Soil and water losses through erosion have been serious in the black soil region of Northeast China. Therefore, a sloping cultivated land in Songnen Plain was selected as a case study to： 1） determine the ^137Cs ref...Soil and water losses through erosion have been serious in the black soil region of Northeast China. Therefore, a sloping cultivated land in Songnen Plain was selected as a case study to： 1） determine the ^137Cs reference inventory in the study area; 2） calculate erosion and deposition rates of black soil on different slope locations; 3） conduct a sensitivity analysis of some model parameters; and 4） compare overall outputs using four different models. Three transects were set in the field with five slope locations for each transect, including summit, shoulder-slope, back-slope, foot-slope, and toe-slope. Field measurements and model simulation were used to estimate a bomb-derived ^137Cs reference inventory in the study area. Soil erosion and deposition rates were estimated using four ^137Cs models and percentage of ^137Cs loss/gain. The ^137Cs reference value in the study area was 2 232.8 Bq m^-2 with ^137Cs showing a clear topographic pattern, decreasing from the summit to shoulder-slope, then increasing again at the foot-slope and reaching a maximum at the toe-slope, Predicted soil redistribution rates for different slope locations varied. Among models, the Yang Model （YANG-M） overestimated erosion loss but underestimated deposition. However, the standard mass balance model （MBM1） gave predictions similar to a mass balance model incorporating soil movement by tillage （MBM2）. Sensitivity analysis of the proportion factor and distribution pattern of ^137Cs in the surface layer demonstrated the impact of ^137Cs enrichment on calculation of the soil erosion rate. Factors influencing the redistribution of fallout ^137Cs in landscape should be fully considered as calculating soil redistribution rate using ^137Cs technique.展开更多
A tillage experiment, consisting of moldboard plow （MP）, ridge tillage （RT）, and no-tillage （NT）, was performed in a randomized complete block design with four replicates to study the effect of 3-year tillage ma...A tillage experiment, consisting of moldboard plow （MP）, ridge tillage （RT）, and no-tillage （NT）, was performed in a randomized complete block design with four replicates to study the effect of 3-year tillage management on SOC content and its distribution in surface layer （30 cm） of a clay loam soil in northeast China. NT did not lead to significant increase of SOC in topsoil （0-5 cm） compared with MP and RT; however, the SOC content in NT soil was remarkably reduced at a depth of 5-20 cm. Accordingly, short-term （3-year） NT management tended to stratify SOC concentration, but not necessarily increase its storage in the plow layer for the soil.展开更多
The preliminary analysis of climatic variation in China during the last 39 years has been made in this paper. The results show that although the global climate is getting warmer, some parts of China are cooling. The ... The preliminary analysis of climatic variation in China during the last 39 years has been made in this paper. The results show that although the global climate is getting warmer, some parts of China are cooling. The warming only occurs in Northeast, North and the west part of Northwest China while the areas between about 35°N and Nanling Mountain, east of the Tibetan Plateau in China are getting cooler. The cooling centers are located in Sichuan, the south part of Shaanxi and the north part of Yunnan respectively. According to the theory of greenhouse effect, there are much precipitation at low and high latitudes and less precipitation in middle latitude. However, the precipitation in the most parts of China has been decreased, especially in North and Northwest China.展开更多
Currently, a large proportion of global fossil fuel emissions originate from large point sources such as power generation or industrial processes. This trend is expected to continue until the year 2030 and beyond. Car...Currently, a large proportion of global fossil fuel emissions originate from large point sources such as power generation or industrial processes. This trend is expected to continue until the year 2030 and beyond. Carbon capture and storage （CCS）, a straightforward and effective carbon reduction approach, will play a significant role in reducing emissions from these sources into the future if atmospheric carbon dioxide （CO2） emissions are to be stabilized and global warming limited below a threshold of 2 ℃. This review provides an update on the status of large scale integrated CCS technologies using solvent absorption for CO2 capture and provides an insight into the development of new solvents, including advanced amine solvents, amino acid salts, carbonate systems, aqueous ammonia, immiscible liquids and ionic liquids. These proposed new solvents aim to reduce the overall cost CO2 capture by improving the CO2 absorption rate, CO2 capture capacity, thereby reducing equipment size and decreasing the energy required for solvent regeneration.展开更多
