Nano-particles which can largely improve the microstructure and oxidation resistance of materials are often used as a strengthening component in metal matrix composites. However, few studies were reported on its appli...Nano-particles which can largely improve the microstructure and oxidation resistance of materials are often used as a strengthening component in metal matrix composites. However, few studies were reported on its application in the bond coat of duplex structure thermal barrier coating（TBC）. Three kinds of NiCoCrAlY coatings strengthened by different nano-particles with the same addition （1%, mass fraction） were prepared by the laser cladding technique on Ni-based superalloy substrates, aiming to study the effects of the nano-particles on microstructure and oxidation resistance of NiCoCrAlY coatings （the bond coat of the duplex structure thermal barrier coatings）. Scanning electron microscope （SEM）, X-ray diffractometer（XRD） and thermogravimetry were employed to investigate their morphologies, phases and cyclic oxidation behaviors in atmosphere at 1 050℃, compared with the coating without nano-particles. With the addition of nano-particles, the growth pattern of the grains at the interface changed from epitaxial growth to non-epitaxial growth or part-epitaxial growth; slender dendrites were broken and cellularized; cracks and pores were restrained; and the oxidation weight-gain and the stripping resistance of the oxide scale were improved as well. Among the three kinds of nano-particles, the SiC nano-particles showed the most improvement on microstructure, while the CeO2 nano-particles were insufficient, but its effects on the oxidation resistance are the same as those of the SiC nano-particles. Based on the discussions of the influence mechanism, it is believed that CeO2 nano-particles would show better improvement than SiC nano-particles if the proper amount is added and the proper preparation technique of micro-nanometer composite powders is adopted, with the synergistic action of nanometer effect and reactive element effect.展开更多
The subject of this study is the oxidation of fuel rod cladding made of material Zr1Nb(0.1% O) in steam at temperatures in the range of 660℃ to 1200℃ with a surface in the initial state (after manufacturing - grindi...The subject of this study is the oxidation of fuel rod cladding made of material Zr1Nb(0.1% O) in steam at temperatures in the range of 660℃ to 1200℃ with a surface in the initial state (after manufacturing - grinding) and after additional chemical etching. The changes in the microstructure of tubes due to the interaction with steam were investigated. A comparison was made between the oxidation rate of this material (weight gain) and the data on the oxidation of other alloys for nuclear power plants. The oxidation rate of Zr1Nb(0.1% O) is close to the oxidation rate of other zirconium alloys. It is shown that after chemical treatment of the surface of the samples there is a more even growth of oxide films, and they have a smaller thickness for the same time of exposure than after mechanical grinding. Surface treatment before oxidation also affects the change of microstructure of samples when heated to high temperatures.展开更多
The QUENCH experimental programme at Karlsruhe under severe accident conditions, but while the geometry is still Institute of Technology investigates heat-up and reflooding of a core mainly rod-like. The recent QUENCH...The QUENCH experimental programme at Karlsruhe under severe accident conditions, but while the geometry is still Institute of Technology investigates heat-up and reflooding of a core mainly rod-like. The recent QUENCH-ACM series of experiments, comprising QUENCH-12 （El 10 cladding alloy）, -14 （M5 alloy） and -15 （Zirlo^TM alloy）, together with QUENCH-06 （reference case, Zircaloy-4 alloy） addressed the effect of alternative cladding materials on oxidation and quenching under similar conditions. Superficial inspection of the experimental results reveals only minor differences in the thermal and oxidation response, except for the much larger hydrogen release during reflood in QUENCH-12. Post-test calculations were performed using a version of SCDAP/RELAP5/MOD3.2, modified to represent the QUENCH facility and to invoke alternative oxidation correlations. The calculations agreed rather well with experiments QUENCH-06, -14 and -15, but the significant hydrogen release during reflood in QUENCH-12 was not captured. Closer examination of the experimental results reveals further differences between QUENCH-12 which may be linked to breakaway oxidation of the E110 cladding. The analyses support the heuristic observation that there was no major difference between the influence of Zircaloy-4, M5 or ZirloTM, but the E-110 exhibited a contrasting behaviour with a consequent impact on the reflooding.展开更多
