High nitrogen stainless steel(HNS) is a nickel free austenitic stainless steel that is used as a structural component in defence applications for manufacturing battle tanks as a replacement of the existing armour grad...High nitrogen stainless steel(HNS) is a nickel free austenitic stainless steel that is used as a structural component in defence applications for manufacturing battle tanks as a replacement of the existing armour grade steel owing to its low cost, excellent mechanical properties and better corrosion resistance.Conventional fusion welding causes problems like nitrogen desorption, solidification cracking in weld zone, liquation cracking in heat affected zone, nitrogen induced porosity and poor mechanical properties.The above problems can be overcome by proper selection and procedure of joining process. In the present work, an attempt has been made to correlate the microstructural changes with mechanical properties of fusion and solid state welds of high nitrogen steel. Shielded metal arc welding(SMAW), gas tungsten arc welding(GTAW), electron beam welding(EBW) and friction stir welding(FSW) processes were used in the present work. Optical microscopy, scanning electron microscopy and electron backscatter diffraction were used to characterize microstructural changes. Hardness, tensile and bend tests were performed to evaluate the mechanical properties of welds. The results of the present investigation established that fully austenitic dendritic structure was found in welds of SMAW. Reverted austenite pools in the martensite matrix in weld zone and unmixed zones near the fusion boundary were observed in GTA welds. Discontinuous ferrite network in austenite matrix was observed in electron beam welds.Fine recrystallized austenite grain structure was observed in the nugget zone of friction stir welds.Improved mechanical properties are obtained in friction stir welds when compared to fusion welds. This is attributed to the refined microstructure consisting of equiaxed and homogenous austenite grains.展开更多
This paper examined the impact of the number of thermal cycles and augmented strain on hot cracking in AZ31 and AZ61 magnesium alloy. Statistical analyses were performed. Following observation using a scanning electro...This paper examined the impact of the number of thermal cycles and augmented strain on hot cracking in AZ31 and AZ61 magnesium alloy. Statistical analyses were performed. Following observation using a scanning electron microscope （SEM）, an energy dispersive spectrometer （EDS） was used for component analysis. Results showed that Al content in magnesium alloy has an effect on hot cracking susceptibility. In addition, the nonequilibrium solidification process produced segregation in Al content, causing higher liquid Mg-alloy rich Al content at grain boundaries, and resulting into liquefied grain boundaries of partially melted zone （PMZ）. In summary, under multiple thermal cycles AZ61 produced serious liquation cracking. AZ61 has higher （6 wt%） Al content and produced much liquefied Mg17Al12 at grain boundaries under multiple thermal cycles. The liquefied Mg17Al12 were pulled apart and hot cracks formed at weld metal HAZ due to the augmented strain. Since AZ31 had half the Al content of AZ61, its hot-cracking susceptibility was lower than AZ61. In addition, AZ61 showed longer total crack length （TCL） in one thermal cycle compared to that in three thermal cycles. This phenomenon was possibly due to high-temperature gasification of Al during the welding process, which resulted in lower overall Al content. Consequently, shorter hot cracks exhibited in three thermal cycles. It was found the Al content of AZ31 and AZ61 can be used to assess the hot-cracking susceptibility.展开更多
This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels.The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 2...This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels.The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 25817 quality level B, pitting corrosion potential of the weld metal of not less than that of the AISI304 base metal and a ratio of delta-ferrite in austenite matrix of the weld metal of not lower than 3%.Such a ratio is a criterion widely accepted to protect the weld metal from solidification cracking. At the welding current of 75 A and by using pure argon as a shielding gas 0 to 8 vol.