Multiple laser shock processing （LSP） impacts on microstructures and mechanical properties were investigated through morphological determinations and hardness testing. Microscopic results show that without equal cha...Multiple laser shock processing （LSP） impacts on microstructures and mechanical properties were investigated through morphological determinations and hardness testing. Microscopic results show that without equal channel angular pressing （ECAP）, the LSP-treated lamellar pearlite was transferred to irregular ferrite matrix and incompletely broken cementite particles. With ECAP, LSP leads to refinements of the equiaxed ferrite grain in ultrafine-grained microduplex structure from 400 to 150 nm, and the completely spheroidized cementite particles from 150 to 100 nm. Consequentially, enhancements of mechanical properties were found in strength, microhardness and elongations of samples consisting of lamellar pearlite and ultrafine-grained microduplex structure. After LSP, a mixture of quasi-cleavage and ductile fracture was formed, different from the typical quasi-cleavage fracture from the original lamellar pearlite and the ductile fracture of the microduplex structure.展开更多
The intercritical annealing treatment at 650 and 700 ℃ results in two ultrafine-grained (UFG) dual-phase ferrite-austenitesteels. The two steels exhibit different and special discontinuous yielding and pronounced L&#...The intercritical annealing treatment at 650 and 700 ℃ results in two ultrafine-grained (UFG) dual-phase ferrite-austenitesteels. The two steels exhibit different and special discontinuous yielding and pronounced Lüders-like strain phenomenawith large yielding strain which are related to their retained γ-austenite (RA) volume fractions and RA stabilities. The steelannealed at 650 ℃ shows an absent or very small strain hardening, while the steel annealed at 700 ℃ shows an obviousstrain hardening upward curvature with increasing strain. The results show that before and during straining, the steel annealedat 650 ℃ exhibits a mixture of equiaxed and elongated UFG α-ferrite and austenite phases;however, the steel annealed at700 ℃ exhibits only elongated UFG α and γ phases. It was found that most of the γ-austenite to α′-martensite transformationoccurred at the initial deformation stage and very small or almost no transformation occurred afterward. This demonstratesthat the strain-induced martensite (SIM) transformation (γ-α′) or transformation-induced plasticity (TRIP) effect dominatesonly at the initial deformation stage. RA remained stable, and no TRIP effect was observed at the final deformation stage. Theload-unload-reload test was performed to evaluate the back stress (σb) hardening effect. It is believed that the pronouncedstrain hardening behavior at the later deformation stage is mainly associated with σb enhancement induced by the strainpartitioning between the soft and hard phases due to SIM transformation during tensile deformation.展开更多
Surface microstructure and microhardness of （ferrite＋ cementite） microduplex structure of the ultrafine- grained high carbon steel after laser shock processing （LSP） with different impact times were investigated ...Surface microstructure and microhardness of （ferrite＋ cementite） microduplex structure of the ultrafine- grained high carbon steel after laser shock processing （LSP） with different impact times were investigated by means of scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, X-ray diffraction （XRD） and microhardness measurements. Equiaxed ferrite grains were refined from 400 to 150 nm, and the cementite lamellae were fully spheroidized, with a decrease of the particle diameter from 150 to 100 nm as the impact times increased. The cementite dissolution was enhanced significantly. Correspondingly, the lattice parameter of α-Fe and microhard- hess increased with the impact times.展开更多
An ultrafine-grained(UFG) low-carbon medium-manganese steel was fabricated by the heavily warm rolling(HWR) and subsequent quenching, and the effects of annealing temperatures on microstructure and mechanical properti...An ultrafine-grained(UFG) low-carbon medium-manganese steel was fabricated by the heavily warm rolling(HWR) and subsequent quenching, and the effects of annealing temperatures on microstructure and mechanical properties of the UFG HWRed steel were investigated. The results show that the HWRed steel exhibits simultaneous improvements in strength,uniform elongation and work hardening, which is mainly attributed to the refinement of martensitic microstructures. The HWRed steels comprise only a-phase when annealing at lower temperatures below to 550 °C and at higher temperatures above to 700 °C. Whereas, UFG c-austenite is formed by reverse transformation when the HWRed steel was annealed at intermediate temperatures from 550 to 700 °C and the volume fraction increases with increasing annealing temperatures,consequently resulting in a dramatic increase in ductility of the annealed HWRed steels. It was found that the transformed UFG austenite and ferrite remained ～500 nm and ～800 nm in size when the HWRed steel was annealed at 650 and700 °C for 1 h, respectively, showing an excellent thermal stability. Moreover, the HWRed steel annealed at 650 °C exhibits high strength-ductility combinations with a yield strength of 906 MPa, ultimate tensile strength(UTS) of1011 MPa, total elongation(TEL) of 51% and product of strength and elongation(PSE: UTS 9 TEL) of 52 GPa%. It is believed that these excellent comprehensive mechanical properties are closely associated with the UFG austenite formation by reverse transformation and principally attributed to the transformation-induced plasticity(TRIP) effect.展开更多