针对我国国产反应堆严重事故分析程序的发展需要,西安交通大学开发了一体化严重事故分析程序(modular severe accident analysis program,MOSAP)。为了验证MOSAP程序在再淹没期间相关模型的合理性和准确性,以QUENCH-06实验为例,利用MOSA...针对我国国产反应堆严重事故分析程序的发展需要,西安交通大学开发了一体化严重事故分析程序(modular severe accident analysis program,MOSAP)。为了验证MOSAP程序在再淹没期间相关模型的合理性和准确性,以QUENCH-06实验为例,利用MOSAP程序对实验进行建模,并将MOSAP程序的计算结果与实验结果以及国际通用程序的计算结果进行了对比。结果表明,对于包壳轴向温度、包壳氧化层厚度和氢气产量,MOSAP程序计算结果与实验值和国际通用程序计算结果符合良好。在计算包壳轴向温度和氧化层厚度方面,MOSAP程序计算结果优于国际通用程序计算结果。文中结论对MOSAP程序堆内模块验证和整个模块的验证具有一定的参考意义。展开更多
基金supported by Specialized Research Fund for Doctoral Program of Higher Education of China (Grant No. 20060287019)Opening Research Fund of Jiangsu Provincial Key Laboratory of Tribology of China (Grant No. kjsmcx07001)Jiangsu Provincial Graduate Innovation Foundation of China (Grant No. CX08B-039Z)
文摘Nano-particles which can largely improve the microstructure and oxidation resistance of materials are often used as a strengthening component in metal matrix composites. However, few studies were reported on its application in the bond coat of duplex structure thermal barrier coating（TBC）. Three kinds of NiCoCrAlY coatings strengthened by different nano-particles with the same addition （1%, mass fraction） were prepared by the laser cladding technique on Ni-based superalloy substrates, aiming to study the effects of the nano-particles on microstructure and oxidation resistance of NiCoCrAlY coatings （the bond coat of the duplex structure thermal barrier coatings）. Scanning electron microscope （SEM）, X-ray diffractometer（XRD） and thermogravimetry were employed to investigate their morphologies, phases and cyclic oxidation behaviors in atmosphere at 1 050℃, compared with the coating without nano-particles. With the addition of nano-particles, the growth pattern of the grains at the interface changed from epitaxial growth to non-epitaxial growth or part-epitaxial growth; slender dendrites were broken and cellularized; cracks and pores were restrained; and the oxidation weight-gain and the stripping resistance of the oxide scale were improved as well. Among the three kinds of nano-particles, the SiC nano-particles showed the most improvement on microstructure, while the CeO2 nano-particles were insufficient, but its effects on the oxidation resistance are the same as those of the SiC nano-particles. Based on the discussions of the influence mechanism, it is believed that CeO2 nano-particles would show better improvement than SiC nano-particles if the proper amount is added and the proper preparation technique of micro-nanometer composite powders is adopted, with the synergistic action of nanometer effect and reactive element effect.
文摘The subject of this study is the oxidation of fuel rod cladding made of material Zr1Nb(0.1% O) in steam at temperatures in the range of 660℃ to 1200℃ with a surface in the initial state (after manufacturing - grinding) and after additional chemical etching. The changes in the microstructure of tubes due to the interaction with steam were investigated. A comparison was made between the oxidation rate of this material (weight gain) and the data on the oxidation of other alloys for nuclear power plants. The oxidation rate of Zr1Nb(0.1% O) is close to the oxidation rate of other zirconium alloys. It is shown that after chemical treatment of the surface of the samples there is a more even growth of oxide films, and they have a smaller thickness for the same time of exposure than after mechanical grinding. Surface treatment before oxidation also affects the change of microstructure of samples when heated to high temperatures.
文摘The QUENCH experimental programme at Karlsruhe under severe accident conditions, but while the geometry is still Institute of Technology investigates heat-up and reflooding of a core mainly rod-like. The recent QUENCH-ACM series of experiments, comprising QUENCH-12 （El 10 cladding alloy）, -14 （M5 alloy） and -15 （Zirlo^TM alloy）, together with QUENCH-06 （reference case, Zircaloy-4 alloy） addressed the effect of alternative cladding materials on oxidation and quenching under similar conditions. Superficial inspection of the experimental results reveals only minor differences in the thermal and oxidation response, except for the much larger hydrogen release during reflood in QUENCH-12. Post-test calculations were performed using a version of SCDAP/RELAP5/MOD3.2, modified to represent the QUENCH facility and to invoke alternative oxidation correlations. The calculations agreed rather well with experiments QUENCH-06, -14 and -15, but the significant hydrogen release during reflood in QUENCH-12 was not captured. Closer examination of the experimental results reveals further differences between QUENCH-12 which may be linked to breakaway oxidation of the E110 cladding. The analyses support the heuristic observation that there was no major difference between the influence of Zircaloy-4, M5 or ZirloTM, but the E-110 exhibited a contrasting behaviour with a consequent impact on the reflooding.
文摘针对我国国产反应堆严重事故分析程序的发展需要,西安交通大学开发了一体化严重事故分析程序(modular severe accident analysis program,MOSAP)。为了验证MOSAP程序在再淹没期间相关模型的合理性和准确性,以QUENCH-06实验为例,利用MOSAP程序对实验进行建模,并将MOSAP程序的计算结果与实验结果以及国际通用程序的计算结果进行了对比。结果表明,对于包壳轴向温度、包壳氧化层厚度和氢气产量,MOSAP程序计算结果与实验值和国际通用程序计算结果符合良好。在计算包壳轴向温度和氧化层厚度方面,MOSAP程序计算结果优于国际通用程序计算结果。文中结论对MOSAP程序堆内模块验证和整个模块的验证具有一定的参考意义。
