An adjustable mixer for surface acoustic wave( SAW)-less radio frequency( RF) front-end is presented in this paper. Through changing the bias voltage,the presented mixer with reconfigurable voltage conversion gain( VC...An adjustable mixer for surface acoustic wave( SAW)-less radio frequency( RF) front-end is presented in this paper. Through changing the bias voltage,the presented mixer with reconfigurable voltage conversion gain( VCG) is suitable for multi-mode multi-standard( MMMS) applications. An equivalent local oscillator( LO) frequency-tunable high-Q band-pass filter( BPF) at low noise amplifier( LNA) output is used to reject the out-of-band interference signals. Base-band( BB) capacitor of the mixer is variable to obtain 15 kinds of intermediate frequency( IF) bandwidth( BW). The proposed passive mixer with LNA is implemented in TSMC 0. 18μm RF CMOS process and operates from 0. 5 to 2. 5 GHz with measured maximum out-of-band rejection larger than 40 d B. The measured VCG of the front-end can be changed from 5 to 17 d B; the maximum input intercept point( IIP3) is0 d Bm and the minimum noise figure( NF) is 3. 7 d B. The chip occupies an area of 0. 44 mm^2 including pads.展开更多
This paper describes a novel divide-by-32/33 dual-modulus prescaler （DMP）. Here, a new combination of DFF has been introduced in the DMP. By means of the cooperation and coordination among three types, DFF, SCL, TPS...This paper describes a novel divide-by-32/33 dual-modulus prescaler （DMP）. Here, a new combination of DFF has been introduced in the DMP. By means of the cooperation and coordination among three types, DFF, SCL, TPSC, and CMOS static flip-flop, the DMP demonstrates high speed, wideband, and low power consumption with low phase noise. The chip has been fabricated in a 0.18μm CMOS process of SMIC. The measured results show that the DMP＇s operating frequency is from 0.9 to 3.4 GHz with a maximum power consumption of 2.51 mW under a 1.8 V power supply and the phase noise is -134.78 dBc/Hz at 1 MHz offset from the 3.4 GHz carrier. The core area of the die without PAD is 57 x 30 #m2. Due to its excellent performance, the DMP could be applied to a PLL-based frequency synthesizer for many RF systems, especially for multi-standard radio applications.展开更多
A low power fast settling multi-standard CMOS fractional-N frequency synthesizer is proposed. The current reusing and frequency presetting techniques are adopted to realize the low power fast settling multi-standard f...A low power fast settling multi-standard CMOS fractional-N frequency synthesizer is proposed. The current reusing and frequency presetting techniques are adopted to realize the low power fast settling multi-standard fractional-N frequency synthesizer. An auxiliary non-volatile memory （NVM） is embedded to avoid the repetitive calibration process and to save power in practical application. This PLL is implemented in a 0.18 #m technology. The frequency range is 0.3 to 2.54 GHz and the settling time is less than 5 #s over the entire frequency range. The LC-VCO with the stacked divide-by-2 has a good figure of merit of-193.5 dBc/Hz. The measured phase noise of frequency synthesizer is about -115 dBc/Hz at 1 MHz offset when the carrier frequency is 2.4 GHz and the reference spurs are less than -52 dBc. The whole frequency synthesizer consumes only 4.35 mA @ 1.8 V.展开更多
A triple-mode fractional-N frequency synthesizer with a noise-filter voltage controlled oscillator（VCO） for WCDMA/Bluetooth/ZigBee applications has been implemented in 0.18-μm RF-CMOS technology.The proposed synthe...A triple-mode fractional-N frequency synthesizer with a noise-filter voltage controlled oscillator（VCO） for WCDMA/Bluetooth/ZigBee applications has been implemented in 0.18-μm RF-CMOS technology.The proposed synthesizer achieves a good phase noise lower than-80 dBc/Hz in band and-115 dBc/Hz @ 1 MHz for the three modes, and only draws 21 mA from a 1.8 V supply.It has a high hardware sharing and a small size, only 1.5 × 1.4 mm2.The system architecture, circuit design, and measured results are also presented.展开更多
With the rapid evolution of wireless communication technology, integrating various communication modes in a mobile terminal has become the popular trend. Because of this, multi-standard wireless technology is one of t...With the rapid evolution of wireless communication technology, integrating various communication modes in a mobile terminal has become the popular trend. Because of this, multi-standard wireless technology is one of the hot spots in current research. This paper presents a wideband fractional-N frequency divider of the multi-standard wireless transceiver for many applications. High-speed divider-by-2 with traditional source- coupled-logic is designed for very wide band usage. Phase switching technique and a chain of divider-by-2/3 are applied to the programmable frequency divider with 0.5 step. The phase noise of the whole frequency synthesizer will be decreased by the narrower step of programmable frequency divider. A-E modulator is achieved by an improved MASH 1-1-1 structure. This structure has excellent performance in many ways, such as noise, spur and input dynamic range. Fabricated in TSMC 0.18/tin CMOS process, the fractional-N frequency divider occupies a chip area of 1130 × 510μm^2 and it can correctly divide within the frequency range of 0.8-9 GHz. With 1.8 V supply voltage, its division ratio ranges from 62.5 to 254 and the total current consumption is 29 mA.展开更多
