This study, taking three types of aluminum alloys 2024-T351, 6061-T6 and 7075-T6 as experimental materials, conducted single V-groove GTAW （gas tungsten arc welding） butt-welding to analyze and compare the magnitude...This study, taking three types of aluminum alloys 2024-T351, 6061-T6 and 7075-T6 as experimental materials, conducted single V-groove GTAW （gas tungsten arc welding） butt-welding to analyze and compare the magnitude and differences of residual stress in the three aluminum alloys at different single V-groove angles and in restrained or unrestrained conditions. The results show that the larger the grooving angle of butt joint, the higher the residual tensile stress. Too small grooving angle will lead to dramatic differences due to the amount of welding bead filler metal and pre-set joint geometry. Therefore, only an appropriate grooving angle can reduce residual stress. While welding, weldment in restrained condition will lead to a larger residual stress. Also, a residual stress will arise from the restraint position. The ultimate residual stress of weldment is determined by material yield strength at equilibrium temperature. The higher the yield strength at equilibrium temperature, the higher the material residual stress. Because of its larger thermal conductivity, aluminum alloy test specimens have small temperature differential. Therefore, the residual tensile stress of all materials is lower than their yield strength.展开更多
The hole-drilling method is one of the most wellknown methods for measuring residual stresses. To identify unknown plane stresses in a specimen, a circular hole is first drilled in the infinite plate under plane stres...The hole-drilling method is one of the most wellknown methods for measuring residual stresses. To identify unknown plane stresses in a specimen, a circular hole is first drilled in the infinite plate under plane stress, then the strains resulting from the hole drilling is measured. The strains may be acquired from interpreting the Moire signature around the hole. In crossed grating Moire interferometry, the horizontal and vertical displacement fields （u and v） can be obtained to determinate two strain fields and one shearing strain field. In this paper, by means of Moire interferometry and three directions grating （grating rosette） developed by the authors, three displacement fields （u, v and s） are obtained to acquire three strain fields. As a practical application, the hole-drilling method is adopted to measure the relief strains for aluminum and fiber reinforced composite. It is a step by step method; in each step a single laminate or equivalent depth is drilled to find some relationships between the drilling depth and the residual strains relieved in the fiber reinforced composite materials.展开更多
Residual stress evolution regularity in thermal barrier ceramic coatings （TBCs） under different cycles of thermal shock loading of 1 100℃ was investi- gated by the microscopic digital image correlation （DIC） and ...Residual stress evolution regularity in thermal barrier ceramic coatings （TBCs） under different cycles of thermal shock loading of 1 100℃ was investi- gated by the microscopic digital image correlation （DIC） and micro-Raman spec- troscopy, respectively. The obtained results showed that, as the cycle number of the thermal shock loading increases, the evolution of the residual stress under- goes three distinct stages： a sharp increase, a gradual change, and a reduction. The extension stress near the TBC surface is fast transformed to compressive one through just one thermal cycle. After different thermal shock cycles with peak temperature of 1 100℃, phase transformation in TBC does not happen, whereas the generation, development, evolution of the thermally grown oxide （TGO） layer and micro-cracks are the main reasons causing the evolution regularity of the residual stress.展开更多
Residual stresses in ion-implanted NiTi alloy are measured by a combined method ofMoir6 interferometry and hole-drilling. Oxygen ions are implanted into the NiTi alloy under a voltage of 30 kV by a dose of 1.0×10...Residual stresses in ion-implanted NiTi alloy are measured by a combined method ofMoir6 interferometry and hole-drilling. Oxygen ions are implanted into the NiTi alloy under a voltage of 30 kV by a dose of 1.0×10^17ions/cm^2 for one hour. Subsequently, in order to avoid dimensional error, a hole is drilled exactly in the center of the sample. The distribution of residual stresses around the hole is measured. It is indicated that the method which combines the Moire interferometry with hole-drilling is able to be used to measure residual stresses produced by ion implantation.展开更多
Hole-drilling method is a commonly used method for measuring residual stress. The calibration coefficients in ASTM E837-13 a would cause large errors due to the plasticity deformation of materials. In the study, calib...Hole-drilling method is a commonly used method for measuring residual stress. The calibration coefficients in ASTM E837-13 a would cause large errors due to the plasticity deformation of materials. In the study, calibration coefficients were modified in the plasticity deformation stage based on the distortion energy theory. The calibration experiment of calibration coefficients was simulated by the finite element model, and the plasticity modification formulas of 7075 aluminum alloy were obtained. From the results of uniaxial tensile loading test, the measuring errors of high residual stress are significantly reduced from-4.071%～53.440% to-5.140% ～ 0.609% after the plasticity modification. This work provides an effective way to expand the application of hole-drilling method.展开更多
