期刊文献+

ABS注塑制品的模内蠕变试验研究 被引量:6

Test and Study on In-Mold Creep of ABS Injection Molded Part
下载PDF
导出
摘要 不同于传统的热残余应力分析,本文着眼于注塑制品的模内蠕变研究。通过测试ABS注塑薄板在不同工艺条件下的收缩变形,比较基于弹性理论的热收缩,进而得到了模内蠕变量。分析结果表明,模内蠕变对于降低制品最终的收缩变形起着重要的作用。在研究了各种工艺条件对制件模内蠕变的影响后,发现较低的模腔表面温度或较长的成型周期会导致蠕变增大,而制件在模内的蠕变(或应力松弛)主要发生在固化后的高温区。本文同时探讨了保压压力对蠕变的影响。高注塑保压压力通常会减小注塑件的收缩,但同时会减小制件模内蠕变。 Different from the traditional thermal residual stress research, the in-mold creep of injection molded part is studied. The shrinkages of the injection-molded thin plate of ABS material under different process conditions are tested, and then the inmold creep of the part is obtained by comparing the tested shrinkage with theoretical shrinkage based on elasticity. It is shown that the in-mold creep plays very important role in reducing final shrinkage of the part. The influence of the various process conditions to the creep is investigated. It is found that the lower mold wall temperature and the longer cycle time lead to more creep, and in-mold creep or residual stress relaxation of the part mainly happens in high temperature after the melt is solidified. The effect of packing pressure to the in-mold creep is also analyzed. The high injection packing pressure generally reduces the part shrinkage, but also reduces the in-mold creep at same time.
出处 《实验力学》 CSCD 北大核心 2006年第4期497-501,共5页 Journal of Experimental Mechanics
基金 国家自然科学基金重大项目(10590352)资助
关键词 蠕变 残余应力 ABS 注塑成型 收缩 creep residual stress injection molding shrinkage
  • 相关文献

参考文献11

  • 1Jansen K M B, Titomanlio G. Effect of pressure history on shrinkage and residual stresses-injection molding withconstrained shrinkage[J]. Polymer Engineering and Science, 1996, 36(15).2029-2040. 被引量:1
  • 2Zoetelief W F, Douven L F A, Housz A J. Residual thermal stresses in injection molded products[J]. PolymerEngineering and Science, 1996, 36(14) : 1886-1896. 被引量:1
  • 3Titomanlio G, Jansen K M B. In-mold shrinkage and stress prediction in injection molding[J]. Polymer Engineeringand Science, 1996,36 (15) :2041-2049. 被引量:1
  • 4Choi D S, Im Y T. Prediction of shrinkage and warpage in consideration of residual stress in integrated simulation of injection molding[J]. Composite Structures, 1999, 47 (1) :655-665. 被引量:1
  • 5Liu S J. New viscoelastic phase-transformation model to simulate the injection-molding residual stress[J]. Journalof Applied Polymer Science, 1996, 62(10):1537-1550. 被引量:1
  • 6Chen M, Yao D, Kim B. Eliminating flow induced birefringence and minimizing thermally induced residual stresses in injection molded parts[J]. Polymer-Plastics Technology and Engineering, 2001, 40(4):491-503. 被引量:1
  • 7Shen C Y, Li H M. Numerical simulation for effects of injection mold cooling on warpage and residual stresses[J].Polymer - Plastics Technology and Engineering, 2003, 42(5):971-982 . 被引量:1
  • 8陈静波,申长雨,刘春太,王利霞.聚合物注射成型流动残余应力的数值分析[J].力学学报,2005,37(3):272-279. 被引量:14
  • 9李海梅,顾元宪,申长雨.注塑件残余热应力的数值计算[J].化工学报,2000,51(3):308-312. 被引量:9
  • 10Chen X, Lam Y X, Li D Q. Analysis of thermal residual stress in plastic injection molding[J]. Journal of Materials Processing Technology, 2000, 101(1) :275-280. 被引量:1

二级参考文献10

  • 1Lee H H,Polym Eng Sci,1996年,36卷,21期,2634页 被引量:1
  • 2Yu JS, Wanger AH, Kalyon DM. Simulation of microstructure development in injection molding of engineering plastics. J Appl Polym Sci, 1992, 44(3): 477~489. 被引量:1
  • 3Baaijens FPT. Calculation of residual stresses in injection molded products. Rheol Acta, 1991, 30(3): 284~299. 被引量:1
  • 4Isayev AI. Orientation development in the injection molding of amorphous polymer. Polym Eng Sci, 1983, 23(5):271~284. 被引量:1
  • 5Dietz W, White J, Clark ES. Orientation development and relaxation in injection molding of amorphous. Polym Eng Sci, 1978, 18(4): 273~281. 被引量:1
  • 6Greener J, Pearson GH, Orientation residual stresses and birefringence in injection molding. J Rheol, 1983, 27(2):115~123. 被引量:1
  • 7Isayev AI, Hieber CA. Toward a viscoelastic modeling of the injection molding of polymers. Rheol Acta, 1980, 19(2):168~182. 被引量:1
  • 8Kim H, Park S J, Chung ST, et al. Numerical modeling of injection/compression molding for center-gated disk. Part 1: Injection molding with viscoelastic compressible fluid model. Polym Eng Sci, 1999, 39(10): 1930~1942. 被引量:1
  • 9Leonov AI, Lipkina EH, Paskin ED, et al. Theoretical and experimental investigation of shearing in elastic polymer liquids. Rheol Acta, 1976, 15(7/8): 411~426. 被引量:1
  • 10Isayev AI. Injection and Compression Molding Fundamentals. New York: Marcel Dekker, Inc, 1987. 被引量:1

共引文献19

同被引文献41

引证文献6

二级引证文献35

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部