期刊文献+

3个控制顶点的类三次Bézier螺线 被引量:4

The quasi-cubic Bézier spirals with three control points
原文传递
导出
摘要 目的为了使得过渡曲线的设计更为简单高效。提出基于3个控制顶点的类三次Bézier螺线。方法通过对基函数的研究首先构造了3条在一定条件下曲率单调递减的类三次Bézier曲线,并由参数的对称性得另3条曲率单调递增的曲线。它们具有端点性、凸包性、几何不变性等三次Bézier曲线的基本性质,特点是只有3个控制顶点。接着严格地证明了此类曲线曲率单调的充分条件。结果有两条曲线比三次Bézier曲线的曲率单调条件范围大,且类三次Bézier螺线与三次Bézier螺线存在一定的位置关系。这6条曲线中有4条曲线的一个端点处曲率为零,可组合成4对类三次Bézier螺线来构造两圆弧间半径比例不受限制的S型和C型G2连续过渡曲线;剩下的两条曲线在两圆弧半径相差较大的情况下都可做不含曲率极值点的过渡曲线。最后用实例表明了此类曲线的有效性。结论在过渡曲线设计中基于3个控制顶点的类三次Bézier螺线比三次Bézier螺线更为简单高效。 Objective This study aims to design a simple and effective transition curve. Method First, three quasi-cubic Bezier curves with monotone decreasing curvature are constructed after studying the base functions. Three other quasi-cubic Bezier curves with monotone increasing curvature are then obtained by parameter symmetry. These new curves have similar properties with the cubic Bezier curves, including endpoint, convex hull, and geometry invariability properties. However, unlike the cubic Bezier curves, the quasi-cubic Bezier curves only have three control points. We then provide strict mathe- matical proofs in relation to the sufficient conditions of the monotone curvature of these curves. Result Two of the quasi-cu- bic Bezier curves covered a broader scope than the cubic Bezier curves with monotone curvature. The specific positional re- lationship between the quasi-cubic Bezier spiral curves and the cubic Bezier spiral curves were determined. Four of the six quasi-cubic Bezier curves had zero curvature at one endpoint and can therefore be combined into four pairs of S-shaped or C-shaped transition curves for separated circles; the ratio of two radii had no restriction. The remaining two quasi-cubic Bezier curves can be used to form a single transition curve with no curvature extreme for separated circles when the differ- ence of two radii is large. Finally, examples were given to show the effectiveness of these curves. Conclusion In transition curve design, the quasi-cubic Bezier spiral curve with three control points is more simple and effective than the cubic Bezier spiral curve.
出处 《中国图象图形学报》 CSCD 北大核心 2014年第11期1677-1683,共7页 Journal of Image and Graphics
基金 国家自然科学基金项目(61272309 61472366)
关键词 三次BÉZIER曲线 类三次Bézier曲线 曲率单调 G2连续 过渡曲线 cubic Bezier curve quasi-cubic B6zier curve curvature monotony G2 continuity transition curve
  • 相关文献

参考文献14

二级参考文献38

  • 1XU Huixia,WANG Guojin.Multiple products of B-splines used in CAD system[J].Progress in Natural Science:Materials International,2006,16(4):425-430. 被引量:4
  • 2Schroeder W J, Zarge J A. Decimation of triangle meshes [ J ]. Computer Graphics, 1992, 26(2) : 65 -70. 被引量:1
  • 3Low K L, Tan T S. Modeling simplification using vertex clustering [ A ]. In: Proceedings of the ACM Siggraph [ C ], Los Angeles, CA,USA, 1997:75 -82. 被引量:1
  • 4Hoppe H. Progressive meshes [ A]. In: Proceedings of the 23rd Annual Conference on Computer Graphics and Interactive Techniques [ C ], New Orleans, LA, USA, 1996:99 - 108. 被引量:1
  • 5Garland M, Heckbert P S. Surface simplification using quadric error metrics [ A ]. In: Proceedings of the 24th Annual Conference on Computer Graphics and Interactive Techniques [ C ] , Los Angeles, CA, USA, 1997:209-216. 被引量:1
  • 6Oliver Matias van Kaick, Hello Pedrini. A Comparative Evaluation of Metrics for Fast Mesh Simplification [ J]. Computer Graphics forum, 2006, 25(2) : 197 -210. 被引量:1
  • 7Kho Y, Garland M. User-guided simplification [ A ]. In: Proceedings of ACM Symposium on Interactive 3 D Graphics [ C ], San Diego, CA, USA, 2003 : 123 - 126. 被引量:1
  • 8Kim S J, Kim C H, Levin D. Surface simplification using a discrete curvature norm [ J ]. Computers Graphics, 2002, 26 ( 5 ) : 657 - 663. 被引量:1
  • 9Lee C H, Varshney A, Jacobs D. Mesh Saliency [ J ]. ACM Transactions on Graphics, 2005, 24 (3) : 659 - 666. 被引量:1
  • 10Cignoni P, Rocchini C, Scopigno R. Metro: measuring error on simplified surfaces [ J]. Computer Graphics forum, 1998, 17 (2) : 167 - 174 被引量:1

共引文献27

同被引文献26

引证文献4

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部