A low-power, highly linear, multi-standard, active-RC filter with an accurate and novel tuning architecture is presented. It exhibits IEEE 802.11 a/b/g （9.5 MHz） and DVB-H （3 MHz, 4 MHz） application. The filter ex...A low-power, highly linear, multi-standard, active-RC filter with an accurate and novel tuning architecture is presented. It exhibits IEEE 802.11 a/b/g （9.5 MHz） and DVB-H （3 MHz, 4 MHz） application. The filter exploits digitally-controlled polysilicon resistor banks and a phase lock loop type automatic tuning system. The novel and complex automatic frequency calibration scheme provides better than 4 corner frequency accuracy, and it can be powered down after calibration to save power and avoid digital signal interference. The filter achieves OIP3 of 26 dBm and the measured group delay variation of the receiver filter is 50 ns （WLAN mode）. Its dissipation is 3.4 mA in RX mode and 2.3 mA （only for one path） in TX mode from a 2.85 V supply. The dissipation of calibration consumes 2 mA. The circuit has been fabricated in a 0.35μm 47 GHz SiGe BiCMOS technology; the receiver and transmitter filter occupy 0.21 mm^2 and 0.11 mm^2 （calibration circuit excluded）, respectively.展开更多
This paper proposes a sigma-delta fractional-N frequency synthesizer-based multi-standard I/Q carrier generation system.With reasonable frequency planning,the system can be used in multi-standard wireless communicatio...This paper proposes a sigma-delta fractional-N frequency synthesizer-based multi-standard I/Q carrier generation system.With reasonable frequency planning,the system can be used in multi-standard wireless communication applications（GSM,WCDMA,GPRS,TD-SCDMA,WLAN（802.11a/b/g））.The implementation is achieved by a 0.13μm RF CMOS process.The measured results demonstrate that three quadrature VCOs（QVCO） continuously cover the frequency from 3.1 to 6.1 GHz（65.2%）,and through the successive divide-by-2 prescalers to achieve the frequency from 0.75 to 6.1 GHz continuously.The chip was fully integrated with the exception of an off-chip filter.The entire chip area is only 3.78 mm^2,and the system consumes a 21.7 mA@1.2 V supply without output buffers.The lock-in time of the PLL frequency synthesizer is less than 4μs over the entire frequency range with a direct frequency presetting technique and the auxiliary non-volatile memory（NVM）can store the digital configuration signal of the system,including presetting signals to avoid the calibration process case by case.展开更多
A fully integrated hybrid integer/fractional frequency synthesizer is presented.With a single multiband voltage-controlled-oscillator（VCO）,the frequency synthesizer can support GPS,Galileo,Compass and TDSCDMA standa...A fully integrated hybrid integer/fractional frequency synthesizer is presented.With a single multiband voltage-controlled-oscillator（VCO）,the frequency synthesizer can support GPS,Galileo,Compass and TDSCDMA standards.Design is carefully performed to trade off power,die area and phase noise performance.By reconfiguring between the integer mode and fractional mode,different frequency resolution requirements and a constant loop bandwidth for each standard can be achieved simultaneously.Moreover,a long sequence length,reduced hardware complexity multi-stage-noise-shaping（MASH）.-.modulator is employed to reduce fractional spur in the fractional mode.Fabricated in a 0.18 m CMOS technology,the frequency synthesizer occupies an active area of 1.48 mm2 and draws a current of 13.4-16.2 mA from a 1.8 V power supply.The measured phase noise is lower than-80 dBc/Hz at 100 kHz offset and-113 to-124 dBc/Hz at 1 MHz offset respectively,while the measured reference spur is-71 dBc in integer mode and the fractional spur is-65 dBc in fractional mode.展开更多
This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load imp...This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load impedance on the linearity of a mixer is analyzed.Specially,the impact of the input impedance of the transimpedance amplifier（TIA）,which acts as the load impedance of a mixer,is investigated in detail.The analysis is verified by a passive mixer implemented with 0.18 μm CMOS technology.The circuit is inductorless and can operate over a broad frequency range.On wafer measurements show that,with radio frequency（RF） ranges from 700 MHz to 2.3 GHz,the mixer achieves 21 dB of conversion voltage gain with a-1 dB intermediate frequency（IF） bandwidth of 10 MHz.The measured IIP3 is 9 dBm and the measured double-sideband noise figure（NF） is 10.6 dB at 10 MHz output.The chip occupies an area of 0.19 mm2 and drains a current of 5.5 mA from a 1.8 V supply.展开更多
