期刊文献+

板级球栅阵列无铅焊点随机振动寿命分析 被引量:2

Lifetime Analysis of Lead-Free Ball Grid Array Solder Joints under Random Vibration
下载PDF
导出
摘要 进行了4组加速度的功率谱密度(PSD)条件下的焊点疲劳寿命试验,采用比例风险模型(PHM)分析加速度的PSD对焊点寿命的影响,并采用估计所得寿命期望(MTTF),结合Miner准则得到板极无铅焊点随机振动寿命损伤累积模型.结果表明:焊点疲劳寿命试验的结果与PHM估计所得焊点寿命的MTTF及其失效概率密度(PDF)吻合较好;当输入加速度的PSD幅值大于60 m2/s3时,焊点的MTTF值小于1 800 s,表明无铅焊点对随机振动载荷非常敏感. Four groups of random vibration tests of solder joints were conducted with different power spectral density(PSD) of in-put acceleration.Proportional hazards model(PHM) was used to evaluate the effect of PSD of in-put acceleration on the solder joints' life span.The mean-time-to-failure(MTTF) and the failure probability density function(PDF) estimated from the PHM agree well with the experimental data,and this validates the effectiveness of the PHM.By the curve of the MTTF s,it can be observed that the MTTF1 800 s when the amplitude of PSD was greater than 60 m2/s3,and this demonstrates that the lead-free solder joints are very sensitive to random vibration loading.Finally,the estimated lifetime of MTTF was integrated with the Miner's law for cumulative damage model of lead-free solder joints.
出处 《上海交通大学学报》 EI CAS CSCD 北大核心 2011年第9期1362-1367,1373,共7页 Journal of Shanghai Jiaotong University
基金 国家自然科学基金(10325209) 中国博士后基金(20090450699)资助项目
关键词 功率谱密度 比例风险模型 寿命期望值 Miner准则 power spectral density(PSD) proportional hazards model(PHM) mean-time-to-failure(MTTF) Miner's law
  • 引文网络
  • 相关文献

参考文献20

  • 1Institute for Clinical and Economic Review. Waste electronic and electrical equipment [M]. European: The European Union, 2000, 14. 被引量:1
  • 2JEIDA. Challenges and efforts toward commercialization of lead free solderroad map 2000 for commercialization of lead free solder [M]. Japan: Japan Electronic Industry Development Association, 2000. 被引量:1
  • 3Suhir E. Could compliant external leads reduce the strength of a surface mounted device? [C]// 38th Electronic Components and Technology Conference. CA: Los Angeles, 1988: 16. 被引量:1
  • 4Suhir E. Is the maximum acceleration an adequate criterion of the dynamic strength of a structural element in an electronic package? [J]. Components, Packaging, and Manufacturing Technology: Part A, 1997, 20 (7): 513517. 被引量:1
  • 5Pitarresi J M, Caletka D V, Caldwell R, et al. The “ smeared ” property technique for the FE vibration analysis of printed circuit cards [J]. J Electron Packag, 1991,113: 250257. 被引量:1
  • 6Pitarresi J M, Primavera A A. Comparison of modeling techniques for the vibration analysis of printed circuit cards [J]. ASME J Electron Packag, 1992, 114 (4): 378383. 被引量:1
  • 7Pitarresi J, Geng P, Yun L. Dynamic modeling and measurement of personal computer motherboards[C]// Electronic Components and Technology Conference. CA: San Diego, 2002: 597603. 被引量:1
  • 8Perkins A, Sitaraman S K. Analysis and prediction of vibrationinduced solder joint failure for a ceramic column grid array package[J]. Journal of Electronic Packaging, 2008, 130 (1): 011012.111. 被引量:1
  • 9Che F X, Pang John H L. Vibration reliability test and finite element analysis for flip chip solder joints[J]. Microelectronics Reliability, 2009, 49 (7): 754760. 被引量:1
  • 10Grieu M, Massiot G, Maire O, et al. Durability modeling of a BGA component under random vibration[C]// Proceedings of 9th Int Conf on Thermal, Mechanical and MultiPhysics Simulation and Experiments in MicroElectronics and MicroSystems. USA: IEEE, 2008: 18. 被引量:1

同被引文献8

引证文献2

二级引证文献4

;
使用帮助 返回顶部