The homogeneity of low alloy steels continuous casting billet obtained under different technological conditions has been investigated by original position statistic distribution analysis technique. On the basis of sys...The homogeneity of low alloy steels continuous casting billet obtained under different technological conditions has been investigated by original position statistic distribution analysis technique. On the basis of systematic analysis of ten thousands primary optical signals at the corresponding original positions, the quantitative statistic distribution information of each element was obtained. The biggest degrees of segregation of low alloy steel continuous casting billet were calculated accurately according to the quantitative distribution maps of the contents. It was suggested that the weight ratio in a certain content range was used to judge the homogeneity of the materials, and the two models —— the total weight ratio of contents (the degree of statistic homogeneity, H) within the permissive content range (C0±R) and the median value confidence extension ratio (the degree of statistic segregation, S) at 95% of confidence limit of weight ratio —— were put forward. The two models reflect the composition and state distribution regularity of the metal materials in a large region. The difference between the sample with high columnar crystal and the sample with high equiaxed crystal has been studied by using the two models.展开更多
The West Junggar of the western Central Asian Orogenic Belt is one of the typical regions in the term of ocean subduction, contraction and continental growth in the Late Paleozoic. However, it is still controversial o...The West Junggar of the western Central Asian Orogenic Belt is one of the typical regions in the term of ocean subduction, contraction and continental growth in the Late Paleozoic. However, it is still controversial on the exact time of ocean-continent transition so far. This study investigates rhyolites with columnar joint in the West Junggar for the first time.Based on zircon U-Pb dating, we determined that the ages of the newly-discovered rhyolites are between 303.6 and 294.5 Ma, belonging to Late Carboniferous–Early Permian, which is the oldest rhyolite with columnar joint preserved in the world at present. Geochemical results show that the characteristics of the major element compositions include a high content of SiO_2(75.78–79.20 wt%) and a moderate content of Al_2O_3(12.21–13.19 wt%). The total alkali content(K_2O +Na_2O) is 6.14–8.05 wt%, among which K_2O is 2.09–4.72 wt% and the rate of K_2O/Na_2O is 0.38–3.05. Over-based minerals such as Ne, Lc, and Ac do not appear. The contents of TiO_2(0.09–0.24 wt%), CaO(0.15–0.99 wt%) and MgO(0.06–0.18 wt%) are low. A/CNK=0.91–1.68, A/NK=1.06–1.76, and as such, these are associated with the quasi-aluminum-weak peraluminous high potassium calc-alkaline and some calc-alkaline magma series. These rhyolites show a significant negative Eu anomaly with relative enrichment of LREE and LILE(Rb, Ba, Th, U, K) and depletion of Sr, HREE and HFSE(Nb, Ta, Ti, P). These rhyolites also have the characteristics of an A2-type granite, similar to the Miaoergou batholith,which indicates they both were affected by post-orogenic extension. Combining petrological, zircon U-Pb dating and geochemical characteristics of the rhyolites, we conclude that the specific time of ocean-continent transition of the West Junggar is the Late Carboniferous–Early Permian.展开更多
A new approach to applying the electric current pulse （ECP） with parallel electrodes to the promotion of the transition from columnar crystal to equiaxed crystal and the improvement of macrosegregation was introduce...A new approach to applying the electric current pulse （ECP） with parallel electrodes to the promotion of the transition from columnar crystal to equiaxed crystal and the improvement of macrosegregation was introduced. The ECP was applied to different stages of the solidification. The results showed that the application of the ECP in both the initial stage （the thickness of solidified shell reached 2 mm approximately） and the late stage （the thickness of solidified shell reached 14 mm approximately） of solidification can promote the columnar to equiaxed transition （CET）. The analysis showed that during solidification, a large number of nuclei around the upper surface fell off due to ECP, which subsequently showered on the melt and impinged the growth front of the columnar crystal. Therefore, the CEToccurred. In addition, this method was also employed to influence the solidification process of bearing steel, and the results showed that the structure was changed from columnar crystal to equiaxed crystal, indicating that ECP can enhance the homogeneity of structure and composition of bearing steel.展开更多
From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the A...From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the AUTOCAD model into 3DEC (3-dimensional distinct element code) model was developed, and a numerical model was established in 3DEC. Moreover, the results of triaxial compression tests of columnar jointed rock masses were simulated numerically. The REV (representative element volume) scale was studied, and the result shows that the REV size is 3 m × 3 m. The proposed approach, the established model and the numerical simulation were applied to study the macro-mechanical properties and the equivalent strength parameters of the columnar jointed rock mass. The numerical simulation results are in good accordance with the in-situ test results.展开更多
A series of new trialkoxytrialkanoyloxytriphenylene TP（OCnH2n＋1）3（OCOCmH2m＋1）3 （5a-5e） （n =m＋1 =4- 8） discotic liquid crystals were prepared and their mesomorphic properties were investigated using differen...A series of new trialkoxytrialkanoyloxytriphenylene TP（OCnH2n＋1）3（OCOCmH2m＋1）3 （5a-5e） （n =m＋1 =4- 8） discotic liquid crystals were prepared and their mesomorphic properties were investigated using differential scanning calorimetry （DSC） and polarizing optical microscopy （POM）. The symmetrical and shorter chain triphenylenes display higher melting points and clearing points, more highly ordered and stable columnar mesophase than the asymmetrical and longer chain triphenylenes respectively.展开更多
