A new analytical chip formation model is proposed for micro-end-milling operations. The model calculates an instantaneous uncut chip thickness by considering the combination of exact trochoidal trajectory of the tool ...A new analytical chip formation model is proposed for micro-end-milling operations. The model calculates an instantaneous uncut chip thickness by considering the combination of exact trochoidal trajectory of the tool tip and tool run-out, while the simplified circular trajectory and the neglected run-out create negligible change in conventional-scale chip formation models. Newton-Raphson iterative method is employed during the calculation to obtain quadratic convergence. The proposed approach allows the calculation of instantaneous uncut chip thickness to be done accurately and rapidly, and the prediction accuracy of this model is also verified by comparing the simulation results to experimental cutting forces.展开更多
Magnesium and magnesium in-situ composites have significant potential in the application of design and manufacturing for automotive and aerospace industries because of their high specific strength and reduced fuel con...Magnesium and magnesium in-situ composites have significant potential in the application of design and manufacturing for automotive and aerospace industries because of their high specific strength and reduced fuel consumption.But there are many challenges for machining of Mg based alloys and composites because of the high tendency of fire and oxidation.These challenges can be minimized through microstructural engineering.In this present study,the machining performances of AZ91 Mg alloy and in-situ hybrid TiC+TiB_(2)reinforced AZ91 metal matrix composite was investigated.The effectβ-Mg_(17)Al_(12)phases and grain refinement with and without in-situ particles on machinability were studied through microstructural engineering via aging and friction stir processing.The end milling operation was carried out at different cutting speeds ranging from 25 mm/min to 90 mm/min under dry environment by using an AlTiN-coated tungsten carbide tool.The optimum cutting speed for machining was found to be 75 mm/min based on the surface roughness values of all conditioned materials.The base material with dendritic microstructure was found to have poor machinability in terms of inadequate surface finish and edge-burrs formation.The combined effect of in-situ TiC+TiB_(2)particles addition and grain refinement enhanced the machining performance of the material with superior surface finish,negligible edge-burr formation and better tool wear resistance.The influence of in-situ TiC+TiB_(2)particles,β-Mg_(17)Al_(12)phases and grain refinement on machining characteristics are explained based on the tool wear mechanisms,chip behavior and machining induced affected zone.展开更多
Abstract Predictive models for machining operations have been significantly improved through numerous methods in recent decades. This study proposed a 3D finite element modeling （3D FEM） approach for the micro end-m...Abstract Predictive models for machining operations have been significantly improved through numerous methods in recent decades. This study proposed a 3D finite element modeling （3D FEM） approach for the micro end-milling orAl6061-T6. Finite element （FE） simulations were performed under different cutting conditions to obtain realistic numerical predictions of chip flow, burr formation, and cutting forces. FE modeling displayed notable advantages, such as capability to easily handle any type of tool geometry and any side effect on chip formation, including thermal aspect and material property changes. The proposed 3D FE model considers the effects ofmiU helix angle and cutting edge radius on the chip. The prediction capability of the FE model was validated by comparing numerical model and experimental test results. Burr dimension trends were correlated with force profile shapes. However, the FE predictions overestimated the real force magnitude. This overestimation indicates that the model requires further development.展开更多
Milling Process Simulation is one of the important re search areas in manufacturing science. For the purpose of improving the prec ision of simulation and extending its usability, numerical algorithm is more and more ...Milling Process Simulation is one of the important re search areas in manufacturing science. For the purpose of improving the prec ision of simulation and extending its usability, numerical algorithm is more and more used in the milling modeling areas. But simulative efficiency is decreasin g with increase of its complexity. As a result, application of the method is lim ited. Aimed at above question, high-efficient algorithm for milling process sim ulation is studied. It is important for milling process simulation’s applicatio n. Parallel computing is widely used to solve the large-scale computation question s. Its advantages include system flexibility, robust, high-efficient computing capability and high ratio of performance to price. With the development of compu ter network, utilizing the computing resource in the Internet, a virtual computi ng environment with powerful computing capability can be consisted by microc omputers, and the difficulty of building hardware environment which is used to s upport parallel computing is reduced. How to use network technology and parallel algorithm to improve simulative effic iency for milling