基金Supported by the National Basic Research Program of China(No.2010CB327404)the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘An adjustable mixer for surface acoustic wave( SAW)-less radio frequency( RF) front-end is presented in this paper. Through changing the bias voltage,the presented mixer with reconfigurable voltage conversion gain( VCG) is suitable for multi-mode multi-standard( MMMS) applications. An equivalent local oscillator( LO) frequency-tunable high-Q band-pass filter( BPF) at low noise amplifier( LNA) output is used to reject the out-of-band interference signals. Base-band( BB) capacitor of the mixer is variable to obtain 15 kinds of intermediate frequency( IF) bandwidth( BW). The proposed passive mixer with LNA is implemented in TSMC 0. 18μm RF CMOS process and operates from 0. 5 to 2. 5 GHz with measured maximum out-of-band rejection larger than 40 d B. The measured VCG of the front-end can be changed from 5 to 17 d B; the maximum input intercept point( IIP3) is0 d Bm and the minimum noise figure( NF) is 3. 7 d B. The chip occupies an area of 0. 44 mm^2 including pads.
文摘This paper describes a novel divide-by-32/33 dual-modulus prescaler （DMP）. Here, a new combination of DFF has been introduced in the DMP. By means of the cooperation and coordination among three types, DFF, SCL, TPSC, and CMOS static flip-flop, the DMP demonstrates high speed, wideband, and low power consumption with low phase noise. The chip has been fabricated in a 0.18μm CMOS process of SMIC. The measured results show that the DMP＇s operating frequency is from 0.9 to 3.4 GHz with a maximum power consumption of 2.51 mW under a 1.8 V power supply and the phase noise is -134.78 dBc/Hz at 1 MHz offset from the 3.4 GHz carrier. The core area of the die without PAD is 57 x 30 #m2. Due to its excellent performance, the DMP could be applied to a PLL-based frequency synthesizer for many RF systems, especially for multi-standard radio applications.
基金Project supported by the National Natural Science Foundation of China(No.60976023)the National Science and Technology Major Project of China(Nos.2009ZX03007-001,2012ZX03004007-002)
文摘A low power fast settling multi-standard CMOS fractional-N frequency synthesizer is proposed. The current reusing and frequency presetting techniques are adopted to realize the low power fast settling multi-standard fractional-N frequency synthesizer. An auxiliary non-volatile memory （NVM） is embedded to avoid the repetitive calibration process and to save power in practical application. This PLL is implemented in a 0.18 #m technology. The frequency range is 0.3 to 2.54 GHz and the settling time is less than 5 #s over the entire frequency range. The LC-VCO with the stacked divide-by-2 has a good figure of merit of-193.5 dBc/Hz. The measured phase noise of frequency synthesizer is about -115 dBc/Hz at 1 MHz offset when the carrier frequency is 2.4 GHz and the reference spurs are less than -52 dBc. The whole frequency synthesizer consumes only 4.35 mA @ 1.8 V.
基金supported by the Beijing Municipal Science & Technology Development Program(No.D0305003040111)the National Natural Science Foundation of China (No. 90407006)
文摘A triple-mode fractional-N frequency synthesizer with a noise-filter voltage controlled oscillator（VCO） for WCDMA/Bluetooth/ZigBee applications has been implemented in 0.18-μm RF-CMOS technology.The proposed synthesizer achieves a good phase noise lower than-80 dBc/Hz in band and-115 dBc/Hz @ 1 MHz for the three modes, and only draws 21 mA from a 1.8 V supply.It has a high hardware sharing and a small size, only 1.5 × 1.4 mm2.The system architecture, circuit design, and measured results are also presented.
文摘With the rapid evolution of wireless communication technology, integrating various communication modes in a mobile terminal has become the popular trend. Because of this, multi-standard wireless technology is one of the hot spots in current research. This paper presents a wideband fractional-N frequency divider of the multi-standard wireless transceiver for many applications. High-speed divider-by-2 with traditional source- coupled-logic is designed for very wide band usage. Phase switching technique and a chain of divider-by-2/3 are applied to the programmable frequency divider with 0.5 step. The phase noise of the whole frequency synthesizer will be decreased by the narrower step of programmable frequency divider. A-E modulator is achieved by an improved MASH 1-1-1 structure. This structure has excellent performance in many ways, such as noise, spur and input dynamic range. Fabricated in TSMC 0.18/tin CMOS process, the fractional-N frequency divider occupies a chip area of 1130 × 510μm^2 and it can correctly divide within the frequency range of 0.8-9 GHz. With 1.8 V supply voltage, its division ratio ranges from 62.5 to 254 and the total current consumption is 29 mA.
