期刊文献+

单层钎焊立方氮化硼砂轮工作面磨粒包埋深度的确定 被引量:5

Determination of embedding depth of abrasive grains on working surface of single-layer brazed CBN grinding wheel
下载PDF
导出
摘要 以Ag-Cu-Ti合金为钎料在真空炉中实现了CBN磨粒与45钢基体的钎焊连接,运用红外光谱仪测试了钎焊磨粒内部的残余应力,分析了最大残余拉应力对磨粒强度的影响,据此优选了钎焊CBN砂轮工作面上磨粒的包埋深度。结果表明:当包埋深度不同时,尽管钎焊磨粒内部的残余应力分布差异较大,但最大残余拉应力始终位于磨粒与钎料顶层截面的边缘位置,并且最大残余拉应力与包埋深度不存在线性关系;为提高钎焊CBN磨粒强度和确保砂轮容屑空间,磨粒包埋深度应控制在其自身高度的30%~40%之间。 The joining of CBN abrasive grain and 0.45%C steel matrix was realized using Ag-Cu-Ti alloy as filler metal in the vacuum furnace. The residual stresses of the brazed CBN grains were measured by means of FTIR spectra. The influence of the maximum tensile stress on the grain strength was analyzed, and the embedding depth of grains on the working surface of the brazed single-layer grinding wheels was accordingly determined. The result shows that, though remarkable difference of stress distribution occurs in the brazed grains with different embedding depths, the maximum tensile stress always exists in the margin region of the section plane between CBN grain and filler top. Moreover, the maximum tensile stress is not influenced linearly by the embedding depth. In order to ensure the strength of the brazed grains and the enough space for holding chips, 30%-40% of the whole height of abrasive grain is the rational embedding depth for CBN grains.
出处 《中国有色金属学报》 EI CAS CSCD 北大核心 2007年第3期441-445,共5页 The Chinese Journal of Nonferrous Metals
基金 国家自然科学基金资助项目(50475040) 中国博士后科学基金资助项目(20060400282) 江苏省博士后科研计划资助项目(0602039B) 江苏省自然科学基金重点资助项目(BK2006723)
关键词 CBN磨粒 钎料层 单层钎焊砂轮 包埋深度 残余应力 CBN abrasive grain filler metal layer singer-layer brazed grinding wheel embedding depth residual stress
  • 相关文献

参考文献6

二级参考文献40

共引文献41

同被引文献26

  • 1丁文锋,徐九华,沈敏,傅玉灿,肖冰,苏宏华.活性元素Ti在CBN与钎料结合界面的特征[J].稀有金属材料与工程,2006,35(8):1215-1218. 被引量:9
  • 2杨志波,徐九华,傅玉灿,徐鸿钧.钢基体上镍基钎料激光钎焊金刚石磨粒的界面结构[J].机械工程材料,2007,31(5):17-19. 被引量:10
  • 3丁文锋,徐九华,傅玉灿,肖冰,苏宏华.基于残余应力分布优选钎焊CBN磨粒出露高度[J].中国机械工程,2007,18(10):1235-1238. 被引量:3
  • 4C. - M. Sung. Brazed diamond grid: a revolutionary design for diamond saws [ J ]. Diamond and Related Materials, 1999,8 ( 8-9 ) : 1540-1543. 被引量:1
  • 5宋振武,高航.螺旋槽砂轮磨削性能的试验研究[J].磨料磨具与磨削,1985(6):1-5. 被引量:1
  • 6黑征华.CBN砂轮高速磨削钛合金试验研究[D].南京:南京航空航天大学,2011. 被引量:1
  • 7Sung J C, Sung M. The Brazing of Diamond[J]. International Journal of Refractory Metals and Hard Materials,2009,27 (2) :382-393. 被引量:1
  • 8Chen S M, Lin S T. Brazing Diamond Grits onto a Steel Substrate Using Copper Alloys as The Filler Metals[ J]. Journal of Materials Engineering and Performance, 1996,5 (6) :761-766. 被引量:1
  • 9Li W C, Lin S T, Liang C. Interfacial Segregation of Ti In The Brazing of Diamond Grits onto a Steel Substrate Using a Ca-Sn-Ti Brazing Alloy [J]. Metallurgical and Materials transactions A,2002,33(7) :2163-2172. 被引量:1
  • 10Chattopadhyay A K, Chollet L, Hintermann H E. Experimental Investigation on Induction Brazing of Diamond With Ni-Cr Hardfacing Alloy under Argon Atmosphere[ J ]. Journal of Materials Science, 1991,26 (18) :5093-5010. 被引量:1

引证文献5

二级引证文献11

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部