近年来,高时空分辨率的全球导航卫星系统(GNSS)观测信号已成为电离层研究的重要资源.利用GNSS研究电离层,需首先将观测资料转换成包含电离层信息的可观测量(Ionospheric Observables,称之为"电离层观测值").目前,最常用的电...近年来,高时空分辨率的全球导航卫星系统(GNSS)观测信号已成为电离层研究的重要资源.利用GNSS研究电离层,需首先将观测资料转换成包含电离层信息的可观测量(Ionospheric Observables,称之为"电离层观测值").目前,最常用的电离层观测值一般采用联合无几何影响组合的码和相位观测,利用相位平滑伪距方法计算得到(称之为"平滑电离层观测值"),但该过程易受平滑弧段长度和与测站有关的误差(如多路径效应和观测噪声)的影响.本文提出利用精密单点定位(Precise Point Positioning,PPP)提取电离层观测值(称之为"PPP电离层观测值",形式与平滑电离层观测值相同).与相位平滑伪距相比,IGS发布的卫星轨道、钟差产品可被PPP合理利用,从而有效减少了待估参数,使得电离层观测值的估计精度得到改善.基于短基线和零基线实验,通过考察两类电离层观测值的站间单差结果在各卫星弧段间的离散程度,验证了PPP电离层观测值的可靠性:以某两天的短基线实验结果为例,与测站有关的误差对PPP电离层观测值的影响分别为对平滑电离层观测值影响的44.4%和35.7%,表明PPP电离层观测值更利于高精度电离层建模、预报等研究.展开更多
The inter-electrode gap(IEG) is an essential parameter for the anode shaping process in electrochemical machining(ECM) and directly affects the machining accuracy. In this paper, the IEG during the leveling process of...The inter-electrode gap(IEG) is an essential parameter for the anode shaping process in electrochemical machining(ECM) and directly affects the machining accuracy. In this paper, the IEG during the leveling process of an oval anode workpiece in counter-rotating ECM(CRECM)is investigated. The variation of the minimum IEG is analyzed theoretically, and the results indicate that rather than reaching equilibrium, the minimum IEG in CRECM expands constantly when a constant feed speed is used for the cathode tool. This IEG expansion leads to a poor localization effect and has an adverse influence on the roundness of the machined workpiece. To maintain a small constant IEG in CRECM, a variable feed speed is used for the cathode based on a fitted equation. The theoretical results show that the minimum IEG can be controlled at a small value by using an accelerated feed speed. Experiments have been conducted using a specific experimental apparatus in which the cathode tool is designed as a combined structure of two sectors and a thin sheet. By detecting the machining currents flowing through the minimum IEG, how the latter varies is obtained indirectly. The results indicate that using an accelerated feed speed is effective for controlling the IEG, thereby improving the roundness of the machined workpiece.展开更多
The post-seismic horizontal and vertical deformations following the 2008 Ms8.0 Wenchuan earth- quake are inferred from GPS and precise leveling data. The post-seismic relaxation process is measured using GPS data from...The post-seismic horizontal and vertical deformations following the 2008 Ms8.0 Wenchuan earth- quake are inferred from GPS and precise leveling data. The post-seismic relaxation process is measured using GPS data from campaign stations located around the Longmenshan fault, and the derived decay time constant is 12 days. The evolution of the post-seismic vertical deformation is obtained from precise leveling data measured near the surface rupture. The results demonstrate that the hanging wall is uplifting and the foot wall is subsi- ding. The amplitude of the post-seismic deformation is lower than that of the co-seismic deformation. The re- gion with the largest post-seismic displacement is located on the leveling route between Maoxian and Beichuan on the hanging wall.展开更多
文摘近年来,高时空分辨率的全球导航卫星系统(GNSS)观测信号已成为电离层研究的重要资源.利用GNSS研究电离层,需首先将观测资料转换成包含电离层信息的可观测量(Ionospheric Observables,称之为"电离层观测值").目前,最常用的电离层观测值一般采用联合无几何影响组合的码和相位观测,利用相位平滑伪距方法计算得到(称之为"平滑电离层观测值"),但该过程易受平滑弧段长度和与测站有关的误差(如多路径效应和观测噪声)的影响.本文提出利用精密单点定位(Precise Point Positioning,PPP)提取电离层观测值(称之为"PPP电离层观测值",形式与平滑电离层观测值相同).与相位平滑伪距相比,IGS发布的卫星轨道、钟差产品可被PPP合理利用,从而有效减少了待估参数,使得电离层观测值的估计精度得到改善.基于短基线和零基线实验,通过考察两类电离层观测值的站间单差结果在各卫星弧段间的离散程度,验证了PPP电离层观测值的可靠性:以某两天的短基线实验结果为例,与测站有关的误差对PPP电离层观测值的影响分别为对平滑电离层观测值影响的44.4%和35.7%,表明PPP电离层观测值更利于高精度电离层建模、预报等研究.
基金supported by the National Natural Science Foundation of China (51535006, 51805259)Natural Science Foundation of Jiangsu Province of China (BK20180431)+2 种基金Fundamental Research Funds for the Central Universities of China (3082018NP2018406)Young Elite Scientists Sponsorship Program by CAST of ChinaJiangsu Key Laboratory of Precision and Micro-Manufacturing Technology of China
文摘The inter-electrode gap(IEG) is an essential parameter for the anode shaping process in electrochemical machining(ECM) and directly affects the machining accuracy. In this paper, the IEG during the leveling process of an oval anode workpiece in counter-rotating ECM(CRECM)is investigated. The variation of the minimum IEG is analyzed theoretically, and the results indicate that rather than reaching equilibrium, the minimum IEG in CRECM expands constantly when a constant feed speed is used for the cathode tool. This IEG expansion leads to a poor localization effect and has an adverse influence on the roundness of the machined workpiece. To maintain a small constant IEG in CRECM, a variable feed speed is used for the cathode based on a fitted equation. The theoretical results show that the minimum IEG can be controlled at a small value by using an accelerated feed speed. Experiments have been conducted using a specific experimental apparatus in which the cathode tool is designed as a combined structure of two sectors and a thin sheet. By detecting the machining currents flowing through the minimum IEG, how the latter varies is obtained indirectly. The results indicate that using an accelerated feed speed is effective for controlling the IEG, thereby improving the roundness of the machined workpiece.
基金supported by the Special Earthquake Research Project Granted by the China Earthquake Administration(201208006)the National Natural Science Foundation of China(41174083,40974062)
文摘The post-seismic horizontal and vertical deformations following the 2008 Ms8.0 Wenchuan earth- quake are inferred from GPS and precise leveling data. The post-seismic relaxation process is measured using GPS data from campaign stations located around the Longmenshan fault, and the derived decay time constant is 12 days. The evolution of the post-seismic vertical deformation is obtained from precise leveling data measured near the surface rupture. The results demonstrate that the hanging wall is uplifting and the foot wall is subsi- ding. The amplitude of the post-seismic deformation is lower than that of the co-seismic deformation. The re- gion with the largest post-seismic displacement is located on the leveling route between Maoxian and Beichuan on the hanging wall.