文摘A low-power, highly linear, multi-standard, active-RC filter with an accurate and novel tuning architecture is presented. It exhibits IEEE 802.11 a/b/g （9.5 MHz） and DVB-H （3 MHz, 4 MHz） application. The filter exploits digitally-controlled polysilicon resistor banks and a phase lock loop type automatic tuning system. The novel and complex automatic frequency calibration scheme provides better than 4 corner frequency accuracy, and it can be powered down after calibration to save power and avoid digital signal interference. The filter achieves OIP3 of 26 dBm and the measured group delay variation of the receiver filter is 50 ns （WLAN mode）. Its dissipation is 3.4 mA in RX mode and 2.3 mA （only for one path） in TX mode from a 2.85 V supply. The dissipation of calibration consumes 2 mA. The circuit has been fabricated in a 0.35μm 47 GHz SiGe BiCMOS technology; the receiver and transmitter filter occupy 0.21 mm^2 and 0.11 mm^2 （calibration circuit excluded）, respectively.
基金Project supported by the Chinese National High-Tech Research and Development Program(Nos2009ZX03007-001,2009AA011606)the National Natural Science Foundation of China(No60976023)
文摘This paper proposes a sigma-delta fractional-N frequency synthesizer-based multi-standard I/Q carrier generation system.With reasonable frequency planning,the system can be used in multi-standard wireless communication applications（GSM,WCDMA,GPRS,TD-SCDMA,WLAN（802.11a/b/g））.The implementation is achieved by a 0.13μm RF CMOS process.The measured results demonstrate that three quadrature VCOs（QVCO） continuously cover the frequency from 3.1 to 6.1 GHz（65.2%）,and through the successive divide-by-2 prescalers to achieve the frequency from 0.75 to 6.1 GHz continuously.The chip was fully integrated with the exception of an off-chip filter.The entire chip area is only 3.78 mm^2,and the system consumes a 21.7 mA@1.2 V supply without output buffers.The lock-in time of the PLL frequency synthesizer is less than 4μs over the entire frequency range with a direct frequency presetting technique and the auxiliary non-volatile memory（NVM）can store the digital configuration signal of the system,including presetting signals to avoid the calibration process case by case.
基金Project supported by the National Science and Technology Major Project,China (No.2010ZX03007-002-01)the State Key Development Program for Basic Research of China (No.2010CB327404)
文摘A fully integrated hybrid integer/fractional frequency synthesizer is presented.With a single multiband voltage-controlled-oscillator（VCO）,the frequency synthesizer can support GPS,Galileo,Compass and TDSCDMA standards.Design is carefully performed to trade off power,die area and phase noise performance.By reconfiguring between the integer mode and fractional mode,different frequency resolution requirements and a constant loop bandwidth for each standard can be achieved simultaneously.Moreover,a long sequence length,reduced hardware complexity multi-stage-noise-shaping（MASH）.-.modulator is employed to reduce fractional spur in the fractional mode.Fabricated in a 0.18 m CMOS technology,the frequency synthesizer occupies an active area of 1.48 mm2 and draws a current of 13.4-16.2 mA from a 1.8 V power supply.The measured phase noise is lower than-80 dBc/Hz at 100 kHz offset and-113 to-124 dBc/Hz at 1 MHz offset respectively,while the measured reference spur is-71 dBc in integer mode and the fractional spur is-65 dBc in fractional mode.
基金Project supported by the National Science and Technology Major Project (No.2010ZX03007-002-01)the State Key Development Program for Basic Research of China (No.2010CB327404)
文摘This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load impedance on the linearity of a mixer is analyzed.Specially,the impact of the input impedance of the transimpedance amplifier（TIA）,which acts as the load impedance of a mixer,is investigated in detail.The analysis is verified by a passive mixer implemented with 0.18 μm CMOS technology.The circuit is inductorless and can operate over a broad frequency range.On wafer measurements show that,with radio frequency（RF） ranges from 700 MHz to 2.3 GHz,the mixer achieves 21 dB of conversion voltage gain with a-1 dB intermediate frequency（IF） bandwidth of 10 MHz.The measured IIP3 is 9 dBm and the measured double-sideband noise figure（NF） is 10.6 dB at 10 MHz output.The chip occupies an area of 0.19 mm2 and drains a current of 5.5 mA from a 1.8 V supply.
