The Box–Behnken design and desirability approach were used to investigate and optimize the process parameters for aluminum reduction cells related to alumina dissolution. The bath temperature, alumina content, curren...The Box–Behnken design and desirability approach were used to investigate and optimize the process parameters for aluminum reduction cells related to alumina dissolution. The bath temperature, alumina content, current and alumina temperature were chosen as the design parameters. The content of cumulative dissolved alumina(CCDA) and the relative deviation from the target content(RDTC) were adopted as the responses. The interactive influence results show that increasing the bath temperature and alumina temperature, as well as decreasing the alumina content, can increase CCDA. Increasing the bath temperature and lowering the current are beneficial for obtaining a more uniform alumina distribution. The optimal operating parameters were determined to be as follows: bath temperature of 958.8 ℃, alumina content of 2.679 wt.%, current of 300 kA and alumina temperature of 200 ℃.展开更多
In this study,2~5 （five factors at two-level factorial design） design of experiment was applied to investigate a set of optimal machining parameters to achieve a minimum surface roughness value for Abies nordmannian...In this study,2~5 （five factors at two-level factorial design） design of experiment was applied to investigate a set of optimal machining parameters to achieve a minimum surface roughness value for Abies nordmanniana.Wood specimens were prepared using different values of spindle speed,feed rate,depth of cut,tool radius,and cutting directions.Average surface roughness （R_z） values were applied using a stylus.The objectives were to：（1）obtain the effective variables of wood surface roughness;（2） analyze which of these factors had an impact on variability in the CNC machining process;（3） evaluate the optimal cutting values within the range of different cutting levels of machining parameters.The results indicate that the design of experiment（DOE） based on the desirability function approach determined the optimal machining parameters successfully,leading to minimum R_a compared to the observed value.Minimum surface roughness values of tangential and radial cutting directions were 3.58 and 3.21 μm,respectively.展开更多
A methodology for the selection of the optimal land uses of the reclamation of mined areas is proposed. It takes into consideration several multi-nature criteria and constraints, including spatial constrains related t...A methodology for the selection of the optimal land uses of the reclamation of mined areas is proposed. It takes into consideration several multi-nature criteria and constraints, including spatial constrains related to the permissible land uses in certain parts of the mined area. The methodology combines desirability functions and evolution searching algorithms for selection of the optimal reclamation scheme. Its application for the reclamation planning of the Amynteon lignite surface mine in Greece indicated that it handles effectively spatial and non-spatial constraints and incorporates easily the decision-makers preferences regarding the reclamation strategy in the optimization procedure.展开更多
The sample preparation of samples conlaining bovine serum albumin（BSA）,e.g..as used in transdermal Franz diffusion cell（FDC） solutions,was evaluated using an analytical qualily-by-design（QbD）approach.Traditional...The sample preparation of samples conlaining bovine serum albumin（BSA）,e.g..as used in transdermal Franz diffusion cell（FDC） solutions,was evaluated using an analytical qualily-by-design（QbD）approach.Traditional precipitation of BSA by adding an equal volume of organic solvent,often successfully used with conventional HPLC-PDA,was found insufficiently robust when novel fused-core HPLC and/or UPLC-MS methods were used.In this study,three factors（acetonitrile（%）.formic acid（%） and boiling time（min）） were included in the experimental design to determine an optimal and more suitable sample treatment of BSAcontaining FDC solutions.Using a QbD and Derringer desirability（D） approach,combining BSA loss,dilution factor and variability,we constructed an optimal working space with the edge of failure defined as D〈0.9.The design space is modelled and is confirmed to have an ACN range of 83 ± 3% and FA content of 1 ±0.25%.展开更多
Plant derived natural fibers have been widely investigated as alternatives to synthetic fibers in reinforcing polymers.Researchers over the years have explored many plant fibers using different extraction processes to...Plant derived natural fibers have been widely investigated as alternatives to synthetic fibers in reinforcing polymers.Researchers over the years have explored many plant fibers using different extraction processes to study their physical,chemical,and mechanical properties.In this context,the present study relates to the extraction,characterization,and optimization of Typha angustata L.stem fibers.For this purpose,desirability functions and response surface methodology were applied to simultaneously optimize the diameter(D),linear density(LD);yield(Y),lignin fraction(L),and tenacity(T)of Typha stem fibers.Typha stems have been subjected to both alkali(NaOH)and enzymatic(pectinex ultra-SPL)treatments.Three levels of process variables including enzyme concentration(10,15,and 20 ml/L)and treatment duration(10,15,and 20 days)were used to design the experiments according to the factorial design.Experimental results were examined by analysis of variance and fitted to second order polynomial model using multiple regression analysis.The Derringer’s desirability function released that the values of process variables generating optimized diameter,linear density,yield,lignin ratio and tenacity are 20 ml/L and 20 days for concentration of pectinex ultra-SPL enzyme and treatment duration,respectively.Confirmation was performed and high degree of correlation was found between the experimental and statistical values.Moreover,the morphological structure has been investigated by the scanning electron microscope,showing a crenelated structure of ultimate fiber bundles of cellulose composing the Typha fiber.Compared to Typha stem non-treated fibers(TSNTF),Typha stem combined treated fibers(TSCTF),brings to improve mechanical properties.This change in mechanical properties is affected by modifying the fiber structure showing alpha cellulose of(66.86%)and lignin ratio of(10.83%)with a crystallinity index of(58.47%).展开更多
