采用不同质量分数的NH_4NO_3和(NH_4)_2S_2O_8溶液作为电解液,对双室微生物燃料电池的阳极炭布进行改性。以餐厨废水作为阳极底物,以K_3[Fe(CN)_6]和NaCl混合溶液为阴极液,考察不同电解液改性阳极条件下微生物燃料电池的产电性能及污水...采用不同质量分数的NH_4NO_3和(NH_4)_2S_2O_8溶液作为电解液,对双室微生物燃料电池的阳极炭布进行改性。以餐厨废水作为阳极底物,以K_3[Fe(CN)_6]和NaCl混合溶液为阴极液,考察不同电解液改性阳极条件下微生物燃料电池的产电性能及污水处理效果。结果表明,采用NH_4NO_3或(NH_4)_2S_2O_8改性炭布作为阳极的微生物燃料电池的发电性能和水处理效果均有改善。其中,采用质量分数为4%的(NH_4)_2S_2O_8溶液作为阳极改性电解液时,微生物燃料电池系统的产电性能达到最佳,其稳态电流密度约为60 m A/m^2,COD去除率约为42.5%。展开更多
LiNiCoAlO（NCA） with Zr（OH）coating is demonstrated as high performance cathode material for lithium ion batteries（LIBs）. The coated materials are synthesized via a simple dry coating method of NCA with Zr（OH）po...LiNiCoAlO（NCA） with Zr（OH）coating is demonstrated as high performance cathode material for lithium ion batteries（LIBs）. The coated materials are synthesized via a simple dry coating method of NCA with Zr（OH）powders, and then characterized with scanning electron microscopy（SEM）, transmission electron microscopy（TEM） and X-ray photoelectron spectroscopy（XPS）. Experimental results show that amorphous Zr（OH）powders have been successfully coated on the surface of spherical NCA particles, exhibiting improved electrochemical performance. 0.50 wt% Zr（OH）coated NCA delivers a capacity of 197.6 mAh/g at the first cycle and 154.3 mAh/g after 100 cycles with a capacity retention of 78.1% at 1 C rate. In comparison, the pure NCA shows a capacity of 194.6 mAh/g at the first cycle and 142.5 mAh/g after 100 cycles with a capacity retention of 73.2% at 1 C rate. Electrochemical impedance spectroscopy（EIS） results show that the coated material exhibits a lower resistance, indicating that the coating layer can efficiently suppress transition metals dissolution and decrease the side reactions at the surface between the electrode and electrolyte. Therefore, surface coating with amorphous Zr（OH）is a simple and useful method to enhance the electrochemical performance of NCA-based materials for the cathode of LIBs.展开更多
通过多种电化学测试技术评价了石墨电极在2.3 mol/L H2SO4溶液中的电化学活化工艺及其准电容性能。结果表明,活化工艺宜采用恒电流阶跃技术,最佳工艺参数为:阳极电流密度为200 m A·cm-2,阴极电流密度为-120 m A·cm-2,对应活...通过多种电化学测试技术评价了石墨电极在2.3 mol/L H2SO4溶液中的电化学活化工艺及其准电容性能。结果表明,活化工艺宜采用恒电流阶跃技术,最佳工艺参数为:阳极电流密度为200 m A·cm-2,阴极电流密度为-120 m A·cm-2,对应活化时间分别为300 s和100 s,循环6次。改性后的石墨电极表面形成了多孔、粗糙的三维活性层,单位面积上具有较高的电容量(2.08 F·cm-2)和良好的倍率特性,可作为一种优异的准电容器材料。展开更多
Superhydrophobic aluminum surfaces have been prepared by means of electrodeposition of copper on aluminum surfaces, followed by electrochemical modification using stearic acid organic molecules. Scanning electron micr...Superhydrophobic aluminum surfaces have been prepared by means of electrodeposition of copper on aluminum surfaces, followed by electrochemical modification using stearic acid organic molecules. Scanning electron microscopy(SEM) images show that the electrodeposited copper films follow "island growth mode" in the form of microdots and their number densities increase with the rise of the negative deposition potentials. At an electrodeposition potential of-0.2 V the number density of the copper microdots are found to be 4.5×104cm^(-2)that are increased to 2.9×105cm^(-2)at a potential of-0.8 V. Systematically, the distances between the microdots are found to be reduced from 26.6 μm to 11.03 μm with the increase of negative electrochemical potential from-0.2 V to-0.8 V. X-ray diffraction(XRD) analyses have confirmed the formation of copper stearate on the stearic acid modified copper films. The roughness of the stearic acid modified electrodeposited copper films is found to increase with the increase in the density of the copper microdots. A critical copper deposition potential of-0.6 V in conjunction with the stearic acid modification provides a surface roughness of 6.2 μm with a water contact angle of 157?, resulting in superhydrophobic properties on the aluminum substrates.展开更多