Small change in chemical structure of discotic liquid crystals can cause big difference in their mesomorphism. Replacing of the alkoxy peripheral chains of triphenylene by oxygen-atom containing ester chains would res...Small change in chemical structure of discotic liquid crystals can cause big difference in their mesomorphism. Replacing of the alkoxy peripheral chains of triphenylene by oxygen-atom containing ester chains would result in novel mesomorphism. A series of mixed tail triphenylenes containing propoxyacetyloxy and alkoxy, abbreviated as C18H6（OCnH2n＋1）3（OCOCH2OC3H7）3, n=4-8, and hexa（propyloxyacetyloxy）triphenylene, C18H6（OCOCH2OC3H7）6 were synthesized. Thermal gravimetry analysis （TGA） of three discogens showed that they had good thermal stability till 350 ℃. The mesomorphism was investigated through differential scanning calorimetry （DSC） and polarized optical microscopy （POM）. The preliminary X-ray diffraction （XRD） results of one compound showed that it exhibited ordered hexagonal columnar （Colho） mesophase. These mixed tail triphenylene derivatives possessed much stable Colho mesophase and wider mesophase ranges than their hexaalkoxytriphenylene C18H6（OR）6 and hexaalkanoyloxytriphenylene C18H6（OCOR＇）6 analogues. The asymmetrical compounds 2,6,11-trialkoxy-3,7,10-tri（2-propyloxyacetyloxy）triphenylenes with n=5-8 displayed higher clearing points and wider temperature ranges than their symmetrical isomers 2,6,10-trialkoxy-3,7,11-tri（2-propyloxyacetyloxy）- triphenylenes, while C18H6（OCOCH2OC3H7）6 had the highest clearing point due to the β-oxygen-atom effect.展开更多
The microstructure and mechanical properties of Cu-12wt%Al alloy wires which are composed of continuous columnar crystals after dieless drawing forming at drawing speed of 1.0–1.4 mm/s and deformation temperature of ...The microstructure and mechanical properties of Cu-12wt%Al alloy wires which are composed of continuous columnar crystals after dieless drawing forming at drawing speed of 1.0–1.4 mm/s and deformation temperature of 600–900°C were analyzed, and deformation behavior of the alloy during dieless drawing forming was experimentally investigated. The results showed that in the above-mentioned conditions, recrystallization phenomenon was not found during dieless drawing forming. When a drawing speed of 1.0 mm/s was used, the grain boundaries were out of straight gradually with increasing deformation temperature from 600°C to 900°C, and tensile strength of the dieless drawn Cu-12wt%Al alloy wires increased while elongations decreased with increasing deformation temperature. At drawing speed of 1.1–1.2 mm/s and deformation temperature of 600°C, the effect of dieless drawing forming process on the microstructure of the alloy was inconspicuous, and when drawing speed was up to 1.3–1.4 mm/s, the grain boundaries of continuous columnar crystals became zigzag while there was little effect of drawing speed of 1.1–1.4 mm/s on the elongation and tensile strength of the alloy wires.展开更多
Connecting two discotic mesogens via a spacer not only stabilizes the columnar mesophase but also leads to the formation of glass columnar phase, and therefore improves the physical properties of discotic liquid cryst...Connecting two discotic mesogens via a spacer not only stabilizes the columnar mesophase but also leads to the formation of glass columnar phase, and therefore improves the physical properties of discotic liquid crystals as organic semiconductor. Here, we report the synthesis of eight diacetylene-bridged triphenylene discotic liquid crystal dimers, [C18H6(OC n H2n+1)4(OMe)O2C?C8H16?C≡C?]2, 3(n), (n = 4–8), [C18H6(OC6H13)5O2C?C8H16?C≡C?]2, 6 and [C18H6(OC6H13)5O?(CH2)m?C≡C?]2, 8(m), (m = 1, 3) by Eglinton coupling reaction. The thermotropic liquid crystal properties were studied by differential scanning calorimetry and polarized optical microscopy. The results are showed as follows: the length of peripheral alkyl chains of triphenylene influenced properties of liquid crystal dimers; dimers 3(n) (n = 5–8) and 6 had glass columnar phase, and no crystallization was observed above ?50°C for all the triphenylene dimers; compared with 3(6), 6 showed higher molecular symmetry, more stable columnar mesophase and wider mesophase range. The connecting group, length and rigidity of spacer had important influence on the mesomorphism of diacetylene-bridged triphenylene discotic liquid crystal dimers.展开更多
Considering the S L interface morphology stability, the S L interface energy, the Joule heat produced by electric current at the S L interface, and the change of solute concentration at the S L interface indirectly ca...Considering the S L interface morphology stability, the S L interface energy, the Joule heat produced by electric current at the S L interface, and the change of solute concentration at the S L interface indirectly caused by electric current, the mechanism of reduction of columnar dendrite spacing in unidirectional solidification caused by electric current passing through solid liquid interface was studied. The following conclusions can be drawn that: 1) under sub rapid solidification condition, increasing electric current density will improve the stability of S L interface, thus decreasing the columnar dendrite spacing; 2)there are two ways by which the increase of electric current decreases the columnar dendrite spacing, one is promoting the splitting of the protruding tips at the S L interface, the other is promoting the forming of new convex parts at the bottom of the concave interface.[展开更多
BACKGROUND Recently,research has linked Helicobacter pylori(H.pylori)stomach infection to colonic inflammation,mediated by toxin production,potentially impacting colorectal cancer occurrence.AIM To investigate the ris...BACKGROUND Recently,research has linked Helicobacter pylori(H.pylori)stomach infection to colonic inflammation,mediated by toxin production,potentially impacting colorectal cancer occurrence.AIM To investigate the risk factors for post-colon polyp surgery,H.pylori infection,and its correlation with pathologic type.METHODS Eighty patients who underwent colon polypectomy in our hospital between January 2019 and January 2023 were retrospectively chosen.They were then randomly split into modeling(n=56)and model validation(n=24)sets using R.The modeling cohort was divided into an H.pylori-infected group(n=37)and an H.pylori-uninfected group(n=19).Binary logistic regression analysis was used to analyze the factors influencing the occurrence of H.pylori infection after colon polyp surgery.A roadmap prediction model was established and validated.Finally,the correlation between the different pathological types of colon polyps and the occurrence of H.pylori infection was analyzed after colon polyp surgery.RESULTS Univariate results showed that age,body mass index(BMI),literacy,alcohol consumption,polyp pathology type,high-risk adenomas,and heavy diet were all influential factors in the development of H.pylori infection after intestinal polypectomy.Binary multifactorial logistic regression analysis showed that age,BMI,and type of polyp pathology were independent predictors of the occurrence of H.pylori infection after intestinal polypectomy.The area under the receiver operating characteristic curve was 0.969[95%confidence interval(95%CI):0.928–1.000]and 0.898(95%CI:0.773–1.000)in the modeling and validation sets,respectively.The slope of the calibration curve of the graph was close to 1,and the goodness-of-fit test was P>0.05 in the two sets.The decision analysis curve showed a high rate of return in both sets.The results of the correlation analysis between different pathological types and the occurrence of H.pylori infection after colon polyp surgery showed that hyperplastic polyps,inflammatory polyps,and the occurrenc展开更多
