针对流水线型逐次逼近模数转换器(Pipelined SAR ADC)中残差放大器的核心运放功耗过高,从而严重限制ADC能效上限的问题,本文提出了一种新型的基于CMOS开关的自偏置全差分环形放大器(CMOS Self-biased Fully Differential Ring Amplifier...针对流水线型逐次逼近模数转换器(Pipelined SAR ADC)中残差放大器的核心运放功耗过高,从而严重限制ADC能效上限的问题,本文提出了一种新型的基于CMOS开关的自偏置全差分环形放大器(CMOS Self-biased Fully Differential Ring Amplifier,CSFRA),来替代传统运放。CSFRA通过引入CMOS开关自偏置和全差分结构,同时在非放大时序中关断电路,降低了残差放大器功耗。基于所提CSFRA,配合可降低开关功耗的检测和跳过切换方案,设计了一款12 Bit 10 MS/s的Pipelined SAR ADC。该电路基于MXIC L18B 180 nm CMOS工艺实现,实验结果表明,在10 MS/s的采样率下,该电路的SFDR和SNDR分别为75.3 dB和61.3 dB,功耗仅为944μW,其中CSFRA功耗仅为368μW。展开更多
A low-power 14-bit 150MS/s an- alog-to-digital converter （ADC） is present- ed for communication applications. Range scaling enables a maximal 2-Vp-p input with a single-stage opamp adopted. Opamp and capacitor shari...A low-power 14-bit 150MS/s an- alog-to-digital converter （ADC） is present- ed for communication applications. Range scaling enables a maximal 2-Vp-p input with a single-stage opamp adopted. Opamp and capacitor sharing between the first multi- plying digital-to-analog converter （MDAC） and the second one reduces the total opamp power further. The dedicated sample-and- hold amplifier （SHA） is removed to lower the power and the noise. The blind calibration of linearity errors is proposed to improve the per- formance. The prototype ADC is fabricated in a 130rim CMOS process with a 1.3-V supply voltage. The SNDR of the ADC is 71.3 dB with a 2.4 MHz input and remains 68.5 dB for a 120 MHz input. It consumes 85 roW, which includes 57 mW for the ADC core, 11 mW for the low jitter clock receiver and 17 mW for the high-speed reference buffer.展开更多
A low power 10-bit 125-MSPS charge-domain(CD) pipelined analog-to-digital converter(ADC) based on MOS bucket-brigade devices(BBDs) is presented.A PVT insensitive boosted charge transfer(BCT) that is able to reject the...A low power 10-bit 125-MSPS charge-domain(CD) pipelined analog-to-digital converter(ADC) based on MOS bucket-brigade devices(BBDs) is presented.A PVT insensitive boosted charge transfer(BCT) that is able to reject the charge error induced by PVT variations is proposed.With the proposed BCT,the common mode charge control circuit can be eliminated in the CD pipelined ADC and the system complexity is reduced remarkably.The prototype ADC based on the proposed BCT is realized in a 0.18μm CMOS process,with power consumption of only 27 mW at 1.8-V supply and active die area of 1.04 mm^2.The prototype ADC achieves a spurious free dynamic range(SFDR) of 67.7 dB,a signal-to-noise ratio(SNDR) of 57.3 dB,and an effective number of bits(ENOB) of 9.0 for a 3.79 MHz input at full sampling rate.The measured differential nonlinearity(DNL) and integral nonlinearity (INL) are +0.5/-0.3 LSB and +0.7/-0.55 LSB,respectively.展开更多
A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the prec...A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the precision of CD pipelined ADCs is restricted by the variation in input CM charge, which can compensate for CM charge errors caused by a variation in CM charge input in real time. Based on the feed-forward CM charge control circuit, a 12-bit 250-MS/s CD pipelined ADC is designed and realized using a 1P6M 0.18-μm CMOS process. The ADC achieved a Spurious Free Dynamic Range （SFDR） of 78.1 dB and a Signal-to-Noise-and-Distortion Ratio （SNDR） of 64.6 dB for a 20.1-MHz input; a SFDR of 74.9 dB and SNDR of 62.0 dB were achieved for a 239.9-MHz input at full sampling rate. The variation in signal-to-noise ratio was less than 3 dB over a 0-1.2 V input CM voltage range. The power consumption of the prototype ADC is only 85 mW at 1.8 V supply, and it occupies an active die area of 2.24 mm^2.展开更多