This paper investigates an advanced grating-transferring technique combined with geometric phase analysis (GPA) for residual strain evaluation of curved surface.A standard holographic grating is first transferred to a...This paper investigates an advanced grating-transferring technique combined with geometric phase analysis (GPA) for residual strain evaluation of curved surface.A standard holographic grating is first transferred to a pre-produced epoxy resin film and then consolidated to a test region of curved surface.With a rubber mold and silicone rubber the deformed grating is replicated to a sheet metal after hole-drilling for release of residual stress.After that the grating is transferred from the sheet metal to the glass plate,which would be served as an analyzer grating (specimen grating).By GPA the local strain distributions related to the phase difference between the reference grating and analyzer grating for the released stress can be evaluated.A validation test has been conducted on the weld joint of a stainless steel tube and the obtained results demonstrate the ability of the method in measuring the residual strain of curved surface.展开更多
This paper investigates the effect of the location of testing area in residual stress measurement by Moiréinterferometry combined with hole-drilling method.The selection of the location of the testing area is ana...This paper investigates the effect of the location of testing area in residual stress measurement by Moiréinterferometry combined with hole-drilling method.The selection of the location of the testing area is analyzed from theory and experiment.In the theoretical study,the factors which affect the surface released radial strainεr were analyzed on the basis of the formulae of the hole-drilling method,and the relations between those factors andεr were established.By combining Moiréinterferometry with the hole-drilling method,the residual stress of interference-fit specimen was measured to verify the theoretical analysis.According to the analysis results,the testing area for minimizing the error of strain measurement is determined.Moreover,if the orientation of the maximum principal stress is known,the value of strain will be measured with higher precision by the Moiréinterferometry method.展开更多
文摘This study, taking three types of aluminum alloys 2024-T351, 6061-T6 and 7075-T6 as experimental materials, conducted single V-groove GTAW （gas tungsten arc welding） butt-welding to analyze and compare the magnitude and differences of residual stress in the three aluminum alloys at different single V-groove angles and in restrained or unrestrained conditions. The results show that the larger the grooving angle of butt joint, the higher the residual tensile stress. Too small grooving angle will lead to dramatic differences due to the amount of welding bead filler metal and pre-set joint geometry. Therefore, only an appropriate grooving angle can reduce residual stress. While welding, weldment in restrained condition will lead to a larger residual stress. Also, a residual stress will arise from the restraint position. The ultimate residual stress of weldment is determined by material yield strength at equilibrium temperature. The higher the yield strength at equilibrium temperature, the higher the material residual stress. Because of its larger thermal conductivity, aluminum alloy test specimens have small temperature differential. Therefore, the residual tensile stress of all materials is lower than their yield strength.
基金the National Natural Science Foundation of China (10772117, 10572089)
文摘The hole-drilling method is one of the most wellknown methods for measuring residual stresses. To identify unknown plane stresses in a specimen, a circular hole is first drilled in the infinite plate under plane stress, then the strains resulting from the hole drilling is measured. The strains may be acquired from interpreting the Moire signature around the hole. In crossed grating Moire interferometry, the horizontal and vertical displacement fields （u and v） can be obtained to determinate two strain fields and one shearing strain field. In this paper, by means of Moire interferometry and three directions grating （grating rosette） developed by the authors, three displacement fields （u, v and s） are obtained to acquire three strain fields. As a practical application, the hole-drilling method is adopted to measure the relief strains for aluminum and fiber reinforced composite. It is a step by step method; in each step a single laminate or equivalent depth is drilled to find some relationships between the drilling depth and the residual strains relieved in the fiber reinforced composite materials.