BACKGROUND Neutrophil-lymphocyte ratio(NLR),fibrosis index based on four factors(Fib4),aspartate aminotransferase-to-platelet ratio index(APRI)can be used for prognostic evaluation of hepatocellular carcinoma.However,...BACKGROUND Neutrophil-lymphocyte ratio(NLR),fibrosis index based on four factors(Fib4),aspartate aminotransferase-to-platelet ratio index(APRI)can be used for prognostic evaluation of hepatocellular carcinoma.However,no study has established an individualized prediction model for the prognosis of hepatocellular carcinoma based on these factors.AIM To screen the factors that affect the prognosis of hepatocellular carcinoma and establish a nomogram model that predicts postoperative liver failure after hepatic resection in patients with hepatocellular carcinoma.METHODS In total,220 patients with hepatocellular carcinoma treated in our hospital from January 2022 to January 2023 were selected.They were divided into 154 participants in the modeling cohort,and 66 in the validation cohort.Comparative analysis of the changes in NLR,Fib4,and APRI levels in 154 patients with hepatocellular carcinoma before liver resection and at 3 mo,6 mo,and 12 mo postoperatively was conducted.Binary logistic regression to analyze the influencing factors on the occurrence of liver failure in hepatocellular carcinoma patients,roadmap prediction modeling,and validation,patient work characteristic curves(ROCs)to evaluate the predictive efficacy of the model,calibration curves to assess the consistency,and decision curve analysis(DCA)to evaluate the model’s validity were also conducted.RESULTS Binary logistic regression showed that Child-Pugh grading,Surgical site,NLR,Fib4,and APRI were all risk factors for liver failure after hepatic resection in patients with hepatocellular carcinoma.The modeling cohort built a column-line graph model,and the area under the ROC curve was 0.986[95%confidence in terval(CI):0.963-1.000].The patients in the validation cohort utilized the column-line graph to predict the probability of survival in the validation cohort and plotted the ROC curve with an area under the curve of the model of 0.692(95%CI:0.548-0.837).The deviation of the actual outcome curves from the calibration curves of the column-line plots gen展开更多
Columnar nanocrystalline aluminum nitride(cnc-AlN) thin films with(002) orientation and uniform texture have been deposited successfully on large silicon wafers by RF reactive magnetron sputtering.At the optimum sputt...Columnar nanocrystalline aluminum nitride(cnc-AlN) thin films with(002) orientation and uniform texture have been deposited successfully on large silicon wafers by RF reactive magnetron sputtering.At the optimum sputtering parameters, the deposited cnc-AlN thin films show a c-axis preferred orientation with a crystallite size of about 28 nm and surface roughness(RMS) of about 1.29 nm. The cnc-AlN thin films were well transparent with an optical band gap about 4.8 e V, and the residual compressive stress and the defect density in the film have been revealed by Ramon spectroscopy. Moreover, piezoelectric performances of the cnc-AlN thin films executed effectively in a film bulk acoustic resonator structure.展开更多
Isothermal hot compression tests of as-cast high-Cr ultra-super-critical（USC） rotor steel with columnar grains perpendicular to the compression direction were carried out in the temperature range from 950 to 1250...Isothermal hot compression tests of as-cast high-Cr ultra-super-critical（USC） rotor steel with columnar grains perpendicular to the compression direction were carried out in the temperature range from 950 to 1250°C at strain rates ranging from 0.001 to 1 s^（-1）. The softening mechanism was dynamic recovery（DRV） at 950°C and the strain rate of 1 s^（-1）, whereas it was dynamic recrystallization（DRX） under the other conditions. A modified constitutive equation based on the Arrhenius model with strain compensation reasonably predicted the flow stress under various deformation conditions, and the activation energy was calculated to be 643.92 kJ ×mol^（-1）. The critical stresses of dynamic recrystallization under different conditions were determined from the work-hardening rate（θ）–flow stress（σ） and-θ/σ–σ curves. The optimum processing parameters via analysis of the processing map and the softening mechanism were determined to be a deformation temperature range from 1100 to 1200°C and a strain-rate range from 0.001 to 0.08 s^（-1）, with a power dissipation efficiency η greater than 31%.展开更多
The ocean,with its highly variable and complex meteorological conditions,harbors enormous renewable resources.Triboelectric nanogenerators(TENGs),which possess unique advantages,show exciting prospects in water wave e...The ocean,with its highly variable and complex meteorological conditions,harbors enormous renewable resources.Triboelectric nanogenerators(TENGs),which possess unique advantages,show exciting prospects in water wave energy collection.How to design and optimize TENGs to cover all characteristic water wave energies and achieve efficient energy utilization is emergent.In this paper,we carefully designed and fabricated a columnar multi-layer sliding TENG(CMLS-TENG)that can harvest water wave energy independent of wave height and direction.Drive rods with a hollow acrylic spherical shell were introduced to deliver wave energy,ensuring that the CMLS-TENG can work in all directions from 0°to 360°.Based on the sliding structure,switching the optimized CMLS-TENG is independent of wave heights.The optimized CMLS-TENG can achieve a total power density of 730 mW/m^(3) at a wave height of only 4.8 cm regardless of wave direction,which can illuminate multiple light-emitting diodes(LEDs)to provide lighting and provide power to a watch and a hygrometer for temperature and humidity monitoring.This work provides new choices and hopes for the effective collection of full-range water wave energy.展开更多