% and applying a welding speed in the range of 2-3.5 mm·s^(-1) was found to give a complete weld bead with an increased depthper-width ratio(promote weldability). For welding speed in the range of 3 and 3.5 mm·s^(-1)(promote corrosion resistance). Increasing the welding speed in such a range decreased the amount of delta-ferrite in the austenite matrix, and increased the pitting corrosion potential of the weld metal to be 302 mV_(SCE).This value was still lower than the pitting corrosion potential of the AISI 304 base metal. Mixing nitrogen in argon shielding gas increased the nitrogen content in the weld. The optimum condition was found when using a welding speed of 3 mm· s^(-1) and mixing 1 vol.% of nitrogen in the argon shielding gas(promote weldability and corrosion resistance). Pitted areas after potentiodynamic test were observed in the austenite in which its Cr content was relatively low.展开更多
TiC/TisSi3 composites were fabricated on Ti-5A1-2.5Sn substrates by gas tungsten arc welding （GTAW）. Identification of the phases was performed using X-ray diffraction （XRD）. The microstructures were analyzed usin...TiC/TisSi3 composites were fabricated on Ti-5A1-2.5Sn substrates by gas tungsten arc welding （GTAW）. Identification of the phases was performed using X-ray diffraction （XRD）. The microstructures were analyzed using scanning electron microscopy （SEM） combined with energy-dispersive X-ray spectrometry （EDS） and optical microscopy （OM）. The Vickers hardness was measured with a micro-hardness tester. The TiC/TisSi3 composites were obtained in a double-layer track, and the Vickers hardness of the track increased by two to three times compared with the Ti-5A1-2.5Sn substrate.展开更多
Presents penetration control by weld pool resonance which occurs when the natural frequency of weld pool is equal to the frequency of sine wave current while the weld pool is excited into oscillation by superimposing ...Presents penetration control by weld pool resonance which occurs when the natural frequency of weld pool is equal to the frequency of sine wave current while the weld pool is excited into oscillation by superimposing sine wave current with definite frequency or regular frequency on DC current, and experiments carried out on detecting resonance signals during both stationary and travelling arc welding with variant frequency pulse current, and concludes with experimental results that penetration control can be realized by weld pool resonance when welding speed is lower than 80mm/min, and this control method is applicable to welding thin (0.5～3.0 mm) plates of carbon steel, low alloy steel, high strength steel and superhigh strength steel, and suitable for alternating polarity welding of stainless steel, titanium alloy steel and aluminum alloy.展开更多
文摘High nitrogen stainless steel(HNS) is a nickel free austenitic stainless steel that is used as a structural component in defence applications for manufacturing battle tanks as a replacement of the existing armour grade steel owing to its low cost, excellent mechanical properties and better corrosion resistance.Conventional fusion welding causes problems like nitrogen desorption, solidification cracking in weld zone, liquation cracking in heat affected zone, nitrogen induced porosity and poor mechanical properties.The above problems can be overcome by proper selection and procedure of joining process. In the present work, an attempt has been made to correlate the microstructural changes with mechanical properties of fusion and solid state welds of high nitrogen steel. Shielded metal arc welding(SMAW), gas tungsten arc welding(GTAW), electron beam welding(EBW) and friction stir welding(FSW) processes were used in the present work. Optical microscopy, scanning electron microscopy and electron backscatter diffraction were used to characterize microstructural changes. Hardness, tensile and bend tests were performed to evaluate the mechanical properties of welds. The results of the present investigation established that fully austenitic dendritic structure was found in welds of SMAW. Reverted austenite pools in the martensite matrix in weld zone and unmixed zones near the fusion boundary were observed in GTA welds. Discontinuous ferrite network in austenite matrix was observed in electron beam welds.Fine recrystallized austenite grain structure was observed in the nugget zone of friction stir welds.Improved mechanical properties are obtained in friction stir welds when compared to fusion welds. This is attributed to the refined microstructure consisting of equiaxed and homogenous austenite grains.