Lipopeptides are currently re-emerging as an interesting subgroup in the peptide research field, having historical applications as antibacterial and antifungal agents and new potential applications as antiviral, antit...Lipopeptides are currently re-emerging as an interesting subgroup in the peptide research field, having historical applications as antibacterial and antifungal agents and new potential applications as antiviral, antitumor, immune-modulating and cell-penetrating compounds. However, due to their specific structure, chromatographic analysis often requires special buffer systems or the use of trifluoroacetic acid, limiting mass spectrometry detection. Therefore, we used a traditional aqueous/acetonitrile based gradient system, containing 0.1% （m/v） formic acid, to separate four pharmaceutically relevant lipopeptides （polymyxin B1, caspofungin, daptomycin and gramicidin A1）, which were selected based upon hierarchical cluster analysis （HCA） and principal component analysis （PCA）.In total, the performance of four different C18 columns, including one UPLC column, were evaluated using two parallel approaches. First, a Derringer desirability function was used, whereby six single and multiple chromatographic response values were rescaled into one overall D-value per column. Using this approach, the YMC Pack Pro C18 column was ranked as the best column for general MS-compatible lipopeptide separation. Secondly, the kinetic plot approach was used to compare the different columns at different flow rate ranges. As the optimal kinetic column performance is obtained at its maximal pressure, the length elongation factor λ（Pmax/Pexp） was used to transform the obtained experimental data （retention times and peak capacities） and construct kinetic performance limit （KPL） curves, allowing a direct visual and unbiased comparison of the selected columns, whereby the YMC Triart C18 UPLC and ACE C18 columns performed as best. Finally, differences in column performance and the （dis）advantages of both approaches are discussed.展开更多
基金Project(2010AA065201)supported by the High Technology Research and Development Program of ChinaProject(2018zzts157)supported by the Fundamental Research Funds for the Central Universities of Central South University,China。
文摘The Box–Behnken design and desirability approach were used to investigate and optimize the process parameters for aluminum reduction cells related to alumina dissolution. The bath temperature, alumina content, current and alumina temperature were chosen as the design parameters. The content of cumulative dissolved alumina(CCDA) and the relative deviation from the target content(RDTC) were adopted as the responses. The interactive influence results show that increasing the bath temperature and alumina temperature, as well as decreasing the alumina content, can increase CCDA. Increasing the bath temperature and lowering the current are beneficial for obtaining a more uniform alumina distribution. The optimal operating parameters were determined to be as follows: bath temperature of 958.8 ℃, alumina content of 2.679 wt.%, current of 300 kA and alumina temperature of 200 ℃.
基金performed in the laboratuary of Istanbul University,Faculty of Forestry where the authors are employed at present
文摘In this study,2~5 （five factors at two-level factorial design） design of experiment was applied to investigate a set of optimal machining parameters to achieve a minimum surface roughness value for Abies nordmanniana.Wood specimens were prepared using different values of spindle speed,feed rate,depth of cut,tool radius,and cutting directions.Average surface roughness （R_z） values were applied using a stylus.The objectives were to：（1）obtain the effective variables of wood surface roughness;（2） analyze which of these factors had an impact on variability in the CNC machining process;（3） evaluate the optimal cutting values within the range of different cutting levels of machining parameters.The results indicate that the design of experiment（DOE） based on the desirability function approach determined the optimal machining parameters successfully,leading to minimum R_a compared to the observed value.Minimum surface roughness values of tangential and radial cutting directions were 3.58 and 3.21 μm,respectively.
文摘A methodology for the selection of the optimal land uses of the reclamation of mined areas is proposed. It takes into consideration several multi-nature criteria and constraints, including spatial constrains related to the permissible land uses in certain parts of the mined area. The methodology combines desirability functions and evolution searching algorithms for selection of the optimal reclamation scheme. Its application for the reclamation planning of the Amynteon lignite surface mine in Greece indicated that it handles effectively spatial and non-spatial constraints and incorporates easily the decision-makers preferences regarding the reclamation strategy in the optimization procedure.