The columnar jointed rock mass(CJR), composed of polygonal cross-sectional columns cut by several groups of joints in various directions, was exposed during the excavations of the Baihetan hydropower station, China. I...The columnar jointed rock mass(CJR), composed of polygonal cross-sectional columns cut by several groups of joints in various directions, was exposed during the excavations of the Baihetan hydropower station, China. In order to investigate the unloading performances and the stability conditions during excavation of the columns, an experimental field study was performed. Firstly, on-site investigations indicated that the geotechnical problems, including rock relaxation, cracking and collapse, were the most prominent for the CJR Class I that contains intensive joint network and the smallest column sizes.Comprehensive field tests, including deformation measurement by multi-point extensometers, ultrasonic wave testing, borehole television observation and stress monitoring of rock anchors, revealed that the time-dependent relaxation of the CJRs was marked. The practical excavation experiences for the Baihetan columnar jointed rock masses, such as blasting scheme, supporting time of shotcrete and rock bolts, were presented in the excavations of the diversion tunnels. These detailed investigations and practical construction experiences can provide helpful information for similar geotechnical works in jointed rock mass.展开更多
The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of...The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of CJRM is important for engineering construction.The Voronoi diagram and three-dimensional printing technology were used to make an irregular columnar jointed mold,and the irregular CJRM(ICJRM)specimens with different dip directions and dip angles were prepared.Uniaxial compression tests were performed,and the anisotropic strength and deformation characteristics of ICJRM were described.The failure modes and mechanisms were revealed in accordance with the final appearances of the ICJRM specimens.Based on the model test results,the empirical correlations for determining the field deformation and strength parameters of CJRM were derived using the dip angle and modified joint factor.The proposed empirical equations were used in the Baihetan Project,and the calculated mechanical parameters were compared with the field test results and those obtained from the tunneling quality index method.Results showed that the deformation parameters determined by the two proposed methods are all consistent with the field test results,and these two methods can also estimate the strength parameters effectively.展开更多
According to the hydraulic calculation principles of the orifice outflow, the discharge capacity of the columnar reversing gate under the partial opening condition was calculated and checked. Using ANSYS, a large fini...According to the hydraulic calculation principles of the orifice outflow, the discharge capacity of the columnar reversing gate under the partial opening condition was calculated and checked. Using ANSYS, a large finite element analysis software, the discharge process was simulated. The distribution rule of the velocities in the gate chamber and downstream channel was obtained. An FEM model of the columnar reversing gate was built, and the natural vibration properties of the gate were analyzed. Based on the Westergaard added mass method, the added mass caused by the fluid-structure coupling motion was taken into account, and the effects of the coupling interaction were discussed. The results show that the size of the small gates meets the demand for discharge capacity, the current in the gate chamber is quite turbulent, the trunnion and arms are obviously impacted by flow, and the effects of water on vibration characteristics are remarkable. The study provides a reference for the design and calculation of gates of the same type.展开更多
The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C ...The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C to 400°C was investigated. The microstructure evolution during the aging treatment was characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that the plate-like bainite precipitates distribute homogeneously within austenitic grains and at grain boundaries. The volume fraction of bainite increases with the increase in aging temperature and aging time, which substantially improves the martensitic transformation critical stress of the alloy, whereas the bainite only slightly affects the superelasticity. This behavior is attributed to a coherent relationship between the bainite and the austenite, as well as to the bainite and the martensite exhibiting the same crystal structure. The variations of the martensitic transformation critical stress and the superelasticity of columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with aging-temperature and aging time are described by the Austin-Rickett equation, where the activation energy of bainite precipitation is 77.2 kJ ·mol1. Finally, a columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with both excellent superelasticity（5%-9%） and high martensitic transformation critical stress（443-677 MPa） is obtained through the application of the appropriate aging treatments.展开更多
The characteristics of novel Nd-Fe （Ni, Co, Al ）-B microstructure prepared by strip casting technique were studied. The novel microstructure was observed using scanning electron microscope （SEM） and transmission e...The characteristics of novel Nd-Fe （Ni, Co, Al ）-B microstructure prepared by strip casting technique were studied. The novel microstructure was observed using scanning electron microscope （SEM） and transmission electron microscope （TEM）. Along the direction of heat flow, there are two kinds of different microstructures. Close to the wheel side, there is a thick layer containing many polygonal Nd2Fe14B grains. Near the free surface side, however, there are relative uniform platelike Nd2Fe14B grains whose growth direction is not completely the direction of the heat flow during solidification. The formation of the novel microstructure is presumed to be the contribution of the special temperature field and Ni component.展开更多
文摘The homogeneity of low alloy steels continuous casting billet obtained under different technological conditions has been investigated by original position statistic distribution analysis technique. On the basis of systematic analysis of ten thousands primary optical signals at the corresponding original positions, the quantitative statistic distribution information of each element was obtained. The biggest degrees of segregation of low alloy steel continuous casting billet were calculated accurately according to the quantitative distribution maps of the contents. It was suggested that the weight ratio in a certain content range was used to judge the homogeneity of the materials, and the two models —— the total weight ratio of contents (the degree of statistic homogeneity, H) within the permissive content range (C0±R) and the median value confidence extension ratio (the degree of statistic segregation, S) at 95% of confidence limit of weight ratio —— were put forward. The two models reflect the composition and state distribution regularity of the metal materials in a large region. The difference between the sample with high columnar crystal and the sample with high equiaxed crystal has been studied by using the two models.
