摘要
背景:3D打印个体化截骨导板辅助开放楔形胫骨高位截骨治疗膝骨关节炎具有手术时间短、透视次数少、矫正精准度高等优点。但之前报道的截骨导板对周围软组织破坏严重、锁定钢板位置不当等问题依旧明显。目的:探究3D打印个体化截骨导板结合定制钢板辅助开放楔形胫骨高位截骨治疗膝骨关节炎的临床疗效。方法:收集20例确诊为膝骨关节炎的患者,按手术方法分为3D组和常规组,每组10例。3D组采用3D打印个体化截骨导板结合定制钢板辅助开放楔形胫骨高位截骨手术,常规组进行常规开放楔形胫骨高位截骨手术。分析比较两组患者手术时间、透视次数、切口长度,术前和术后髋膝踝角、胫骨近端内侧角、胫骨后倾角以及计划矫正角度与实际矫正角度的差值,术前和术后1,3,6个月膝关节活动度及Lysholm评分,另外记录并发症发生情况。结果与结论:①3D组患者的手术时间、透视次数少于常规组,差异有显著性意义(P<0.001);②两组患者的术后髋膝踝角、胫骨近端内侧角均较术前增大,差异有显著性意义(P<0.001),而胫骨后倾角无明显改变;3D组术后髋膝踝角、胫骨近端内侧角及胫骨后倾角与术前计划值分别相差(-0.22±0.72)°、(-0.20±0.73)°和(0.23±0.37)°,但差异均无显著性意义;3D组计划矫正度数与实际矫正度数的差值较常规组小,差异有显著性意义(P<0.05);③两组患者术后膝关节活动度及Lysholm评分均逐步升高(P<0.001);3D组术后1,3个月的膝关节活动度及术后1个月的Lysholm评分优于常规组,差异有显著性意义(P<0.05);两组患者术后3个月的Lysholm评分、术后6个月的膝关节活动度及Lysholm评分差异无显著性意义(P>0.05);④两组患者均无并发症发生;⑤上述结果说明3D打印个体化截骨导板结合定制钢板辅助和常规方法均有良好的临床疗效,但前者的手术时间更短,透视次数更少,术后膝关�
BACKGROUND:The use of 3D-printed patient-specific instruments in opening wedge high tibial osteotomy has advantages such as shorter operative time,fewer fluoroscopic exposures,and higher correction accuracy.However,previous studies have reported issues such as significant damage to surrounding soft tissues and improper fixation of the plates.OBJECTIVE:To investigate the clinical efficacy of using 3D-printed patient-specific instruments combined with customized locking plate in opening wedge high tibial osteotomy for the treatment of knee osteoarthritis.METHODS:A total of 20 patients diagnosed with knee osteoarthritis were divided into the 3D group(n=10)and the conventional group(n=10)according to surgical methods.The 3D group underwent opening wedge high tibial osteotomy using 3D-printed patient-specific instruments combined with customized locking plate,while the conventional group underwent opening wedge high tibial osteotomy using conventional methods.The operative time,fluoroscopic exposures,incision length,pre-and postoperative hip-knee-ankle angle,medial proximal tibial angle,posterior tibial slope,the difference between the planned and actual correction angle,preoperative and 1,3,6 months postoperative knee range of motion and Lysholm score,and incidence of complications were analyzed and compared between the two groups.RESULTS AND CONCLUSION:(1)The operative time and fluoroscopic exposures were significantly shorter in the 3D group compared to the conventional group,with a statistically significant difference(P<0.001).(2)Both groups showed a significant improvement in postoperative hip-knee-ankle angle and medial proximal tibial angle compared to preoperative values,with a statistically significant difference(P<0.001),while there was no significant change in posterior tibial slope.In the 3D group,the postoperative hip-knee-ankle angle,medial proximal tibial angle,and posterior tibial slope differed from their respective preoperative planned values by(-0.22±0.72)°, (-0.20±0.73)°, and (0.23±0.37)°, bu
作者
马驰
王宁
陈拥
魏志晗
刘逢纪
朴成哲
Ma Chi;Wang Ning;Chen Yong;Wei Zhihan;Liu Fengji;Piao Chengzhe(Central Hospital Affiliated to Shenyang Medical College,Shenyang 110075,Liaoning Province,China)
出处
《中国组织工程研究》
CAS
北大核心
2025年第9期1863-1869,共7页
Chinese Journal of Tissue Engineering Research
基金
沈阳医学院硕士研究生科技创新基金项目(Y20220526),项目负责人:马驰
沈阳医学院科技基金项目(20191009),项目负责人:王宁
沈阳市中青年科技创新人才支持计划项目(RC220422),项目负责人:陈拥。
关键词
3D打印
个体化截骨导板
定制钢板
开放楔形胫骨高位截骨
膝骨关节炎
3D printing
patient-specific instruments
customized locking plate
opening wedge high tibial osteotomy
knee osteoarthritis