forces simulation is investigated in the paper. In order to pr edict milling forces, a simplified local milling forces model is used in the pap er. End milling cutter is assumed to be divided by r number of differential elem ents along the axial direction of the cutter. For a given time, the total cuttin g forces can be obtained by summarizing the resultant cutting force produced by each differential cutter disc. Divide the whole simulative time into some segmen ts, send these program’s segments to microcomputers in the Internet and obtain the result of the program’s segments, all of the result of program’s segments a re composed the final result. For implementing the algorithm, a distributed Parallel computing framework is de signed in the paper. In the framework, web server plays a role of controller. Us ing Java RMI(remote method interface), the computing processes in comp展开更多
Many difficult-to-cut materials such as Ni-base super alloy, titanium alloy, and austenite stainless steel which are used extensively in aerospace generally have high strength-to-weight ratios, high corrosion resistan...Many difficult-to-cut materials such as Ni-base super alloy, titanium alloy, and austenite stainless steel which are used extensively in aerospace generally have high strength-to-weight ratios, high corrosion resistance, high strength retention ability at elevated temperatures, and low thermal conductivity. These characteristics can result in uneven tool wear and chatter vibration. Therefore, determining the appropriate end-milling conditions is more difficult for difficult-to-cut materials than for other materials. There has been much research on the high-speed milling of difficult-to-cut materials, and effective end-milling conditions, end-mill tool shapes, and processing methods have been reported. In addition, irregular pitch and lead end-mills with different helix angles have been developed by tool maker＇s to reduce chatter vibration, making it easier to perform high-speed milling. However, there have been few reports of slotting information useful for determining appropriate end-milling conditions and processing methods for Ni-base super alloy. The aim of this study is to derive end-milling condition with high efficiency grooving process for Ni-base super alloy （Inconel 718） sheet. Effects of cutting parameters were examined from the view point of cutting resistance, ＂tool tip maximum temperature and tool flank wear width. As a result from experiments, if the grooving process condition of axial depth of cut is smaller than other conditions on the same material removable rate value, it has been found that it is possible to reduce the tool tip maximum temperature and prolong the tool life.展开更多
基金supported by National Natural Science Foundation of China (No.50575134)
文摘A new analytical chip formation model is proposed for micro-end-milling operations. The model calculates an instantaneous uncut chip thickness by considering the combination of exact trochoidal trajectory of the tool tip and tool run-out, while the simplified circular trajectory and the neglected run-out create negligible change in conventional-scale chip formation models. Newton-Raphson iterative method is employed during the calculation to obtain quadratic convergence. The proposed approach allows the calculation of instantaneous uncut chip thickness to be done accurately and rapidly, and the prediction accuracy of this model is also verified by comparing the simulation results to experimental cutting forces.
基金the Ministry of Human Resource and Development for funding this Co E through Grant No.-SB20210992MEMHRD008517the support of the FIST grant,Department of Science and Technology,India(Grant#SR/FST/ET11059/2012(G))for the use of the electron microscopy facility
文摘Magnesium and magnesium in-situ composites have significant potential in the application of design and manufacturing for automotive and aerospace industries because of their high specific strength and reduced fuel consumption.But there are many challenges for machining of Mg based alloys and composites because of the high tendency of fire and oxidation.These challenges can be minimized through microstructural engineering.In this present study,the machining performances of AZ91 Mg alloy and in-situ hybrid TiC+TiB_(2)reinforced AZ91 metal matrix composite was investigated.The effectβ-Mg_(17)Al_(12)phases and grain refinement with and without in-situ particles on machinability were studied through microstructural engineering via aging and friction stir processing.The end milling operation was carried out at different cutting speeds ranging from 25 mm/min to 90 mm/min under dry environment by using an AlTiN-coated tungsten carbide tool.The optimum cutting speed for machining was found to be 75 mm/min based on the surface roughness values of all conditioned materials.The base material with dendritic microstructure was found to have poor machinability in terms of inadequate surface finish and edge-burrs formation.The combined effect of in-situ TiC+TiB_(2)particles addition and grain refinement enhanced the machining performance of the material with superior surface finish,negligible edge-burr formation and better tool wear resistance.The influence of in-situ TiC+TiB_(2)particles,β-Mg_(17)Al_(12)phases and grain refinement on machining characteristics are explained based on the tool wear mechanisms,chip behavior and machining induced affected zone.