基金supported by the China Geological Survey (grant numbers DD20160083 and DD20160344-05)the National Key Research and Development Program of China (grant numbers 2018YFC0603701)Fundamental Research Funds for Central Public Welfare Research Institutes (grant numbers CAGS-YWF201706)
文摘The West Junggar of the western Central Asian Orogenic Belt is one of the typical regions in the term of ocean subduction, contraction and continental growth in the Late Paleozoic. However, it is still controversial on the exact time of ocean-continent transition so far. This study investigates rhyolites with columnar joint in the West Junggar for the first time.Based on zircon U-Pb dating, we determined that the ages of the newly-discovered rhyolites are between 303.6 and 294.5 Ma, belonging to Late Carboniferous–Early Permian, which is the oldest rhyolite with columnar joint preserved in the world at present. Geochemical results show that the characteristics of the major element compositions include a high content of SiO_2(75.78–79.20 wt%) and a moderate content of Al_2O_3(12.21–13.19 wt%). The total alkali content(K_2O +Na_2O) is 6.14–8.05 wt%, among which K_2O is 2.09–4.72 wt% and the rate of K_2O/Na_2O is 0.38–3.05. Over-based minerals such as Ne, Lc, and Ac do not appear. The contents of TiO_2(0.09–0.24 wt%), CaO(0.15–0.99 wt%) and MgO(0.06–0.18 wt%) are low. A/CNK=0.91–1.68, A/NK=1.06–1.76, and as such, these are associated with the quasi-aluminum-weak peraluminous high potassium calc-alkaline and some calc-alkaline magma series. These rhyolites show a significant negative Eu anomaly with relative enrichment of LREE and LILE(Rb, Ba, Th, U, K) and depletion of Sr, HREE and HFSE(Nb, Ta, Ti, P). These rhyolites also have the characteristics of an A2-type granite, similar to the Miaoergou batholith,which indicates they both were affected by post-orogenic extension. Combining petrological, zircon U-Pb dating and geochemical characteristics of the rhyolites, we conclude that the specific time of ocean-continent transition of the West Junggar is the Late Carboniferous–Early Permian.
基金Item Sponsored by National Natural Science Foundation of China(50674064,50734008)
文摘A new approach to applying the electric current pulse （ECP） with parallel electrodes to the promotion of the transition from columnar crystal to equiaxed crystal and the improvement of macrosegregation was introduced. The ECP was applied to different stages of the solidification. The results showed that the application of the ECP in both the initial stage （the thickness of solidified shell reached 2 mm approximately） and the late stage （the thickness of solidified shell reached 14 mm approximately） of solidification can promote the columnar to equiaxed transition （CET）. The analysis showed that during solidification, a large number of nuclei around the upper surface fell off due to ECP, which subsequently showered on the melt and impinged the growth front of the columnar crystal. Therefore, the CEToccurred. In addition, this method was also employed to influence the solidification process of bearing steel, and the results showed that the structure was changed from columnar crystal to equiaxed crystal, indicating that ECP can enhance the homogeneity of structure and composition of bearing steel.
基金Projects(50911130366, 50979030) supported by the National Natural Science Foundation of China
文摘From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the AUTOCAD model into 3DEC (3-dimensional distinct element code) model was developed, and a numerical model was established in 3DEC. Moreover, the results of triaxial compression tests of columnar jointed rock masses were simulated numerically. The REV (representative element volume) scale was studied, and the result shows that the REV size is 3 m × 3 m. The proposed approach, the established model and the numerical simulation were applied to study the macro-mechanical properties and the equivalent strength parameters of the columnar jointed rock mass. The numerical simulation results are in good accordance with the in-situ test results.
基金Project supported by the National Natural Science Foundation of China （No. 50473062）, Youth Foundation of Sichuan Province （No. 04ZQ026-044）.
文摘A series of new trialkoxytrialkanoyloxytriphenylene TP（OCnH2n＋1）3（OCOCmH2m＋1）3 （5a-5e） （n =m＋1 =4- 8） discotic liquid crystals were prepared and their mesomorphic properties were investigated using differential scanning calorimetry （DSC） and polarizing optical microscopy （POM）. The symmetrical and shorter chain triphenylenes display higher melting points and clearing points, more highly ordered and stable columnar mesophase than the asymmetrical and longer chain triphenylenes respectively.