文摘This paper examined the impact of the number of thermal cycles and augmented strain on hot cracking in AZ31 and AZ61 magnesium alloy. Statistical analyses were performed. Following observation using a scanning electron microscope （SEM）, an energy dispersive spectrometer （EDS） was used for component analysis. Results showed that Al content in magnesium alloy has an effect on hot cracking susceptibility. In addition, the nonequilibrium solidification process produced segregation in Al content, causing higher liquid Mg-alloy rich Al content at grain boundaries, and resulting into liquefied grain boundaries of partially melted zone （PMZ）. In summary, under multiple thermal cycles AZ61 produced serious liquation cracking. AZ61 has higher （6 wt%） Al content and produced much liquefied Mg17Al12 at grain boundaries under multiple thermal cycles. The liquefied Mg17Al12 were pulled apart and hot cracks formed at weld metal HAZ due to the augmented strain. Since AZ31 had half the Al content of AZ61, its hot-cracking susceptibility was lower than AZ61. In addition, AZ61 showed longer total crack length （TCL） in one thermal cycle compared to that in three thermal cycles. This phenomenon was possibly due to high-temperature gasification of Al during the welding process, which resulted in lower overall Al content. Consequently, shorter hot cracks exhibited in three thermal cycles. It was found the Al content of AZ31 and AZ61 can be used to assess the hot-cracking susceptibility.
基金the Thai Government scholarship given via Rajamangala University of Technology Krungthep (UTK), Bangkok, Thailand, for their financial support through this funded research project
文摘This present study applied gas tungsten arc welding in order to join AISI 304 and AISI 201 stainless steels.The objective was to find the optimum welding condition that gave a weld bead in accordance with DIN EN ISO 25817 quality level B, pitting corrosion potential of the weld metal of not less than that of the AISI304 base metal and a ratio of delta-ferrite in austenite matrix of the weld metal of not lower than 3%.Such a ratio is a criterion widely accepted to protect the weld metal from solidification cracking. At the welding current of 75 A and by using pure argon as a shielding gas 0 to 8 vol.% and applying a welding speed in the range of 2-3.5 mm·s^(-1) was found to give a complete weld bead with an increased depthper-width ratio(promote weldability). For welding speed in the range of 3 and 3.5 mm·s^(-1)(promote corrosion resistance). Increasing the welding speed in such a range decreased the amount of delta-ferrite in the austenite matrix, and increased the pitting corrosion potential of the weld metal to be 302 mV_(SCE).This value was still lower than the pitting corrosion potential of the AISI 304 base metal. Mixing nitrogen in argon shielding gas increased the nitrogen content in the weld. The optimum condition was found when using a welding speed of 3 mm· s^(-1) and mixing 1 vol.% of nitrogen in the argon shielding gas(promote weldability and corrosion resistance). Pitted areas after potentiodynamic test were observed in the austenite in which its Cr content was relatively low.
基金financially supported by the Foundation of Education Department of Guangdong Province,China (No. 2010A090200034)
文摘TiC/TisSi3 composites were fabricated on Ti-5A1-2.5Sn substrates by gas tungsten arc welding （GTAW）. Identification of the phases was performed using X-ray diffraction （XRD）. The microstructures were analyzed using scanning electron microscopy （SEM） combined with energy-dispersive X-ray spectrometry （EDS） and optical microscopy （OM）. The Vickers hardness was measured with a micro-hardness tester. The TiC/TisSi3 composites were obtained in a double-layer track, and the Vickers hardness of the track increased by two to three times compared with the Ti-5A1-2.5Sn substrate.
文摘Presents penetration control by weld pool resonance which occurs when the natural frequency of weld pool is equal to the frequency of sine wave current while the weld pool is excited into oscillation by superimposing sine wave current with definite frequency or regular frequency on DC current, and experiments carried out on detecting resonance signals during both stationary and travelling arc welding with variant frequency pulse current, and concludes with experimental results that penetration control can be realized by weld pool resonance when welding speed is lower than 80mm/min, and this control method is applicable to welding thin (0.5～3.0 mm) plates of carbon steel, low alloy steel, high strength steel and superhigh strength steel, and suitable for alternating polarity welding of stainless steel, titanium alloy steel and aluminum alloy.