文摘Abstract Predictive models for machining operations have been significantly improved through numerous methods in recent decades. This study proposed a 3D finite element modeling （3D FEM） approach for the micro end-milling orAl6061-T6. Finite element （FE） simulations were performed under different cutting conditions to obtain realistic numerical predictions of chip flow, burr formation, and cutting forces. FE modeling displayed notable advantages, such as capability to easily handle any type of tool geometry and any side effect on chip formation, including thermal aspect and material property changes. The proposed 3D FE model considers the effects ofmiU helix angle and cutting edge radius on the chip. The prediction capability of the FE model was validated by comparing numerical model and experimental test results. Burr dimension trends were correlated with force profile shapes. However, the FE predictions overestimated the real force magnitude. This overestimation indicates that the model requires further development.
文摘Milling Process Simulation is one of the important re search areas in manufacturing science. For the purpose of improving the prec ision of simulation and extending its usability, numerical algorithm is more and more used in the milling modeling areas. But simulative efficiency is decreasin g with increase of its complexity. As a result, application of the method is lim ited. Aimed at above question, high-efficient algorithm for milling process sim ulation is studied. It is important for milling process simulation’s applicatio n. Parallel computing is widely used to solve the large-scale computation question s. Its advantages include system flexibility, robust, high-efficient computing capability and high ratio of performance to price. With the development of compu ter network, utilizing the computing resource in the Internet, a virtual computi ng environment with powerful computing capability can be consisted by microc omputers, and the difficulty of building hardware environment which is used to s upport parallel computing is reduced. How to use network technology and parallel algorithm to improve simulative effic iency for milling forces simulation is investigated in the paper. In order to pr edict milling forces, a simplified local milling forces model is used in the pap er. End milling cutter is assumed to be divided by r number of differential elem ents along the axial direction of the cutter. For a given time, the total cuttin g forces can be obtained by summarizing the resultant cutting force produced by each differential cutter disc. Divide the whole simulative time into some segmen ts, send these program’s segments to microcomputers in the Internet and obtain the result of the program’s segments, all of the result of program’s segments a re composed the final result. For implementing the algorithm, a distributed Parallel computing framework is de signed in the paper. In the framework, web server plays a role of controller. Us ing Java RMI(remote method interface), the computing processes in comp
文摘Many difficult-to-cut materials such as Ni-base super alloy, titanium alloy, and austenite stainless steel which are used extensively in aerospace generally have high strength-to-weight ratios, high corrosion resistance, high strength retention ability at elevated temperatures, and low thermal conductivity. These characteristics can result in uneven tool wear and chatter vibration. Therefore, determining the appropriate end-milling conditions is more difficult for difficult-to-cut materials than for other materials. There has been much research on the high-speed milling of difficult-to-cut materials, and effective end-milling conditions, end-mill tool shapes, and processing methods have been reported. In addition, irregular pitch and lead end-mills with different helix angles have been developed by tool maker＇s to reduce chatter vibration, making it easier to perform high-speed milling. However, there have been few reports of slotting information useful for determining appropriate end-milling conditions and processing methods for Ni-base super alloy. The aim of this study is to derive end-milling condition with high efficiency grooving process for Ni-base super alloy （Inconel 718） sheet. Effects of cutting parameters were examined from the view point of cutting resistance, ＂tool tip maximum temperature and tool flank wear width. As a result from experiments, if the grooving process condition of axial depth of cut is smaller than other conditions on the same material removable rate value, it has been found that it is possible to reduce the tool tip maximum temperature and prolong the tool life.