文摘采用不同质量分数的NH_4NO_3和(NH_4)_2S_2O_8溶液作为电解液,对双室微生物燃料电池的阳极炭布进行改性。以餐厨废水作为阳极底物,以K_3[Fe(CN)_6]和NaCl混合溶液为阴极液,考察不同电解液改性阳极条件下微生物燃料电池的产电性能及污水处理效果。结果表明,采用NH_4NO_3或(NH_4)_2S_2O_8改性炭布作为阳极的微生物燃料电池的发电性能和水处理效果均有改善。其中,采用质量分数为4%的(NH_4)_2S_2O_8溶液作为阳极改性电解液时,微生物燃料电池系统的产电性能达到最佳,其稳态电流密度约为60 m A/m^2,COD去除率约为42.5%。
基金supported by the National Projects of NSFC(21322101 and 21231005)MOE(B12015 and IRT13R30)
文摘LiNiCoAlO（NCA） with Zr（OH）coating is demonstrated as high performance cathode material for lithium ion batteries（LIBs）. The coated materials are synthesized via a simple dry coating method of NCA with Zr（OH）powders, and then characterized with scanning electron microscopy（SEM）, transmission electron microscopy（TEM） and X-ray photoelectron spectroscopy（XPS）. Experimental results show that amorphous Zr（OH）powders have been successfully coated on the surface of spherical NCA particles, exhibiting improved electrochemical performance. 0.50 wt% Zr（OH）coated NCA delivers a capacity of 197.6 mAh/g at the first cycle and 154.3 mAh/g after 100 cycles with a capacity retention of 78.1% at 1 C rate. In comparison, the pure NCA shows a capacity of 194.6 mAh/g at the first cycle and 142.5 mAh/g after 100 cycles with a capacity retention of 73.2% at 1 C rate. Electrochemical impedance spectroscopy（EIS） results show that the coated material exhibits a lower resistance, indicating that the coating layer can efficiently suppress transition metals dissolution and decrease the side reactions at the surface between the electrode and electrolyte. Therefore, surface coating with amorphous Zr（OH）is a simple and useful method to enhance the electrochemical performance of NCA-based materials for the cathode of LIBs.
文摘通过多种电化学测试技术评价了石墨电极在2.3 mol/L H2SO4溶液中的电化学活化工艺及其准电容性能。结果表明,活化工艺宜采用恒电流阶跃技术,最佳工艺参数为:阳极电流密度为200 m A·cm-2,阴极电流密度为-120 m A·cm-2,对应活化时间分别为300 s和100 s,循环6次。改性后的石墨电极表面形成了多孔、粗糙的三维活性层,单位面积上具有较高的电容量(2.08 F·cm-2)和良好的倍率特性,可作为一种优异的准电容器材料。
基金the financial support provided by the Natural Sciences and Engineering Research Council of Canada(NSERC)
文摘Superhydrophobic aluminum surfaces have been prepared by means of electrodeposition of copper on aluminum surfaces, followed by electrochemical modification using stearic acid organic molecules. Scanning electron microscopy(SEM) images show that the electrodeposited copper films follow "island growth mode" in the form of microdots and their number densities increase with the rise of the negative deposition potentials. At an electrodeposition potential of-0.2 V the number density of the copper microdots are found to be 4.5×104cm^(-2)that are increased to 2.9×105cm^(-2)at a potential of-0.8 V. Systematically, the distances between the microdots are found to be reduced from 26.6 μm to 11.03 μm with the increase of negative electrochemical potential from-0.2 V to-0.8 V. X-ray diffraction(XRD) analyses have confirmed the formation of copper stearate on the stearic acid modified copper films. The roughness of the stearic acid modified electrodeposited copper films is found to increase with the increase in the density of the copper microdots. A critical copper deposition potential of-0.6 V in conjunction with the stearic acid modification provides a surface roughness of 6.2 μm with a water contact angle of 157?, resulting in superhydrophobic properties on the aluminum substrates.