A CMOS fluorescent detector system for biological experiment is presented. This system integrates a CMOS compatible photodiode, a capacitive trans-impedance amplifier （CTIA）, and a 12 bit pipelined analog-to- digita...A CMOS fluorescent detector system for biological experiment is presented. This system integrates a CMOS compatible photodiode, a capacitive trans-impedance amplifier （CTIA）, and a 12 bit pipelined analog-to- digital converter （ADC）, and is implemented in a 0.18μm standard CMOS process. Some special techniques, such as a ＂contact imaging＂ detecting method, pseudo-differential architecture, dummy photodiodes, and a T-type reset switch, are adopted to achieve low-level sensing application. Experiment results show that the Nwell/Psub photodiode with CTIA pixel achieves a sensitivity of 0.1 A/W at 515 nm and a dark current of 300 fA with 300 mV reverse biased voltage. The maximum differential and integral nonlinearity of the designed ADC are 0.8 LSB and 3 LSB, respectively. With an integrating time of 50 ms, this system is sensitive to the fluorescence emitted by the fluorescein solution with concentration as low as 20 ng/mL and can generate 7 fA photocurrent. This chip occupies 3 mm^2 and consumes 37 mW.展开更多
This paper presents a 12-bit 100 MS/s CMOS pipelined analog-to-digital converter （ADC） with digital background calibration. A large magnitude calibration signal is injected into the multiplying digital-to-analog con...This paper presents a 12-bit 100 MS/s CMOS pipelined analog-to-digital converter （ADC） with digital background calibration. A large magnitude calibration signal is injected into the multiplying digital-to-analog converter （MDAC） while the architecture of the MDAC remains unchanged. When sampled at 100 MS/s, it takes only 2.8 s to calibrate the 12-bit prototype ADC and achieves a peak spurious-free dynamic range of 85 dB and a peak signal-to-noise plus distortion ratio of 66 dB with 2 MHz input. Integral nonlinearity is improved from 1.9 to 0.6 least significant bits after calibration. The chip is fabricated in a 0.18μm CMOS process, occupies an active area of 2.3 × 1.6 mm^2, and consumes 205 mW at 1.8 V.展开更多
For polar codes,the performance of successive cancellation list(SCL)decoding is capable of approaching that of maximum likelihood decoding.However,the existing hardware architectures for the SCL decoding suffer from h...For polar codes,the performance of successive cancellation list(SCL)decoding is capable of approaching that of maximum likelihood decoding.However,the existing hardware architectures for the SCL decoding suffer from high hardware complexity due to calculating L decoding paths simultaneously,which are unfriendly to the devices with limited logical resources,such as field programmable gate arrays(FPGAs).In this paper,we propose a list-serial pipelined hardware architecture with low complexity for the SCL decoding,where the serial calculation and the pipelined operation are elegantly combined to strike a balance between the complexity and the latency.Moreover,we employ only one successive cancellation(SC)decoder core without L×L crossbars,and reduce the number of inputs of the metric sorter from 2L to L+2.Finally,the FPGA implementations show that the hardware resource consumption is significantly reduced with negligible decoding performance loss.展开更多
文摘针对流水线型逐次逼近模数转换器(Pipelined SAR ADC)中残差放大器的核心运放功耗过高,从而严重限制ADC能效上限的问题,本文提出了一种新型的基于CMOS开关的自偏置全差分环形放大器(CMOS Self-biased Fully Differential Ring Amplifier,CSFRA),来替代传统运放。CSFRA通过引入CMOS开关自偏置和全差分结构,同时在非放大时序中关断电路,降低了残差放大器功耗。基于所提CSFRA,配合可降低开关功耗的检测和跳过切换方案,设计了一款12 Bit 10 MS/s的Pipelined SAR ADC。该电路基于MXIC L18B 180 nm CMOS工艺实现,实验结果表明,在10 MS/s的采样率下,该电路的SFDR和SNDR分别为75.3 dB和61.3 dB,功耗仅为944μW,其中CSFRA功耗仅为368μW。
基金supported by the Major National Science & Technology Program of China under Grant No.2012ZX03004004-002National High Technology Research and Development Program of China under Grant No. 2013AA014302
文摘A low-power 14-bit 150MS/s an- alog-to-digital converter （ADC） is present- ed for communication applications. Range scaling enables a maximal 2-Vp-p input with a single-stage opamp adopted. Opamp and capacitor sharing between the first multi- plying digital-to-analog converter （MDAC） and the second one reduces the total opamp power further. The dedicated sample-and- hold amplifier （SHA） is removed to lower the power and the noise. The blind calibration of linearity errors is proposed to improve the per- formance. The prototype ADC is fabricated in a 130rim CMOS process with a 1.3-V supply voltage. The SNDR of the ADC is 71.3 dB with a 2.4 MHz input and remains 68.5 dB for a 120 MHz input. It consumes 85 roW, which includes 57 mW for the ADC core, 11 mW for the low jitter clock receiver and 17 mW for the high-speed reference buffer.
