The mechanical properties of transformation induced plasticity （TRIP） steel are strongly affected by the conditions of iso-thermal bainitic processing. The multiphase microstructure of TRIP steel under different con...The mechanical properties of transformation induced plasticity （TRIP） steel are strongly affected by the conditions of iso-thermal bainitic processing. The multiphase microstructure of TRIP steel under different conditions of isothermal bainitic processing was investigated using OM,SEM,XRD and TEM. The volume fraction of retained austenite and the carbon content in austenite were determined quantitatively using X-ray diffraction patterns. The relationship between mechanical properties and isothermal bainitic processing parameters was investigated. The stability of retained austenite was analyzed by the volume fraction of retained austenite and the carbon content in retained austenite. The experimental results show that the multiphase microstructure consists of ferrite,bainite and metastable retained austenite.To obtain good mechanical properties,the optimal conditions of isothermal bainitic temperature and holding time are 410-430°C and 180-240 s,respectively. After isothermal bainitic processing under the optimal conditions,the corresponding volume fraction of retained austenite is 5vol%-15vol%,which can provide enough retained austenite and plastic stability for austenite with high carbon content.展开更多
With the two sublattices model, equilibrium compositions of ferrite (α) and austenite (γ) phases, as well as the volume percent of austenite (γ) in different TRIP steels are calculated. Concentration profiles of ca...With the two sublattices model, equilibrium compositions of ferrite (α) and austenite (γ) phases, as well as the volume percent of austenite (γ) in different TRIP steels are calculated. Concentration profiles of carbon, manganese, aluminum and silicon in these steels are also estimated under the lattice fixed frame of reference so as to identify if the equilibrium state is obtained. Through the comparison between the profiles after different time diffusion, the distribution of elements in phases is exhibited and the complex effect due to the mutual interaction of the elements on diffusion is discussed.展开更多
Bead-on-plate CO2 laser welding of 1 000 MPa grade transformation induced plasticity （TRIP） steel was conducted under different welding powers, welding speeds and shield gases. The macrostructural and microstructura...Bead-on-plate CO2 laser welding of 1 000 MPa grade transformation induced plasticity （TRIP） steel was conducted under different welding powers, welding speeds and shield gases. The macrostructural and microstructural features of the welded joint were investigated. The increase of welding speed reduced the width of the weld bead and the porosities in the weld bead resulting from the different flow mode of melted metal in weld pool. The decrease of welding power or use of shield gas of helium also contributed to the reduction of porosity in the weld bead due to the alleviation of induced plasma formation, thus stabilizing the keyhole. The porosity formation intimately correlated with the evaporation of alloy element Mn in the base metal. The laser welded metal had same martensite microstructure as that of water-quenched base metal. The welding parameters which increased cooling rate all led to fine microstructures of the weld bead.展开更多
Microstructures and mechanical properties of Nd ： YAG laser welded transformation induced plasticity （TRIP） steel with tensile strength of 645 MPa were studied. Due to high cooling speed of laser welding, the weld ...Microstructures and mechanical properties of Nd ： YAG laser welded transformation induced plasticity （TRIP） steel with tensile strength of 645 MPa were studied. Due to high cooling speed of laser welding, the weld metal mainly consists of martensite different from the base metal, which is composed of ferrite matrix with bainite and a little retained austenite. Therefore, the weld metal has maximum hardness at welded joint. The yield strength and tensile strength of welded specimens tested perpendicular to weld line were almost equal to those of the base metal. But the yield strength and tensile strength of welded specimens tested parallel with weld line were a little higher than those of the base metal. The formability of laser welded TRIP steel was decreased compared with that of the base metal.展开更多
文摘The mechanical properties of transformation induced plasticity （TRIP） steel are strongly affected by the conditions of iso-thermal bainitic processing. The multiphase microstructure of TRIP steel under different conditions of isothermal bainitic processing was investigated using OM,SEM,XRD and TEM. The volume fraction of retained austenite and the carbon content in austenite were determined quantitatively using X-ray diffraction patterns. The relationship between mechanical properties and isothermal bainitic processing parameters was investigated. The stability of retained austenite was analyzed by the volume fraction of retained austenite and the carbon content in retained austenite. The experimental results show that the multiphase microstructure consists of ferrite,bainite and metastable retained austenite.To obtain good mechanical properties,the optimal conditions of isothermal bainitic temperature and holding time are 410-430°C and 180-240 s,respectively. After isothermal bainitic processing under the optimal conditions,the corresponding volume fraction of retained austenite is 5vol%-15vol%,which can provide enough retained austenite and plastic stability for austenite with high carbon content.
文摘With the two sublattices model, equilibrium compositions of ferrite (α) and austenite (γ) phases, as well as the volume percent of austenite (γ) in different TRIP steels are calculated. Concentration profiles of carbon, manganese, aluminum and silicon in these steels are also estimated under the lattice fixed frame of reference so as to identify if the equilibrium state is obtained. Through the comparison between the profiles after different time diffusion, the distribution of elements in phases is exhibited and the complex effect due to the mutual interaction of the elements on diffusion is discussed.
文摘Bead-on-plate CO2 laser welding of 1 000 MPa grade transformation induced plasticity （TRIP） steel was conducted under different welding powers, welding speeds and shield gases. The macrostructural and microstructural features of the welded joint were investigated. The increase of welding speed reduced the width of the weld bead and the porosities in the weld bead resulting from the different flow mode of melted metal in weld pool. The decrease of welding power or use of shield gas of helium also contributed to the reduction of porosity in the weld bead due to the alleviation of induced plasma formation, thus stabilizing the keyhole. The porosity formation intimately correlated with the evaporation of alloy element Mn in the base metal. The laser welded metal had same martensite microstructure as that of water-quenched base metal. The welding parameters which increased cooling rate all led to fine microstructures of the weld bead.
文摘Microstructures and mechanical properties of Nd ： YAG laser welded transformation induced plasticity （TRIP） steel with tensile strength of 645 MPa were studied. Due to high cooling speed of laser welding, the weld metal mainly consists of martensite different from the base metal, which is composed of ferrite matrix with bainite and a little retained austenite. Therefore, the weld metal has maximum hardness at welded joint. The yield strength and tensile strength of welded specimens tested perpendicular to weld line were almost equal to those of the base metal. But the yield strength and tensile strength of welded specimens tested parallel with weld line were a little higher than those of the base metal. The formability of laser welded TRIP steel was decreased compared with that of the base metal.