基金the Special Research Fund of Ghent University(BOF 01D23812 to Lien Taevernier and BOF O1J22510 to Evelien Wynendaele and Professor Bart De Spiegeleer)the Institute for the Promotion of Innovation through Science and Technology in Flanders(IWT 101529 to Matthias D'Hondt)for their financial funding
文摘The sample preparation of samples conlaining bovine serum albumin（BSA）,e.g..as used in transdermal Franz diffusion cell（FDC） solutions,was evaluated using an analytical qualily-by-design（QbD）approach.Traditional precipitation of BSA by adding an equal volume of organic solvent,often successfully used with conventional HPLC-PDA,was found insufficiently robust when novel fused-core HPLC and/or UPLC-MS methods were used.In this study,three factors（acetonitrile（%）.formic acid（%） and boiling time（min）） were included in the experimental design to determine an optimal and more suitable sample treatment of BSAcontaining FDC solutions.Using a QbD and Derringer desirability（D） approach,combining BSA loss,dilution factor and variability,we constructed an optimal working space with the edge of failure defined as D〈0.9.The design space is modelled and is confirmed to have an ACN range of 83 ± 3% and FA content of 1 ±0.25%.
文摘Plant derived natural fibers have been widely investigated as alternatives to synthetic fibers in reinforcing polymers.Researchers over the years have explored many plant fibers using different extraction processes to study their physical,chemical,and mechanical properties.In this context,the present study relates to the extraction,characterization,and optimization of Typha angustata L.stem fibers.For this purpose,desirability functions and response surface methodology were applied to simultaneously optimize the diameter(D),linear density(LD);yield(Y),lignin fraction(L),and tenacity(T)of Typha stem fibers.Typha stems have been subjected to both alkali(NaOH)and enzymatic(pectinex ultra-SPL)treatments.Three levels of process variables including enzyme concentration(10,15,and 20 ml/L)and treatment duration(10,15,and 20 days)were used to design the experiments according to the factorial design.Experimental results were examined by analysis of variance and fitted to second order polynomial model using multiple regression analysis.The Derringer’s desirability function released that the values of process variables generating optimized diameter,linear density,yield,lignin ratio and tenacity are 20 ml/L and 20 days for concentration of pectinex ultra-SPL enzyme and treatment duration,respectively.Confirmation was performed and high degree of correlation was found between the experimental and statistical values.Moreover,the morphological structure has been investigated by the scanning electron microscope,showing a crenelated structure of ultimate fiber bundles of cellulose composing the Typha fiber.Compared to Typha stem non-treated fibers(TSNTF),Typha stem combined treated fibers(TSCTF),brings to improve mechanical properties.This change in mechanical properties is affected by modifying the fiber structure showing alpha cellulose of(66.86%)and lignin ratio of(10.83%)with a crystallinity index of(58.47%).
基金funded by PhD grants of ‘Institute for the Promotion of Innovation through Science and Technology in Flanders (IWT-Vlaanderen)’ (Nos. 101529 (MD) and 121512 (BG))The Special Research Fund (BOF) of Ghent University (01J22510 (EW) and 01D38811 (SS))
文摘Lipopeptides are currently re-emerging as an interesting subgroup in the peptide research field, having historical applications as antibacterial and antifungal agents and new potential applications as antiviral, antitumor, immune-modulating and cell-penetrating compounds. However, due to their specific structure, chromatographic analysis often requires special buffer systems or the use of trifluoroacetic acid, limiting mass spectrometry detection. Therefore, we used a traditional aqueous/acetonitrile based gradient system, containing 0.1% （m/v） formic acid, to separate four pharmaceutically relevant lipopeptides （polymyxin B1, caspofungin, daptomycin and gramicidin A1）, which were selected based upon hierarchical cluster analysis （HCA） and principal component analysis （PCA）.In total, the performance of four different C18 columns, including one UPLC column, were evaluated using two parallel approaches. First, a Derringer desirability function was used, whereby six single and multiple chromatographic response values were rescaled into one overall D-value per column. Using this approach, the YMC Pack Pro C18 column was ranked as the best column for general MS-compatible lipopeptide separation. Secondly, the kinetic plot approach was used to compare the different columns at different flow rate ranges. As the optimal kinetic column performance is obtained at its maximal pressure, the length elongation factor λ（Pmax/Pexp） was used to transform the obtained experimental data （retention times and peak capacities） and construct kinetic performance limit （KPL） curves, allowing a direct visual and unbiased comparison of the selected columns, whereby the YMC Triart C18 UPLC and ACE C18 columns performed as best. Finally, differences in column performance and the （dis）advantages of both approaches are discussed.
