The microstructure and mechanical properties of 304 L stainless steel fabricated by selective laser melting are investigated in this study.With the optimized laser processing parameters,a relative density of 99.9%is a...The microstructure and mechanical properties of 304 L stainless steel fabricated by selective laser melting are investigated in this study.With the optimized laser processing parameters,a relative density of 99.9%is achieved with fine austenite grains and nanoscale cellular subgrains in size of approximately 0.5μm.The presence ofδ-ferrite andσphase precipitates is identified by the x-ray diffraction and transmission electron microscopy.Moreover,the microstructure is identified as an austenite matrix with about 4%δ-ferrite and a trace amount ofσphase by using electron backscattered diffraction analysis.These smallσphase particles are mainly distributed along austenite grain boundaries.Furthermore,the presence of nanoscale cellular subgrains contributes to the good tensile strength and ductility of the selective laser melted 304 L,along with precipitate strengthening and strain hardening.Tensile property anisotropy is also identified in this 304 L,which is attributed to the microstructure difference on vertical and horizontal planes.展开更多
分别在800℃、825℃、850℃焊接温度、30 m in保温时间,3 MPa焊接压力下,进行Ti-6A l-4V钛合金板与304L不锈钢网的真空扩散焊接。对接头组织结构与化学元素扩散进行了扫描电镜与能谱分析,并测试了接头的剪切强度。结果表明:不添加中间...分别在800℃、825℃、850℃焊接温度、30 m in保温时间,3 MPa焊接压力下,进行Ti-6A l-4V钛合金板与304L不锈钢网的真空扩散焊接。对接头组织结构与化学元素扩散进行了扫描电镜与能谱分析,并测试了接头的剪切强度。结果表明:不添加中间过渡层金属,可以成功地实现钛合金板与不锈钢网的扩散焊接,并使接头的剪切强度达到90 MPa以上。不锈钢网中的Fe、N、iCr扩散并固溶到钛合金中,稳定了β相,使钛合金在一定深度上,其组织由原来的α+β双相结构转变为单相的β相。不锈钢中的Cr,由于钛合金中Ti的扩散进入,而在界面发生了上坡扩散现象。这种Cr在不锈钢一定深度内的富集,形成窄长的富Cr区域,冷却后转变为硬脆的σ相。但在焊接接头中没有发现明显其它的金属间化合物或氧化物相的生成,使得接头的机械性能得到了很好的保证。展开更多
基金supported financially by the National Key R&D Program of China(Nos.2018 YFB1106100)the Special funds for Future Industries of Shenzhen(Project No.JSGG20170824104916638)。
文摘The microstructure and mechanical properties of 304 L stainless steel fabricated by selective laser melting are investigated in this study.With the optimized laser processing parameters,a relative density of 99.9%is achieved with fine austenite grains and nanoscale cellular subgrains in size of approximately 0.5μm.The presence ofδ-ferrite andσphase precipitates is identified by the x-ray diffraction and transmission electron microscopy.Moreover,the microstructure is identified as an austenite matrix with about 4%δ-ferrite and a trace amount ofσphase by using electron backscattered diffraction analysis.These smallσphase particles are mainly distributed along austenite grain boundaries.Furthermore,the presence of nanoscale cellular subgrains contributes to the good tensile strength and ductility of the selective laser melted 304 L,along with precipitate strengthening and strain hardening.Tensile property anisotropy is also identified in this 304 L,which is attributed to the microstructure difference on vertical and horizontal planes.
