An orthogonal experiment scheme was designed to investigate the effects of the Cu content,compaction pressure,and sintering temperature on the microstructures and mechanical and thermal properties of(30−50)wt.%Cu/Inva...An orthogonal experiment scheme was designed to investigate the effects of the Cu content,compaction pressure,and sintering temperature on the microstructures and mechanical and thermal properties of(30−50)wt.%Cu/Invar bi-metal matrix composites fabricated via spark plasma sintering(SPS).The results indicated that as the Cu content increased from 30 to 50 wt.%,a continuous Cu network gradually appeared,and the density,thermal conductivity(TC)and coefficient of thermal expansion of the composites noticeably increased,but the tensile strength decreased.The increase in the sintering temperature promoted the Cu/Invar interface diffusion,leading to a reduction in the TC but an enhancement in the tensile strength of the composites.The compaction pressure comprehensively affected the thermal properties of the composites.The 50wt.%Cu/Invar composite sintered at 700℃ and 60 MPa had the highest TC(90.7 W/(m·K)),which was significantly higher than the TCs obtained for most of the previously reported Cu/Invar composites.展开更多
Fe^(2+)dissolution method and manual method were used to remove the anode slime and their effects on properties of cast Pb−0.6wt.%Ag anode and zinc electrowinning were compared.The results reveal that the Fe^(2+)disso...Fe^(2+)dissolution method and manual method were used to remove the anode slime and their effects on properties of cast Pb−0.6wt.%Ag anode and zinc electrowinning were compared.The results reveal that the Fe^(2+)dissolution method can avoid mechanical damage to the oxide film layer on the anode surface,which cannot be achieved by traditional manual method.This can lower the anode corrosion rate by 57.14%,thus reducing Pb contamination in electrolyte and zinc products.Meanwhile,compared with manual method,Fe^(2+)dissolution method can significantly improve the electrocatalytic activity of the anode and lower the initial power consumption of zinc electrowinning to 2720 kW·h/t after removing anode slime.展开更多
30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the co...30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the composites were investigated.The results indicated that interfacial reactions were inhibited during SPS because no Al4C3 was detected.Moreover,the agglomeration of the GNFs increased,and the distribution orientation of the GNFs decreased with increasing the GNF content.The relative density,bending strength,and coefficient of thermal expansion(CTE)of the composites decreased,while the thermal conductivity(TC)in the X−Y direction increased.As the sintering pressure increased,the GNFs deagglomerated and were distributed preferentially in the X−Y direction,which increased the relative density,bending strength and TC,and decreased the CTE of the composites.The 50wt.%GNFs/6061Al matrix composite sintered at 610℃ under 55 MPa demonstrated the best performance,i.e.,bending strength of 72 MPa,TC and CTE(RT−100℃)of 254 W/(m·K)and 8.5×10^(−6)K^(−1)in the X−Y direction,and 55 W/(m·K)and 9.7×10^(−6)K^(−1)in the Z direction,respectively.展开更多
Dense B;C material was fabricated using spark plasma sintering(SPS), and the densification mechanisms and grain growth kinetics were revealed. The density, hardness, transverse flexure strength and toughness of sample...Dense B;C material was fabricated using spark plasma sintering(SPS), and the densification mechanisms and grain growth kinetics were revealed. The density, hardness, transverse flexure strength and toughness of samples were investigated and the model predictions were confirmed by SEM and TEM experimental observations. Results show that SPSed B;C exhibits two sintering periods: a densification period(1800-2000 °C) and a grain growth period(2100-2200 °C). Based on steady-state creep model, densification proceeds by grain boundary sliding and then dislocation-climb-controlled mechanism. Grain growth mechanism is controlled by grain boundary diffusion at 2100 °C,and then governed by volume or liquid-phase diffusion at 2200 °C.展开更多
基金the International Science&Technology Cooperation Program of China(No.2014DFA50860).