基金supported by the National Natural Science Foundation of China(91216301,11072033,11232008,and 11372037)the Program for New Century Excellent Talents in University(NCET-12-0036)the Natural Science Foundation of Beijing,China(3122027)
文摘Residual stress evolution regularity in thermal barrier ceramic coatings （TBCs） under different cycles of thermal shock loading of 1 100℃ was investi- gated by the microscopic digital image correlation （DIC） and micro-Raman spec- troscopy, respectively. The obtained results showed that, as the cycle number of the thermal shock loading increases, the evolution of the residual stress under- goes three distinct stages： a sharp increase, a gradual change, and a reduction. The extension stress near the TBC surface is fast transformed to compressive one through just one thermal cycle. After different thermal shock cycles with peak temperature of 1 100℃, phase transformation in TBC does not happen, whereas the generation, development, evolution of the thermally grown oxide （TGO） layer and micro-cracks are the main reasons causing the evolution regularity of the residual stress.
基金National Natural Science Foundation of China (10572155)
文摘Residual stresses in ion-implanted NiTi alloy are measured by a combined method ofMoir6 interferometry and hole-drilling. Oxygen ions are implanted into the NiTi alloy under a voltage of 30 kV by a dose of 1.0×10^17ions/cm^2 for one hour. Subsequently, in order to avoid dimensional error, a hole is drilled exactly in the center of the sample. The distribution of residual stresses around the hole is measured. It is indicated that the method which combines the Moire interferometry with hole-drilling is able to be used to measure residual stresses produced by ion implantation.
基金supported by the Natural Science Foundation of Fujian Provinceof China(No.2018J01082)the China Scholarship Council(No.201806315006)the National Natural Science Foundation of China(No.51305371)
文摘Hole-drilling method is a commonly used method for measuring residual stress. The calibration coefficients in ASTM E837-13 a would cause large errors due to the plasticity deformation of materials. In the study, calibration coefficients were modified in the plasticity deformation stage based on the distortion energy theory. The calibration experiment of calibration coefficients was simulated by the finite element model, and the plasticity modification formulas of 7075 aluminum alloy were obtained. From the results of uniaxial tensile loading test, the measuring errors of high residual stress are significantly reduced from-4.071%～53.440% to-5.140% ～ 0.609% after the plasticity modification. This work provides an effective way to expand the application of hole-drilling method.
基金supported by the National Natural Science Foundation of China (11072033 and 90916010)Specialized Research Fund for the Doctoral Program of Higher Education (20090002110048)
文摘This paper investigates an advanced grating-transferring technique combined with geometric phase analysis (GPA) for residual strain evaluation of curved surface.A standard holographic grating is first transferred to a pre-produced epoxy resin film and then consolidated to a test region of curved surface.With a rubber mold and silicone rubber the deformed grating is replicated to a sheet metal after hole-drilling for release of residual stress.After that the grating is transferred from the sheet metal to the glass plate,which would be served as an analyzer grating (specimen grating).By GPA the local strain distributions related to the phase difference between the reference grating and analyzer grating for the released stress can be evaluated.A validation test has been conducted on the weld joint of a stainless steel tube and the obtained results demonstrate the ability of the method in measuring the residual strain of curved surface.
基金supported by the National Basic Research Program of China(Grant Nos.2010CB631005 and 2011CB606105)the National Natural Science Foundation of China(Grant Nos.11232008,91216301,11227801 and 11172151)Tsinghua University Initiative Scientific Research Program
文摘This paper investigates the effect of the location of testing area in residual stress measurement by Moiréinterferometry combined with hole-drilling method.The selection of the location of the testing area is analyzed from theory and experiment.In the theoretical study,the factors which affect the surface released radial strainεr were analyzed on the basis of the formulae of the hole-drilling method,and the relations between those factors andεr were established.By combining Moiréinterferometry with the hole-drilling method,the residual stress of interference-fit specimen was measured to verify the theoretical analysis.According to the analysis results,the testing area for minimizing the error of strain measurement is determined.Moreover,if the orientation of the maximum principal stress is known,the value of strain will be measured with higher precision by the Moiréinterferometry method.
