A low carbon Nb-Ti microalloyed steel was subjected to hot torsion testing over the temperature range 850-1100℃ and strain rates 0.01-1 s-1 to study the influence of deformation conditions on the dynamic recrystalliz...A low carbon Nb-Ti microalloyed steel was subjected to hot torsion testing over the temperature range 850-1100℃ and strain rates 0.01-1 s-1 to study the influence of deformation conditions on the dynamic recrystallization characteristics of austenite. The results show that dynamic recrystallization occurs more easily with the decrease of strain rate and the increase of deformation temperature. The complete dynamically recrystallized grain size as a function of Zener-Hollomon parameter was established. It was found that dynamically recrystallized grain sizes decrease with increasing strain rate and decreasing deformation temperature. The effect of microalloying elements on peak strain was investigated and the solute drag corrected peak strain was determined. Also, the dynamic recrystallization map of austenite was obtained by using recrystallization critical parameters.展开更多
Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched...Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched. The study indicates that the dynamicrecrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter(Zener-Hollmon Parameter), i.e. 19.3 <= lnZ <=24.8. Increasing the strain rate at higher deformationtemperature or reducing the strain rate at lower deformation temperature accelerates the occurrenceof dynamic recrystallization in the alloy.展开更多
Hot torsion testing was performed on a low carbon Nb-Ti microalloyed steel to study the effects of hot tor- sion parameters, strain and strain rate, on ultrafine ferrite grains production through dynamic strain-induce...Hot torsion testing was performed on a low carbon Nb-Ti microalloyed steel to study the effects of hot tor- sion parameters, strain and strain rate, on ultrafine ferrite grains production through dynamic strain-induced trans- formation, at a deformation temperature just above At3. The initiation and evolution of ultrafine ferrite grains were studied. The results show that the amount of strain and strain rate has conversely effect on the volume fraction and grain size of ultrafine ferrite grains. With increasing strain, the interior of austenite grains become activated as nucle- ation sites for fine ferrite grains. As a result, ferrite grains continuously nucleate not only at the former austenite grain boundaries but also inside the austenite grains which leads to a rapid increase in volume fraction of ultrafine grains. Increasing of strain rate reduces the tendency of ferrite grains coarsening so that ultrafine ferrite grains are achieved, while the volume fraction of ultrafine grains decreases at the same strain level.展开更多
The commercial finite element package ANSYSTM was utilized for prediction of temperature distribution during reheating treatment of hot torsion test （HTT） samples with different geometries for API-X70 microalloyed s...The commercial finite element package ANSYSTM was utilized for prediction of temperature distribution during reheating treatment of hot torsion test （HTT） samples with different geometries for API-X70 microalloyed steel. Simulation results show that an inappropriate choice of test specimen geometry and reheating conditions before deformation could lead to non-uniform temperature distribution within the gauge section of specimen. Therefore, assumptions of isothermal experimental conditions and zero temperature gradient within the specimen cross section appear unjustified and led to uncertainties of flow curve obtained. Recommendations on finding proper specimen geometry for reducing temperature gradient along the gauge part of specimen will be given to create homogeneous initial microstructure as much as possible before deformation in order to avoid uncertainty in consequent results of HTT.展开更多
文摘A low carbon Nb-Ti microalloyed steel was subjected to hot torsion testing over the temperature range 850-1100℃ and strain rates 0.01-1 s-1 to study the influence of deformation conditions on the dynamic recrystallization characteristics of austenite. The results show that dynamic recrystallization occurs more easily with the decrease of strain rate and the increase of deformation temperature. The complete dynamically recrystallized grain size as a function of Zener-Hollomon parameter was established. It was found that dynamically recrystallized grain sizes decrease with increasing strain rate and decreasing deformation temperature. The effect of microalloying elements on peak strain was investigated and the solute drag corrected peak strain was determined. Also, the dynamic recrystallization map of austenite was obtained by using recrystallization critical parameters.
基金The project was sponsored by the Education Administration Major Project for Science Research under the contract No. 99134.
文摘Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched. The study indicates that the dynamicrecrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter(Zener-Hollmon Parameter), i.e. 19.3 <= lnZ <=24.8. Increasing the strain rate at higher deformationtemperature or reducing the strain rate at lower deformation temperature accelerates the occurrenceof dynamic recrystallization in the alloy.
基金financially supported by the Natural Science Foundation of Chongqing,China(No.cstc2021jcyj-msxm X0433)the Chongqing Foundation of Science and Technology,China(Nos.cstc2020jxjl X0001,cstc2021jxjl50004)the National Natural Science Foundation of China(No.51601154)。
文摘Hot torsion testing was performed on a low carbon Nb-Ti microalloyed steel to study the effects of hot tor- sion parameters, strain and strain rate, on ultrafine ferrite grains production through dynamic strain-induced trans- formation, at a deformation temperature just above At3. The initiation and evolution of ultrafine ferrite grains were studied. The results show that the amount of strain and strain rate has conversely effect on the volume fraction and grain size of ultrafine ferrite grains. With increasing strain, the interior of austenite grains become activated as nucle- ation sites for fine ferrite grains. As a result, ferrite grains continuously nucleate not only at the former austenite grain boundaries but also inside the austenite grains which leads to a rapid increase in volume fraction of ultrafine grains. Increasing of strain rate reduces the tendency of ferrite grains coarsening so that ultrafine ferrite grains are achieved, while the volume fraction of ultrafine grains decreases at the same strain level.
文摘The commercial finite element package ANSYSTM was utilized for prediction of temperature distribution during reheating treatment of hot torsion test （HTT） samples with different geometries for API-X70 microalloyed steel. Simulation results show that an inappropriate choice of test specimen geometry and reheating conditions before deformation could lead to non-uniform temperature distribution within the gauge section of specimen. Therefore, assumptions of isothermal experimental conditions and zero temperature gradient within the specimen cross section appear unjustified and led to uncertainties of flow curve obtained. Recommendations on finding proper specimen geometry for reducing temperature gradient along the gauge part of specimen will be given to create homogeneous initial microstructure as much as possible before deformation in order to avoid uncertainty in consequent results of HTT.