文摘An orthogonal experiment scheme was designed to investigate the effects of the Cu content,compaction pressure,and sintering temperature on the microstructures and mechanical and thermal properties of(30−50)wt.%Cu/Invar bi-metal matrix composites fabricated via spark plasma sintering(SPS).The results indicated that as the Cu content increased from 30 to 50 wt.%,a continuous Cu network gradually appeared,and the density,thermal conductivity(TC)and coefficient of thermal expansion of the composites noticeably increased,but the tensile strength decreased.The increase in the sintering temperature promoted the Cu/Invar interface diffusion,leading to a reduction in the TC but an enhancement in the tensile strength of the composites.The compaction pressure comprehensively affected the thermal properties of the composites.The 50wt.%Cu/Invar composite sintered at 700℃ and 60 MPa had the highest TC(90.7 W/(m·K)),which was significantly higher than the TCs obtained for most of the previously reported Cu/Invar composites.
基金supported by Zhejiang Libo Industrial Co.,Ltd.,Shaoxing,China。
文摘Fe^(2+)dissolution method and manual method were used to remove the anode slime and their effects on properties of cast Pb−0.6wt.%Ag anode and zinc electrowinning were compared.The results reveal that the Fe^(2+)dissolution method can avoid mechanical damage to the oxide film layer on the anode surface,which cannot be achieved by traditional manual method.This can lower the anode corrosion rate by 57.14%,thus reducing Pb contamination in electrolyte and zinc products.Meanwhile,compared with manual method,Fe^(2+)dissolution method can significantly improve the electrocatalytic activity of the anode and lower the initial power consumption of zinc electrowinning to 2720 kW·h/t after removing anode slime.
基金financial support from the International Science&Technology Cooperation Program of China(No.2014DFA50860)。
文摘30-50 wt.%graphite nanoflakes(GNFs)/6061Al matrix composites were fabricated via spark plasma sintering(SPS)at 610℃.The effects of the sintering pressure and GNF content on the microstructure and properties of the composites were investigated.The results indicated that interfacial reactions were inhibited during SPS because no Al4C3 was detected.Moreover,the agglomeration of the GNFs increased,and the distribution orientation of the GNFs decreased with increasing the GNF content.The relative density,bending strength,and coefficient of thermal expansion(CTE)of the composites decreased,while the thermal conductivity(TC)in the X−Y direction increased.As the sintering pressure increased,the GNFs deagglomerated and were distributed preferentially in the X−Y direction,which increased the relative density,bending strength and TC,and decreased the CTE of the composites.The 50wt.%GNFs/6061Al matrix composite sintered at 610℃ under 55 MPa demonstrated the best performance,i.e.,bending strength of 72 MPa,TC and CTE(RT−100℃)of 254 W/(m·K)and 8.5×10^(−6)K^(−1)in the X−Y direction,and 55 W/(m·K)and 9.7×10^(−6)K^(−1)in the Z direction,respectively.
基金the financial supports from the National Natural Science Foundation of China (No. 51874369)Hunan Provincial Natural Science Foundation, China (No. 2021JJ30856)+1 种基金the China Scholarship Council for financial supports (No. CSC201906370123)the Fundamental Research Funds for the Central Universities of Central South University, China (No. 2020zzts084)。
文摘Dense B;C material was fabricated using spark plasma sintering(SPS), and the densification mechanisms and grain growth kinetics were revealed. The density, hardness, transverse flexure strength and toughness of samples were investigated and the model predictions were confirmed by SEM and TEM experimental observations. Results show that SPSed B;C exhibits two sintering periods: a densification period(1800-2000 °C) and a grain growth period(2100-2200 °C). Based on steady-state creep model, densification proceeds by grain boundary sliding and then dislocation-climb-controlled mechanism. Grain growth mechanism is controlled by grain boundary diffusion at 2100 °C,and then governed by volume or liquid-phase diffusion at 2200 °C.