基金Project supported by the National Natural Science Foundation of China （Nos. 50473062, 50673069）, the Sichuan Province Youth Foundation （No. 04-ZQ026-044） and the Research Project of Sichuan Province （No. 05GG009-005）, China.
文摘Small change in chemical structure of discotic liquid crystals can cause big difference in their mesomorphism. Replacing of the alkoxy peripheral chains of triphenylene by oxygen-atom containing ester chains would result in novel mesomorphism. A series of mixed tail triphenylenes containing propoxyacetyloxy and alkoxy, abbreviated as C18H6（OCnH2n＋1）3（OCOCH2OC3H7）3, n=4-8, and hexa（propyloxyacetyloxy）triphenylene, C18H6（OCOCH2OC3H7）6 were synthesized. Thermal gravimetry analysis （TGA） of three discogens showed that they had good thermal stability till 350 ℃. The mesomorphism was investigated through differential scanning calorimetry （DSC） and polarized optical microscopy （POM）. The preliminary X-ray diffraction （XRD） results of one compound showed that it exhibited ordered hexagonal columnar （Colho） mesophase. These mixed tail triphenylene derivatives possessed much stable Colho mesophase and wider mesophase ranges than their hexaalkoxytriphenylene C18H6（OR）6 and hexaalkanoyloxytriphenylene C18H6（OCOR＇）6 analogues. The asymmetrical compounds 2,6,11-trialkoxy-3,7,10-tri（2-propyloxyacetyloxy）triphenylenes with n=5-8 displayed higher clearing points and wider temperature ranges than their symmetrical isomers 2,6,10-trialkoxy-3,7,11-tri（2-propyloxyacetyloxy）- triphenylenes, while C18H6（OCOCH2OC3H7）6 had the highest clearing point due to the β-oxygen-atom effect.
基金Supported by the National Basic Research Program of China (Grant No. 2006CB605200)the National High Technology Research and Development Program of China (Grant No. 2006AA03Z506)+1 种基金the National Natural Science Foundation of China (Grant Nos. 50674008 and 50634010)the Program for New Century Excellent Talents in University of China (Grant No. NCET-06-0083)
文摘The microstructure and mechanical properties of Cu-12wt%Al alloy wires which are composed of continuous columnar crystals after dieless drawing forming at drawing speed of 1.0–1.4 mm/s and deformation temperature of 600–900°C were analyzed, and deformation behavior of the alloy during dieless drawing forming was experimentally investigated. The results showed that in the above-mentioned conditions, recrystallization phenomenon was not found during dieless drawing forming. When a drawing speed of 1.0 mm/s was used, the grain boundaries were out of straight gradually with increasing deformation temperature from 600°C to 900°C, and tensile strength of the dieless drawn Cu-12wt%Al alloy wires increased while elongations decreased with increasing deformation temperature. At drawing speed of 1.1–1.2 mm/s and deformation temperature of 600°C, the effect of dieless drawing forming process on the microstructure of the alloy was inconspicuous, and when drawing speed was up to 1.3–1.4 mm/s, the grain boundaries of continuous columnar crystals became zigzag while there was little effect of drawing speed of 1.1–1.4 mm/s on the elongation and tensile strength of the alloy wires.
基金Supported by the National Natural Science Foundation of China(Grant Nos.50473062,50673069,and 50811140156)
文摘Connecting two discotic mesogens via a spacer not only stabilizes the columnar mesophase but also leads to the formation of glass columnar phase, and therefore improves the physical properties of discotic liquid crystals as organic semiconductor. Here, we report the synthesis of eight diacetylene-bridged triphenylene discotic liquid crystal dimers, [C18H6(OC n H2n+1)4(OMe)O2C?C8H16?C≡C?]2, 3(n), (n = 4–8), [C18H6(OC6H13)5O2C?C8H16?C≡C?]2, 6 and [C18H6(OC6H13)5O?(CH2)m?C≡C?]2, 8(m), (m = 1, 3) by Eglinton coupling reaction. The thermotropic liquid crystal properties were studied by differential scanning calorimetry and polarized optical microscopy. The results are showed as follows: the length of peripheral alkyl chains of triphenylene influenced properties of liquid crystal dimers; dimers 3(n) (n = 5–8) and 6 had glass columnar phase, and no crystallization was observed above ?50°C for all the triphenylene dimers; compared with 3(6), 6 showed higher molecular symmetry, more stable columnar mesophase and wider mesophase range. The connecting group, length and rigidity of spacer had important influence on the mesomorphism of diacetylene-bridged triphenylene discotic liquid crystal dimers.
