期刊文献+

新颖环形喷动床颗粒喷动特性实验研究 被引量:3

Experimental Study on Particles Spouting Characteristics in a Novel Annular Spouted Bed
下载PDF
导出
摘要 一种新颖的环形喷动床由内外两个不同内径、同心的垂立圆筒组成,在环形空间底部设置多个喷口,在喷口两侧布置倾斜的导流板。研究颗粒在这种喷动床内的流动特性,探讨喷口结构、颗粒种类以及床内载料量对环形喷动床颗粒喷动特性的影响。实验结果表明:颗粒在环形喷动床内分为三个明显不同的区域,即颗粒填充移动区、密相喷动流化区以及稀相夹带区。当颗粒出现分区喷动后,随床内载料量的增多,填充移动区的高度维持不变,始终等于导流板的高度,而密相喷动区的高度不断增加。风量和颗粒种类对床层最大喷动量、密相喷动高度以及床层压力分布规律有着十分重要的影响。采用不同的喷口结构时,在相同的载料量下,直向喷口的密相喷动区高度更大,而且床内各测点的平均压力大于采用斜向喷口时的相应测点压力。 A novel annular spouted bed was developed, which was consisted of two concentric hollow cylinders with different diameters, and several nozzles with guide plates were symmetrically arranged on the bottom of the annular space between the two hollow cylinders. Experiments were conducted to study the particles spouting characteristics in the novel spouted bed, then the effects of nozzle structure, kinds of tested particles and the added amount of tested particles on the spouted fluidizing behaviors of tested particles in the annular spouted bed were discussed. The results show that the particles flow in the annular spouted bed commonly can be divided into three different zones, namely the moving packed zone, the dense-phase spouted fluidizing zone and the dilute-phase zone. Once the three different particles flow zones were established, the height of the moving packed zone will keep unchanged and will always equal to the height of the guide plates, while the height of the dense-phase spouted fluidizing zone will increase with the increase of the added amount of tested particles. It was also found that the spouting gas velocity and the difference of tested particles have important influences on the maximum spouting amount of particles, the height of dense-phase spouted fluidizing zone and the bed pressure fluctuation. Under the same spouting condition, the height of dense-phase spouted fluidizing zone and the bed pressure caused by forward nozzles is higher than those caused by angled nozzles.
出处 《高校化学工程学报》 EI CAS CSCD 北大核心 2007年第6期936-941,共6页 Journal of Chemical Engineering of Chinese Universities
基金 国家自然科学基金项目(50376033)
关键词 环形喷动床 喷动特性 导流板 压力波动 annular spouted bed spouting characteristics guide plate pressure fluctuation
  • 相关文献

参考文献18

  • 1Mathur K B, Gishler P E. A technique for contracting gases with coarse solid particles [J]. AIChE Journal, 1955, 1(1): 157-164. 被引量:1
  • 2Rasul M G. Spouted bed combustion of wood charcoal: performance comparison of three different designs [J]. Fuel, 2001, 80(15): 2189-2191. 被引量:1
  • 3金保升,董长青,朱传宝,周山明,朱世钧,李锋.喷动流化床流动形态变化的试验研究[J].煤炭转化,2000,23(4):69-73. 被引量:6
  • 4张少峰,赵卷,张占锋,彭培英,刘燕.喷动床技术在烟气脱硫中的应用及最新进展[J].化工进展,2004,23(2):162-167. 被引量:8
  • 5Cassanello M, Larachi F, Legros R et al. Solids dynamics from experimental trajectory time-series of a single particle motion in gas-spouted beds [J].Chcmical Engineering Science, 1999, 54 (13-14): 2545-2554. 被引量:1
  • 6San Jose M J, Alvarez S, Salazar A O D et al. Influence of the particle diameter and density in the gas velocity in jet spouted beds [J]. Chemical Engineering and Processing, 2005, 44(2): 153-157. 被引量:1
  • 7魏伟胜,陈恒志,徐健,石冈,鲍晓军.加压喷动床中细颗粒喷动特性[J].化工学报,2002,53(3):280-284. 被引量:9
  • 8Devahastin S, Mujumdar A S, Raghavan G S V. Hydrodynamic characteristics of a rotating jet annular spouted bed [J]. Powder Technology, 1999,103 (2): 169-174. 被引量:1
  • 9Ishikura T, Nagashima H, Ide M. Hydrodynamics of a spouted bed with a porous draft tube containing a small amount of finer particles [J]. Powder Technology, 2003, 131 (1): 56-65. 被引量:1
  • 10Takeuchi S, Wang S, Rhodes M. Discrete element simulation of a flat-bottomed spouted in the 3-D cylindrical coordinate system [J]. Chemical Engineering, Science, 2004, 59(17): 3459-3504. 被引量:1

二级参考文献43

  • 1顾燕芳,王松,胡黎明,张爱忠.超细CaCO_3合成过程中的形态控制[J].华东化工学院学报,1993,19(5):550-556. 被引量:68
  • 2徐圣言.喷动床的空气动力学特性及其结构局限性[J].农业机械学报,1996,27(4):130-135. 被引量:10
  • 3陈国桓,张健飞,陈江.从液状、膏糊状、泥团状干燥粉碎到粉末[J].化学工程,1996,24(4):17-20. 被引量:6
  • 4LINRong-yi(林荣毅) ZHANGPei-xin(张培新) ZHANGJia-yun(张家芸).The unsteady state carbonation process in synthesizing ultrafine CaCO3 particles—Ⅱ.Carbonation rate and mass transfer model(合成超微细的非稳态碳化反应过程—Ⅱ碳化速率与传质模型)[J].Engineering Chemistry & Metallurgy(化工冶金),2000,21(3):231-235. 被引量:1
  • 5Liu Yun-yi, Xu Jia-yu, Sato T, Kato K. Process for producing very fine particles by drying of salt solution in powder-particle spouted bed [A]In: Xu De-long, Mori S eds, Fluidzation 2000 Science and Technology [C]. China Xi'an: Xi'an Publishing House, 2000, 177-182. 被引量:1
  • 6ZHUTao(朱涛).[D].Fuzhou(福州):Fuzhou University(福州大学),2002. 被引量:1
  • 7CHENJian-feng(陈建峰) WANGYu-hong(王玉红) GUOKai(郭锴) GUOFen(郭奋) ZHENGChong(郑冲).Synthesis of nano—cubic CaCO3 by high—gravity reactive precipitation(超重力反应结晶法合成纳米立方形CaCO3颗粒)[J].Acta Metallurgica Sinca(金属学报),1999,35(2):179-182. 被引量:1
  • 8Juvekap VA,Sharma M M.Absorption ofCO2in a suspension oflime[J]. Chem Eng Sci,1973,28:825-837. 被引量:1
  • 9Wachi S,Jones A G. Effect of gas-liquid mass transfer on crystal size distribution during the batch precipitation of calcium carbonate[J].Chem Eng Sci,1991,46(12):3289-3293. 被引量:1
  • 10Bi H T,Can J Chem Eng,1997年,75卷,4期,460页 被引量:1

共引文献30

同被引文献35

引证文献3

二级引证文献7

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部