304 austenitic stainless steel was cold rolled in the range of 20%-80%reductions and then annealed at 700-900°C for 60 sto obtain nano/ultrafine-grained（NG/UFG）structure.Transmission electron microscopy,electro...304 austenitic stainless steel was cold rolled in the range of 20%-80%reductions and then annealed at 700-900°C for 60 sto obtain nano/ultrafine-grained（NG/UFG）structure.Transmission electron microscopy,electron backscatter diffraction and X-ray diffraction were used to characterize the resulting microstructures.The results showed that with the increase of cold reduction,the content of martensite was increased.The steel performed work hardening during cold-working owing to the occurrence of strain induced martensite which nucleated in single shear bands.Further rolling broke up the lath-type martensite into dislocation-cell type martensite because of the formation of slip bands.Samples annealed at 800-960°C for 60 swere of NG/UFG structure with different percentage of nanocrystalline（60-100 nm）and ultrafine（100-500 nm）grains,submicron size（500-1000 nm）grains and micron size（〉1000 nm）grains.The value of the Gibbs free energy exhibited that the reversion mechanism of the reversion process was shear controlled by the annealing temperature.For a certain annealing time during the reversion process,austenite nucleated first on dislocation-cell type martensite and the grains grew up subsequently and eventually to be micrometer/submicrometer grains,while the nucleation of austenite on lath-type martensite occurred later resulting in nanocrystalline/ultrafine grains.The existence of the NG/UFG structure led to a higher strength and toughness during tensile test.展开更多
3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is l...3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.展开更多
文摘Multiple laser shock processing （LSP） impacts on microstructures and mechanical properties were investigated through morphological determinations and hardness testing. Microscopic results show that without equal channel angular pressing （ECAP）, the LSP-treated lamellar pearlite was transferred to irregular ferrite matrix and incompletely broken cementite particles. With ECAP, LSP leads to refinements of the equiaxed ferrite grain in ultrafine-grained microduplex structure from 400 to 150 nm, and the completely spheroidized cementite particles from 150 to 100 nm. Consequentially, enhancements of mechanical properties were found in strength, microhardness and elongations of samples consisting of lamellar pearlite and ultrafine-grained microduplex structure. After LSP, a mixture of quasi-cleavage and ductile fracture was formed, different from the typical quasi-cleavage fracture from the original lamellar pearlite and the ductile fracture of the microduplex structure.
基金supported by the Joint Research Center for Future Iron and Steel,SJTU&BaosteelThe author(L.M.Fu)is grateful to the financial support from Startup Fund for Youngman Research at SJTU(SFYR at SJTU,No.18X100040023).
文摘The intercritical annealing treatment at 650 and 700 ℃ results in two ultrafine-grained (UFG) dual-phase ferrite-austenitesteels. The two steels exhibit different and special discontinuous yielding and pronounced Lüders-like strain phenomenawith large yielding strain which are related to their retained γ-austenite (RA) volume fractions and RA stabilities. The steelannealed at 650 ℃ shows an absent or very small strain hardening, while the steel annealed at 700 ℃ shows an obviousstrain hardening upward curvature with increasing strain. The results show that before and during straining, the steel annealedat 650 ℃ exhibits a mixture of equiaxed and elongated UFG α-ferrite and austenite phases;however, the steel annealed at700 ℃ exhibits only elongated UFG α and γ phases. It was found that most of the γ-austenite to α′-martensite transformationoccurred at the initial deformation stage and very small or almost no transformation occurred afterward. This demonstratesthat the strain-induced martensite (SIM) transformation (γ-α′) or transformation-induced plasticity (TRIP) effect dominatesonly at the initial deformation stage. RA remained stable, and no TRIP effect was observed at the final deformation stage. Theload-unload-reload test was performed to evaluate the back stress (σb) hardening effect. It is believed that the pronouncedstrain hardening behavior at the later deformation stage is mainly associated with σb enhancement induced by the strainpartitioning between the soft and hard phases due to SIM transformation during tensile deformation.