文摘Considering the S L interface morphology stability, the S L interface energy, the Joule heat produced by electric current at the S L interface, and the change of solute concentration at the S L interface indirectly caused by electric current, the mechanism of reduction of columnar dendrite spacing in unidirectional solidification caused by electric current passing through solid liquid interface was studied. The following conclusions can be drawn that: 1) under sub rapid solidification condition, increasing electric current density will improve the stability of S L interface, thus decreasing the columnar dendrite spacing; 2)there are two ways by which the increase of electric current decreases the columnar dendrite spacing, one is promoting the splitting of the protruding tips at the S L interface, the other is promoting the forming of new convex parts at the bottom of the concave interface.[
文摘BACKGROUND Recently,research has linked Helicobacter pylori(H.pylori)stomach infection to colonic inflammation,mediated by toxin production,potentially impacting colorectal cancer occurrence.AIM To investigate the risk factors for post-colon polyp surgery,H.pylori infection,and its correlation with pathologic type.METHODS Eighty patients who underwent colon polypectomy in our hospital between January 2019 and January 2023 were retrospectively chosen.They were then randomly split into modeling(n=56)and model validation(n=24)sets using R.The modeling cohort was divided into an H.pylori-infected group(n=37)and an H.pylori-uninfected group(n=19).Binary logistic regression analysis was used to analyze the factors influencing the occurrence of H.pylori infection after colon polyp surgery.A roadmap prediction model was established and validated.Finally,the correlation between the different pathological types of colon polyps and the occurrence of H.pylori infection was analyzed after colon polyp surgery.RESULTS Univariate results showed that age,body mass index(BMI),literacy,alcohol consumption,polyp pathology type,high-risk adenomas,and heavy diet were all influential factors in the development of H.pylori infection after intestinal polypectomy.Binary multifactorial logistic regression analysis showed that age,BMI,and type of polyp pathology were independent predictors of the occurrence of H.pylori infection after intestinal polypectomy.The area under the receiver operating characteristic curve was 0.969[95%confidence interval(95%CI):0.928–1.000]and 0.898(95%CI:0.773–1.000)in the modeling and validation sets,respectively.The slope of the calibration curve of the graph was close to 1,and the goodness-of-fit test was P>0.05 in the two sets.The decision analysis curve showed a high rate of return in both sets.The results of the correlation analysis between different pathological types and the occurrence of H.pylori infection after colon polyp surgery showed that hyperplastic polyps,inflammatory polyps,and the occurrenc
文摘BACKGROUND Neutrophil-lymphocyte ratio(NLR),fibrosis index based on four factors(Fib4),aspartate aminotransferase-to-platelet ratio index(APRI)can be used for prognostic evaluation of hepatocellular carcinoma.However,no study has established an individualized prediction model for the prognosis of hepatocellular carcinoma based on these factors.AIM To screen the factors that affect the prognosis of hepatocellular carcinoma and establish a nomogram model that predicts postoperative liver failure after hepatic resection in patients with hepatocellular carcinoma.METHODS In total,220 patients with hepatocellular carcinoma treated in our hospital from January 2022 to January 2023 were selected.They were divided into 154 participants in the modeling cohort,and 66 in the validation cohort.Comparative analysis of the changes in NLR,Fib4,and APRI levels in 154 patients with hepatocellular carcinoma before liver resection and at 3 mo,6 mo,and 12 mo postoperatively was conducted.Binary logistic regression to analyze the influencing factors on the occurrence of liver failure in hepatocellular carcinoma patients,roadmap prediction modeling,and validation,patient work characteristic curves(ROCs)to evaluate the predictive efficacy of the model,calibration curves to assess the consistency,and decision curve analysis(DCA)to evaluate the model’s validity were also conducted.RESULTS Binary logistic regression showed that Child-Pugh grading,Surgical site,NLR,Fib4,and APRI were all risk factors for liver failure after hepatic resection in patients with hepatocellular carcinoma.The modeling cohort built a column-line graph model,and the area under the ROC curve was 0.986[95%confidence in terval(CI):0.963-1.000].The patients in the validation cohort utilized the column-line graph to predict the probability of survival in the validation cohort and plotted the ROC curve with an area under the curve of the model of 0.692(95%CI:0.548-0.837).The deviation of the actual outcome curves from the calibration curves of the column-line plots gen
文摘Columnar nanocrystalline aluminum nitride(cnc-AlN) thin films with(002) orientation and uniform texture have been deposited successfully on large silicon wafers by RF reactive magnetron sputtering.At the optimum sputtering parameters, the deposited cnc-AlN thin films show a c-axis preferred orientation with a crystallite size of about 28 nm and surface roughness(RMS) of about 1.29 nm. The cnc-AlN thin films were well transparent with an optical band gap about 4.8 e V, and the residual compressive stress and the defect density in the film have been revealed by Ramon spectroscopy. Moreover, piezoelectric performances of the cnc-AlN thin films executed effectively in a film bulk acoustic resonator structure.
基金supported by the Major State Basic Research Development Program of China (No.2011CB012900)the National Natural Science Foundation of China (No.51374144)the Shanghai Rising-Star Program (No.14QA1402300)
文摘Isothermal hot compression tests of as-cast high-Cr ultra-super-critical（USC） rotor steel with columnar grains perpendicular to the compression direction were carried out in the temperature range from 950 to 1250°C at strain rates ranging from 0.001 to 1 s^（-1）. The softening mechanism was dynamic recovery（DRV） at 950°C and the strain rate of 1 s^（-1）, whereas it was dynamic recrystallization（DRX） under the other conditions. A modified constitutive equation based on the Arrhenius model with strain compensation reasonably predicted the flow stress under various deformation conditions, and the activation energy was calculated to be 643.92 kJ ×mol^（-1）. The critical stresses of dynamic recrystallization under different conditions were determined from the work-hardening rate（θ）–flow stress（σ） and-θ/σ–σ curves. The optimum processing parameters via analysis of the processing map and the softening mechanism were determined to be a deformation temperature range from 1100 to 1200°C and a strain-rate range from 0.001 to 0.08 s^（-1）, with a power dissipation efficiency η greater than 31%.
基金supported by the National Key R&D Project from Ministry of Science and Technology,China(No.2021YFA1201603)the National Natural Science Foundation of China(Nos.52073032 and 52192611)the Fundamental Research Funds for the Central Universities.
