Microstructure features of 12 MnNiVR pressure vessel steel welded joint deposited by the high heat input electrogas welding have been systematically investigated. It is revealed that the welded joint is featured by a ...Microstructure features of 12 MnNiVR pressure vessel steel welded joint deposited by the high heat input electrogas welding have been systematically investigated. It is revealed that the welded joint is featured by a heterogeneous juxtaposition. The coarse grained heat-affected zone(CGHAZ) primarily consists of lath bainites and minor granular bainites. The fine grained heat-affected zone(FGHAZ) is dominated by polygonal ferrites, pearlites, and fine cementite particles. Moreover, electron backscatter diffraction results further demonstrate that the CGHAZ is populated by coarse prior austenite grains(PAGs) with high frequency(61.3%) of low angle grain boundaries(LAGBs). On the other hand, the FGHAZ is filled with fine PAGs with a lower frequency(19.6%) of LAGBs. Such microstructural differences may likely contribute to differed mechanical properties for samples tested at designed positions.展开更多
Austenite grain sizes in the heat affected zone （HAZ） of a high heat input welded Zr-Ti bearing microal- loyed steel are measured under different welding conditions simulated by a Gleeble-1500 thermal-mechanical sim...Austenite grain sizes in the heat affected zone （HAZ） of a high heat input welded Zr-Ti bearing microal- loyed steel are measured under different welding conditions simulated by a Gleeble-1500 thermal-mechanical simulator. The austenite grain growth is divided into two regimes in terms of temperature. When the temperature is lower than 1 250℃ where the pinning effect of precipitates is strong, the austenite grain size increases slowly with increas- ing peak temperature, but it increases drastically when the temperature is higher than 1 250 ~C where the pinning effect of precipitates is weak. Based on the experimental measurements, an analytical model for predicting the aus- tenite grain size in the heat affected zone is derived. Model predictions indicate that the initial grain size has little effect on the final one, and the grain growth depends mainly on heat input and peak temperature as well as growth activation energy and exponent. With the use of the model, the width of coarse grained heat affected zone （CGHAZ） for a thick plate is predicted.展开更多
为了研究EH36海洋平台用钢焊接工艺,对100 mm厚的EH36海洋平台大线能量用钢进行了大线能量埋弧焊焊接试验。焊后对焊接接头进行了综合性能测试和微观组织分析。结果表明,焊缝表面及中心部位组织由大量针状铁素体、少量先共析铁素体和少...为了研究EH36海洋平台用钢焊接工艺,对100 mm厚的EH36海洋平台大线能量用钢进行了大线能量埋弧焊焊接试验。焊后对焊接接头进行了综合性能测试和微观组织分析。结果表明,焊缝表面及中心部位组织由大量针状铁素体、少量先共析铁素体和少量M-A组元组成,焊缝接头具有良好的韧性。接头硬度测试表明,EH36大线能量用钢在100 k J/cm热输入条件下,焊缝及热影响区具备较好的硬度,满足热输入条件下焊接施工条件。展开更多
基金financially supported by the National Natural Science Foundation of China (Nos. 51622401, 51628402, 51861145312 and 51861130361)the National Key Research and Development Program of China (2016YFB0300602)+3 种基金the Research Fund for Central Universities (No. N172502004)State Key Laboratory of Solidification Processing, Northwestern Polytechnical University (No. SKLSP201805)the Global Talents Recruitment Program endowed by the Chinese Governmentsupport from Jiangyin Xingcheng Special Steel Works Co., Ltd.
文摘Microstructure features of 12 MnNiVR pressure vessel steel welded joint deposited by the high heat input electrogas welding have been systematically investigated. It is revealed that the welded joint is featured by a heterogeneous juxtaposition. The coarse grained heat-affected zone(CGHAZ) primarily consists of lath bainites and minor granular bainites. The fine grained heat-affected zone(FGHAZ) is dominated by polygonal ferrites, pearlites, and fine cementite particles. Moreover, electron backscatter diffraction results further demonstrate that the CGHAZ is populated by coarse prior austenite grains(PAGs) with high frequency(61.3%) of low angle grain boundaries(LAGBs). On the other hand, the FGHAZ is filled with fine PAGs with a lower frequency(19.6%) of LAGBs. Such microstructural differences may likely contribute to differed mechanical properties for samples tested at designed positions.
基金Sponsored by the Department of Science and Technology of Shenzhen (SY200806260037A)
文摘Austenite grain sizes in the heat affected zone （HAZ） of a high heat input welded Zr-Ti bearing microal- loyed steel are measured under different welding conditions simulated by a Gleeble-1500 thermal-mechanical simulator. The austenite grain growth is divided into two regimes in terms of temperature. When the temperature is lower than 1 250℃ where the pinning effect of precipitates is strong, the austenite grain size increases slowly with increas- ing peak temperature, but it increases drastically when the temperature is higher than 1 250 ~C where the pinning effect of precipitates is weak. Based on the experimental measurements, an analytical model for predicting the aus- tenite grain size in the heat affected zone is derived. Model predictions indicate that the initial grain size has little effect on the final one, and the grain growth depends mainly on heat input and peak temperature as well as growth activation energy and exponent. With the use of the model, the width of coarse grained heat affected zone （CGHAZ） for a thick plate is predicted.
文摘为了研究EH36海洋平台用钢焊接工艺,对100 mm厚的EH36海洋平台大线能量用钢进行了大线能量埋弧焊焊接试验。焊后对焊接接头进行了综合性能测试和微观组织分析。结果表明,焊缝表面及中心部位组织由大量针状铁素体、少量先共析铁素体和少量M-A组元组成,焊缝接头具有良好的韧性。接头硬度测试表明,EH36大线能量用钢在100 k J/cm热输入条件下,焊缝及热影响区具备较好的硬度,满足热输入条件下焊接施工条件。
