期刊文献+

6063铝合金阶梯焊中温钎料腐蚀性能 被引量:3

Corrosion resistance of intermediate temperature filler metal for stepped welding to 6063 aluminum alloy
下载PDF
导出
摘要 采用正交试验法,通过改变Si,Cu,Ni以及混合稀土RE元素的配比,研究了含量的变化对Al-Si-Cu-Ni-RE钎料的自腐蚀电位、失重质量、腐蚀速率的影响,并通过扫描电镜观察分析了腐蚀前后钎料的内部显微组织.研究发现,钎料的自腐蚀电位与与失重质量相对应,随着腐蚀电位的负值增加,失重质量也不断增大.结果表明,对钎料腐蚀速率的影响依次为Ni元素的影响最大,其次为Si,Cu,RE元素.对钎料腐蚀前后的显微组织观察分析可知,由于基体相α(Al)属于面心立方固溶体,使得Al-Si-Cu-Ni-RE钎料的力学性能优良,但钎料中黑色的脆性θ(CuAl2)相的存在对钎焊接头的性能有不利影响,Cl-是诱发钎料点蚀的主要原因.腐蚀后的钎料局部区域出现了点蚀,腐蚀后的钎料有明显的网纹状晶间腐蚀. The effects of contents of Si,Cu,Ni and RE on the corrosion potential,weightlessness and corrosion rate of Al-Si-Cu-Ni-RE filler metal were studied by using orthogonal test,and the microstructure of the corroded filler metal was analyzed by means of SEM and EDS.It is indicated that the corrosion potential of the filler metal is relative to its weightlessness,which with the increase of the negative value of corrosion potential,the weightlessness increases continuously.Based on the corrosion rates,the results show that Ni has the most important influence on the melting points,and then do Si,Cu and RE.Through observed and analyzed the microstructure of filler metal,it is found that the matrix phase α(Al) with face-centered cubic solid solution makes the performance of joint better,but black brittle phase θ(Al2Cu) makes the performance of joint poorer;Cl-is the prime cause of induced pitting corrosion of the filler metal,which the pitting corrosion in filler metal and the obvious inter-granular corrosion are found in local area after corrosion.
出处 《焊接学报》 EI CAS CSCD 北大核心 2009年第10期29-32,共4页 Transactions of The China Welding Institution
基金 国防基础研究资助项目(B1120060474)
关键词 正交试验 腐蚀速率 点蚀 晶间腐蚀 orthogonal test corrosion rate pitting inter-granular corrosion
  • 相关文献

参考文献4

二级参考文献28

共引文献26

同被引文献27

  • 1韩德盛,李荻.温度对LY12铝合金海洋大气初期腐蚀行为的影响[J].材料保护,2007,40(6):7-8. 被引量:8
  • 2韩德盛,李荻.海洋大气湿度对LY12铝合金初期腐蚀的影响[J].中国腐蚀与防护学报,2007,27(3):134-136. 被引量:20
  • 3张启运 刘淑祺 等.氟铝酸钾高温铝钎剂的湿法合成及其在钎焊时的作用机理[J].焊接学报,1982,3(4):153-157. 被引量:9
  • 4S.Y. Chang,L.C. Tsao,T.Y. Li,T.H. Chuang.Joining 6061 aluminum alloy with Al–Si–Cu filler metals[J].Journal of Alloys and Compounds.2009(1) 被引量:1
  • 5L. C. Tsao,W. P. Weng,M. D. Cheng,C. W. Tsao,T. H. Chuang.Brazeability of a 3003 Aluminum alloy with Al-Si-Cu-based filler metals[J].Journal of Materials Engineering and Performance.2002(4) 被引量:1
  • 6T. H. Chuang,L. C. Tsao,T. C. Tsai,M. S. Yeh,C. S. Wu.Development of a low-melting-point filler metal for brazing aluminum alloys[J].Metallurgical and Materials Transactions A.2000(9) 被引量:1
  • 7S.Y. Chang,L.C. Tsao,T.Y. Li,T.H. Chuang.Joining 6061 aluminum alloy with Al–Si–Cu filler metals[J]. Journal of Alloys and Compounds . 2009 (1) 被引量:2
  • 8L. C. Tsao,W. P. Weng,M. D. Cheng,C. W. Tsao,T. H. Chuang.Brazeability of a 3003 Aluminum alloy with Al-Si-Cu-based filler metals[J]. Journal of Materials Engineering and Performance . 2002 (4) 被引量:1
  • 9T. H. Chuang,L. C. Tsao,T. C. Tsai,M. S. Yeh,C. S. Wu.Development of a low-melting-point filler metal for brazing aluminum alloys[J]. Metallurgical and Materials Transactions A . 2000 (9) 被引量:2
  • 10Humpston, G.,Sangha, S.P.S.,Jacobson, D.M.New filler metals and process for fluxless brazing of aluminium engineering alloys. Journal of Materials Science . 1995 被引量:2

引证文献3

二级引证文献9

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部