文摘The ocean,with its highly variable and complex meteorological conditions,harbors enormous renewable resources.Triboelectric nanogenerators(TENGs),which possess unique advantages,show exciting prospects in water wave energy collection.How to design and optimize TENGs to cover all characteristic water wave energies and achieve efficient energy utilization is emergent.In this paper,we carefully designed and fabricated a columnar multi-layer sliding TENG(CMLS-TENG)that can harvest water wave energy independent of wave height and direction.Drive rods with a hollow acrylic spherical shell were introduced to deliver wave energy,ensuring that the CMLS-TENG can work in all directions from 0°to 360°.Based on the sliding structure,switching the optimized CMLS-TENG is independent of wave heights.The optimized CMLS-TENG can achieve a total power density of 730 mW/m^(3) at a wave height of only 4.8 cm regardless of wave direction,which can illuminate multiple light-emitting diodes(LEDs)to provide lighting and provide power to a watch and a hygrometer for temperature and humidity monitoring.This work provides new choices and hopes for the effective collection of full-range water wave energy.
基金the financial support from the International Partnership Program of Chinese Academy of Sciences(Grant No.115242KYSB20160017)the Key Project of Natural Science Foundation of China(Grant No.11232014)National Natural Science Foundation of China(Grant No.51379202)
文摘The columnar jointed rock mass(CJR), composed of polygonal cross-sectional columns cut by several groups of joints in various directions, was exposed during the excavations of the Baihetan hydropower station, China. In order to investigate the unloading performances and the stability conditions during excavation of the columns, an experimental field study was performed. Firstly, on-site investigations indicated that the geotechnical problems, including rock relaxation, cracking and collapse, were the most prominent for the CJR Class I that contains intensive joint network and the smallest column sizes.Comprehensive field tests, including deformation measurement by multi-point extensometers, ultrasonic wave testing, borehole television observation and stress monitoring of rock anchors, revealed that the time-dependent relaxation of the CJRs was marked. The practical excavation experiences for the Baihetan columnar jointed rock masses, such as blasting scheme, supporting time of shotcrete and rock bolts, were presented in the excavations of the diversion tunnels. These detailed investigations and practical construction experiences can provide helpful information for similar geotechnical works in jointed rock mass.
基金This work was supported by the Fundamental Research Funds for the Central Universities,the Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX21_0487)the National Natural Science Foundation of China(Grant Nos.41831278,and 51579081).
文摘The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of CJRM is important for engineering construction.The Voronoi diagram and three-dimensional printing technology were used to make an irregular columnar jointed mold,and the irregular CJRM(ICJRM)specimens with different dip directions and dip angles were prepared.Uniaxial compression tests were performed,and the anisotropic strength and deformation characteristics of ICJRM were described.The failure modes and mechanisms were revealed in accordance with the final appearances of the ICJRM specimens.Based on the model test results,the empirical correlations for determining the field deformation and strength parameters of CJRM were derived using the dip angle and modified joint factor.The proposed empirical equations were used in the Baihetan Project,and the calculated mechanical parameters were compared with the field test results and those obtained from the tunneling quality index method.Results showed that the deformation parameters determined by the two proposed methods are all consistent with the field test results,and these two methods can also estimate the strength parameters effectively.
文摘According to the hydraulic calculation principles of the orifice outflow, the discharge capacity of the columnar reversing gate under the partial opening condition was calculated and checked. Using ANSYS, a large finite element analysis software, the discharge process was simulated. The distribution rule of the velocities in the gate chamber and downstream channel was obtained. An FEM model of the columnar reversing gate was built, and the natural vibration properties of the gate were analyzed. Based on the Westergaard added mass method, the added mass caused by the fluid-structure coupling motion was taken into account, and the effects of the coupling interaction were discussed. The results show that the size of the small gates meets the demand for discharge capacity, the current in the gate chamber is quite turbulent, the trunnion and arms are obviously impacted by flow, and the effects of water on vibration characteristics are remarkable. The study provides a reference for the design and calculation of gates of the same type.
基金financially supported by the National Natural Science Foundation of China (Nos. 51574027 and 51604206)the Financial Support from the State Key Laboratory for Advanced Metals and Materials (No. 2016Z-22)
文摘The effect of aging treatment on the superelasticity and martensitic transformation critical stress in columnar-grained Cu_（71）Al_（18）Mn_（11） shape memory alloy（SMA） at the temperature ranging from 250°C to 400°C was investigated. The microstructure evolution during the aging treatment was characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The results show that the plate-like bainite precipitates distribute homogeneously within austenitic grains and at grain boundaries. The volume fraction of bainite increases with the increase in aging temperature and aging time, which substantially improves the martensitic transformation critical stress of the alloy, whereas the bainite only slightly affects the superelasticity. This behavior is attributed to a coherent relationship between the bainite and the austenite, as well as to the bainite and the martensite exhibiting the same crystal structure. The variations of the martensitic transformation critical stress and the superelasticity of columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with aging-temperature and aging time are described by the Austin-Rickett equation, where the activation energy of bainite precipitation is 77.2 kJ ·mol1. Finally, a columnar-grained Cu_（71）Al_（18）Mn_（11） SMA with both excellent superelasticity（5%-9%） and high martensitic transformation critical stress（443-677 MPa） is obtained through the application of the appropriate aging treatments.
文摘The characteristics of novel Nd-Fe （Ni, Co, Al ）-B microstructure prepared by strip casting technique were studied. The novel microstructure was observed using scanning electron microscope （SEM） and transmission electron microscope （TEM）. Along the direction of heat flow, there are two kinds of different microstructures. Close to the wheel side, there is a thick layer containing many polygonal Nd2Fe14B grains. Near the free surface side, however, there are relative uniform platelike Nd2Fe14B grains whose growth direction is not completely the direction of the heat flow during solidification. The formation of the novel microstructure is presumed to be the contribution of the special temperature field and Ni component.