基金Sponsored by National Natural Science Foundation of China(50801021,51201061)Program for Young Key Teachers in Henan Province of China(2011GGJS-070)Program for Henan Province for Science and Technology Innovation Excellent Talents of China(144200510001)
文摘Surface microstructure and microhardness of （ferrite＋ cementite） microduplex structure of the ultrafine- grained high carbon steel after laser shock processing （LSP） with different impact times were investigated by means of scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, X-ray diffraction （XRD） and microhardness measurements. Equiaxed ferrite grains were refined from 400 to 150 nm, and the cementite lamellae were fully spheroidized, with a decrease of the particle diameter from 150 to 100 nm as the impact times increased. The cementite dissolution was enhanced significantly. Correspondingly, the lattice parameter of α-Fe and microhard- hess increased with the impact times.
基金financially supported by the National Major Science and Technology Project of China (No. 2014ZX07214-002)
文摘An ultrafine-grained(UFG) low-carbon medium-manganese steel was fabricated by the heavily warm rolling(HWR) and subsequent quenching, and the effects of annealing temperatures on microstructure and mechanical properties of the UFG HWRed steel were investigated. The results show that the HWRed steel exhibits simultaneous improvements in strength,uniform elongation and work hardening, which is mainly attributed to the refinement of martensitic microstructures. The HWRed steels comprise only a-phase when annealing at lower temperatures below to 550 °C and at higher temperatures above to 700 °C. Whereas, UFG c-austenite is formed by reverse transformation when the HWRed steel was annealed at intermediate temperatures from 550 to 700 °C and the volume fraction increases with increasing annealing temperatures,consequently resulting in a dramatic increase in ductility of the annealed HWRed steels. It was found that the transformed UFG austenite and ferrite remained ～500 nm and ～800 nm in size when the HWRed steel was annealed at 650 and700 °C for 1 h, respectively, showing an excellent thermal stability. Moreover, the HWRed steel annealed at 650 °C exhibits high strength-ductility combinations with a yield strength of 906 MPa, ultimate tensile strength(UTS) of1011 MPa, total elongation(TEL) of 51% and product of strength and elongation(PSE: UTS 9 TEL) of 52 GPa%. It is believed that these excellent comprehensive mechanical properties are closely associated with the UFG austenite formation by reverse transformation and principally attributed to the transformation-induced plasticity(TRIP) effect.
基金supported by the National Natural Science Foundation of China(Grant No.51474031)
文摘304 austenitic stainless steel was cold rolled in the range of 20%-80%reductions and then annealed at 700-900°C for 60 sto obtain nano/ultrafine-grained（NG/UFG）structure.Transmission electron microscopy,electron backscatter diffraction and X-ray diffraction were used to characterize the resulting microstructures.The results showed that with the increase of cold reduction,the content of martensite was increased.The steel performed work hardening during cold-working owing to the occurrence of strain induced martensite which nucleated in single shear bands.Further rolling broke up the lath-type martensite into dislocation-cell type martensite because of the formation of slip bands.Samples annealed at 800-960°C for 60 swere of NG/UFG structure with different percentage of nanocrystalline（60-100 nm）and ultrafine（100-500 nm）grains,submicron size（500-1000 nm）grains and micron size（〉1000 nm）grains.The value of the Gibbs free energy exhibited that the reversion mechanism of the reversion process was shear controlled by the annealing temperature.For a certain annealing time during the reversion process,austenite nucleated first on dislocation-cell type martensite and the grains grew up subsequently and eventually to be micrometer/submicrometer grains,while the nucleation of austenite on lath-type martensite occurred later resulting in nanocrystalline/ultrafine grains.The existence of the NG/UFG structure led to a higher strength and toughness during tensile test.
基金This work was supported by the‘973'ScienceTechnology Development Plan of the National Basic Research Foundation(No.1998061500)the 985'Foundation of Tsinghua University.
文摘3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.
