employing relevant variables. The homotopic scheme yield convergent solutions of governing nonlinear expressions. Graphs are constructed for distinct values of physical constraints to elaborate the heat/mass transportation mechanisms.
基金This work was supported by the National Key Research and Development Program of China(No.2020YFB040176)National Natural Science Foundation of China(No.52073300 and 62104161)+3 种基金the Youth Innovation Promotion Association of the Chinese Academy of Sciences(2019354)Guangdong Province Key Field R&D Program Project(No.2020B010190004),Shenzhen Science and Technology Research Funding(No.JCYJ20200109114401708)Key Project of Science and Technol-ogy of Changsha(kq2102005)Guangdong Provincial Key Laboratory(2014B030301014).
文摘The emerging applications of composite gels as thermal interface ma-terials(TIMs)for chip heat dissipation in intelligent vehicle and wear-able devices require high thermal conductivity and remarkable damp-ing properties.However,thermal conductivity and damping proper-ties are usually correlated and coupled each other.Here,inspired by Maxwell theory and adhesion mechanism of gecko’s setae,we present a strategy to fabricate polydimethylsiloxane-based composite gels in-tegrating high thermal conductivity and remarkable damping prop-erties over a broad frequency and temperature range.The multiple relaxation modes of dangling chains and the dynamic interaction be-tween the dangling chains and aluminum fillers can efficiently dis-sipate the vibration energy,endowing the composite gels with ultra-high damping property(tanδ>0.3)over a broad frequency(0.01-100 Hz)and temperature range(-50-150°C),which exceeds typi-cal state-of-the-art damping materials.The dangling chains also com-fort to the interfaces between polymer matrix and aluminum via van der Waals interaction,resulting in high thermal conductivity(4.72±0.04 W m-1 K-1).Using the polydimethylsiloxane-based composite gel as TIMs,we demonstrate effective heat dissipation in chip oper-ating under vigorous vibrations.We believe that our strategy could be applied to a wide range of composite gels and lead to the devel-opment of high-performance composite gels as TIMs for chip heat dissipation.
