期刊文献+

应力比对A7N01铝合金焊接接头裂纹近门槛值区拐点的影响

The inflection of stress ratio on the threshold region of crack for welded joint of A7N01 aluminum alloy
下载PDF
导出
摘要 以A7N01铝合金焊接接头为研究对象,借助有限元法及有限元软件先进行A7N01铝合金板对接焊模拟,得到接头处残余应力分布情况,再对接头裂纹进行扩展模拟,最后应用最小二乘法对提取的仿真数据进行处理,重点分析了应力比对疲劳裂纹近门槛值区拐点的影响。结果表明:在接头裂纹扩展速率曲线的近门槛值区存在一个拐点,且应力比对其有影响。拐点对应的应力强度因子幅值ΔK t随应力比R的增大而减小,且当R>0.5时,ΔK t变化不大。拐点前后拟合直线斜率k随应力比R的变化为:在L 1区(低速扩展区),拟合直线斜率k 1随应力比R的变化更为明显,且随应力比R的增大而减小;在L 2区(Paris的延续),拟合直线斜率k 2随应力比R变化不大。 Taking A7N01 aluminum alloy welded joints as object,it simulates the fatigue cracks in finite element method,analyzes the effect of stress ratio on fatigue cracks in the near threshold region inflection point.And then it simulates the crack propagation of joint.Using the least square method,it discusses the extracted simulation data.The results show that there is an inflection point near threshold region of A7N01 aluminum alloy welded joint fatigue crack growth rate curve,and the stress ratio has an influence on it.The amplitude of stress intensity factorΔK t corresponding to inflection point decreases with the increase of stress ratio R,but when R>0.5,the change of the amplitude of stress intensity factor is not big,and the relation betweenΔK t and R is obtained at the same time.The change of the line slope k is variational with the stress ratio R before and after the inflection point:in the zone L 1,the change of the line slope k 1 with the stress ratio R is more obvious,and decreases with the increase of the stress ratio,while in the zone L 2,the k 2 varies little with the stress ratio R.
作者 李有堂 王亚东 Li Youtang;Wang Yadong(Laboratory of Digital Manufacturing Technology and Application Ministry of Education,Lanzhou University of Technology,Gansu Lanzhou,730050,China;College of Mechanic-Electronic Engineering,Lanzhou University of Technology,Gansu Lanzhou,730050,China)
出处 《机械设计与制造工程》 2019年第7期108-113,共6页 Machine Design and Manufacturing Engineering
关键词 A7N01铝合金 焊接接头裂纹 近门槛值区 拐点 应力比 A7N01 aluminum alloy welded joint crack near threshold region inflection point stress ratio
  • 相关文献

参考文献6

二级参考文献51

  • 1黄小平,韩芸,崔维成,万正权,卞如冈.变幅载荷作用下焊接接头疲劳寿命预测方法[J].船舶力学,2005,9(1):89-97. 被引量:15
  • 2胡绪腾,宋迎东.总应变-应变能区分法[J].机械工程学报,2007,43(2):219-224. 被引量:6
  • 3吴世处.十字形铝合金焊接材料裂纹试验《金属的可焊性试验》[M].上海:上海科学技术文献出版社,1983. 被引量:1
  • 4BS EN 910-1996,金属材料焊缝破坏试验-弯曲试验[S]. 被引量:1
  • 5PARIS P C, ERDOGAN E A critical analysis of crack propagation laws [J]. J. Basic Engng., 1963, 85: 528-534. 被引量:1
  • 6SURESH S. Fatigue of materials [M]. Cambridge: Cambridge University Press, 1991. 被引量:1
  • 7ELBER W. The significance of fatigue crack closure [J]. ASTM STP 486, American Society for Testing and Materials, 1971: 230-242. 被引量:1
  • 8STOYCHEV S, KUJAWSKI D. Methods for crack opening load and crack tip shielding determination: A review [J]. Fatigue Fract. Engug Mater. Struct., 2003, 26. 1053-1067. 被引量:1
  • 9NISITANI H, CHEN D H. A consideration on the unloading elastic compliance method [J]. Trans. Jpn. Soc. Mech. Eng., 1985, 51: 1436-1441. 被引量:1
  • 10KUJAWSKI D, STOYCHEV S. Parametric study on the variability of opening load determination [J]. Int. J. Fatigue, 2003, 25: 1181-1187. 被引量:1

共引文献50

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部