基金supported by the National Natural Science Foundation of China(No.61106027)the 333 Talent Project of Jiangsu Province, China(No.BRA2011115)
文摘A low power 10-bit 125-MSPS charge-domain(CD) pipelined analog-to-digital converter(ADC) based on MOS bucket-brigade devices(BBDs) is presented.A PVT insensitive boosted charge transfer(BCT) that is able to reject the charge error induced by PVT variations is proposed.With the proposed BCT,the common mode charge control circuit can be eliminated in the CD pipelined ADC and the system complexity is reduced remarkably.The prototype ADC based on the proposed BCT is realized in a 0.18μm CMOS process,with power consumption of only 27 mW at 1.8-V supply and active die area of 1.04 mm^2.The prototype ADC achieves a spurious free dynamic range(SFDR) of 67.7 dB,a signal-to-noise ratio(SNDR) of 57.3 dB,and an effective number of bits(ENOB) of 9.0 for a 3.79 MHz input at full sampling rate.The measured differential nonlinearity(DNL) and integral nonlinearity (INL) are +0.5/-0.3 LSB and +0.7/-0.55 LSB,respectively.
基金supported by National Natural Science Foundation of China under grant No.61704161Key Project of Natural Science of Anhui Provincial Department of Education under grant No.KJ2017A396
文摘A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the precision of CD pipelined ADCs is restricted by the variation in input CM charge, which can compensate for CM charge errors caused by a variation in CM charge input in real time. Based on the feed-forward CM charge control circuit, a 12-bit 250-MS/s CD pipelined ADC is designed and realized using a 1P6M 0.18-μm CMOS process. The ADC achieved a Spurious Free Dynamic Range （SFDR） of 78.1 dB and a Signal-to-Noise-and-Distortion Ratio （SNDR） of 64.6 dB for a 20.1-MHz input; a SFDR of 74.9 dB and SNDR of 62.0 dB were achieved for a 239.9-MHz input at full sampling rate. The variation in signal-to-noise ratio was less than 3 dB over a 0-1.2 V input CM voltage range. The power consumption of the prototype ADC is only 85 mW at 1.8 V supply, and it occupies an active die area of 2.24 mm^2.
基金supported by the Micro/Nanoelectronics Science and Technology Innovation Platform of Fudan University of China
文摘A CMOS fluorescent detector system for biological experiment is presented. This system integrates a CMOS compatible photodiode, a capacitive trans-impedance amplifier （CTIA）, and a 12 bit pipelined analog-to- digital converter （ADC）, and is implemented in a 0.18μm standard CMOS process. Some special techniques, such as a ＂contact imaging＂ detecting method, pseudo-differential architecture, dummy photodiodes, and a T-type reset switch, are adopted to achieve low-level sensing application. Experiment results show that the Nwell/Psub photodiode with CTIA pixel achieves a sensitivity of 0.1 A/W at 515 nm and a dark current of 300 fA with 300 mV reverse biased voltage. The maximum differential and integral nonlinearity of the designed ADC are 0.8 LSB and 3 LSB, respectively. With an integrating time of 50 ms, this system is sensitive to the fluorescence emitted by the fluorescein solution with concentration as low as 20 ng/mL and can generate 7 fA photocurrent. This chip occupies 3 mm^2 and consumes 37 mW.
文摘This paper presents a 12-bit 100 MS/s CMOS pipelined analog-to-digital converter （ADC） with digital background calibration. A large magnitude calibration signal is injected into the multiplying digital-to-analog converter （MDAC） while the architecture of the MDAC remains unchanged. When sampled at 100 MS/s, it takes only 2.8 s to calibrate the 12-bit prototype ADC and achieves a peak spurious-free dynamic range of 85 dB and a peak signal-to-noise plus distortion ratio of 66 dB with 2 MHz input. Integral nonlinearity is improved from 1.9 to 0.6 least significant bits after calibration. The chip is fabricated in a 0.18μm CMOS process, occupies an active area of 2.3 × 1.6 mm^2, and consumes 205 mW at 1.8 V.
基金supported in part by the National Key R&D Program of China(No.2019YFB1803400)。
文摘For polar codes,the performance of successive cancellation list(SCL)decoding is capable of approaching that of maximum likelihood decoding.However,the existing hardware architectures for the SCL decoding suffer from high hardware complexity due to calculating L decoding paths simultaneously,which are unfriendly to the devices with limited logical resources,such as field programmable gate arrays(FPGAs).In this paper,we propose a list-serial pipelined hardware architecture with low complexity for the SCL decoding,where the serial calculation and the pipelined operation are elegantly combined to strike a balance between the complexity and the latency.Moreover,we employ only one successive cancellation(SC)decoder core without L×L crossbars,and reduce the number of inputs of the metric sorter from 2L to L+2.Finally,the FPGA implementations show that the hardware resource consumption is significantly reduced with negligible decoding performance loss.