The carbon dioxide （CO2） removal efficiency, reaction rate, and CO2 loading into aqueous blended monoethanolamine （MEA） ＋ 2-amino-2-methyl-l-propanol （AMP） solutions to enhance absorption characteristics of MEA...The carbon dioxide （CO2） removal efficiency, reaction rate, and CO2 loading into aqueous blended monoethanolamine （MEA） ＋ 2-amino-2-methyl-l-propanol （AMP） solutions to enhance absorption characteristics of MEA and AMP were carried out by the absorption/regeneration process. As a result, compared to aqueous MEA and AMP solutions, aqueous blended MEA ＋ AMP solutions have a higher CO2 loading than MEA and a higher reaction rate than AMP. The CO2 loading of rich amine of aqueous 18 wt.% MEA ＋ 12 wt.% AMP solution was 0.62 mol CO2/mol amine, which is 51.2% more than 30 wt.% MEA （0.41 mol CO2/mol amine）. Consequently, blending MEA and AMP could be an effective way to design considering economical efficiency and used to operate absorber for a long time.展开更多
Crop models can be useful tools ibr optimizing fertilizer management for a targeted crop yield while minimizing nutrient losses. In this paper, the parameters of the decision support system for agrotechnology transfer...Crop models can be useful tools ibr optimizing fertilizer management for a targeted crop yield while minimizing nutrient losses. In this paper, the parameters of the decision support system for agrotechnology transfer （DSSAT）-CERES-Maize were optimized using a new method to provide a better simulation of maize （Zea mays L.） growth and N upfake in response to different nitrogen application rates. Field data were collected from a 5 yr field experiment （2006-2010） on a Black soil （Typic hapludoll） in Gongzhuling, Jilin Province, Northeast China. After cultivar calibration, the CERES-Maize model was able to simulate aboveground biomass and crop yield of in the evaluation data set （n-RMSE=5.0-14.6%）, but the model still over-estimated aboveground N uptake （i.e., with E values from -4.4 to -21.3 kg N ha-~）. By analyzing DSSAT equation, N stress coefficient for changes in concentration with growth stage （CTCNP2） is related to N uptake. Further sensitivity analysis of the CTCNP2 showed that the DSSAT model simulated maize nitrogen uptake more precisely after the CTCNP2 coefficient was adjusted to the field site condition. The results indicated that in addition to calibrating 6 coefficients of maize cultivars, radiation use efficiency （RUE）, growing degree days for emergence （GDDE）, N stress coefficient, CTCNP2, and soil fertility factor （SLPF） also need to be calibrated in order to simulate aboveground biomass, yield and N uptake correctly. Independent validation was conducted using 2008-2010 experiments and the good agreement between the simulated and the measured results indicates that the DSSAT CERES-Maize model could be a useful tool for predicting maize production in Northeast China.展开更多
Supercritical carbon dioxide （scCO2） microemulsion was formed by supercritical CO2, H20, sodium bis（2-ethylhexyl） sulfosuccinate （AOT, surfactant） and C2HsOH （co-surfactant） under pressures higher than 8 MPa a...Supercritical carbon dioxide （scCO2） microemulsion was formed by supercritical CO2, H20, sodium bis（2-ethylhexyl） sulfosuccinate （AOT, surfactant） and C2HsOH （co-surfactant） under pressures higher than 8 MPa at 45 ℃. The fundamental characteristics of the scCO2 microemulsion and the minimum miscibility pressure （MMP） with Daqing oil were investigated with a high-pressure falling sphere viscometer, a high-pressure interfacial tension meter, a PVT cell and a slim tube test. The mechanism of the scCO2 microemulsion for enhancing oil recovery is discussed. The results showed that the viscosity and density of the scCO2 microemulsion were higher than those of the scCO2 fluid at the same pressure and temperature. The results of interfacial tension and slim tube tests indicated that the MMP of the scCO2 microemulsion and crude oil was lower than that of the scCO2 and crude oil at 45 ℃. It is the combined action of viscosity, density and MMP which made the oil recovery efficiency of the scCO2 microemulsion higher than that of the scCO2 fluid.展开更多
The large-scale use of antibiotics is causing serious water pollution problems,and it is of great significance to develop new technologies to remove antibiotics from water.As an environmentally friendly and economical...The large-scale use of antibiotics is causing serious water pollution problems,and it is of great significance to develop new technologies to remove antibiotics from water.As an environmentally friendly and economical adsorption material,carbon derived from biomass is a low-cost and feasible material for removing antibiotics in sewage,but the current removal efficiencies are not high enough for large-scale practical application.In this study,poplar wood chips are used as raw material,and a magnetic biochar is prepared by co-pyrolysis of poplar wood chips and FeCl_(3)/CaCl_(2)mixed molten salt.X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FTIR),N_(2)-isothermal adsorption and desorption,X-ray photoelectron spectroscopy(XPS)and scanning electron microscope(SEM)techniques showed the successful synthesis of Fe_(2)O_(3)/bioC composite.In-situ formed Fe_(2)O_(3)makes the biochar possess the characteristic of superparamagnetic,which is conducive to the recycling of biochar.Due to the etching effect of the molten salts,rough surface was formed on Fe_(2)O_(3)/bioC,result-ing in a maximum norfloxacin(NOR)adsorption ability up to 38.77 mg g^(−1)at pH 6.0.The NOR adsorption behavior on Fe_(2)O_(3)/bioC followed the pseudo second order kinetic model and the equilibrium data was best fitted the Langmuir model.In addition,the adsorption process of NOR on Fe_(2)O_(3)/bioC was thermodynamically spontaneous.The results show that this low-cost and reusable magnetic biochar has the potential for rapid and efficient removal of antibiotic from aqueous solution.展开更多
基金Project supported by the Hundred Talents Program of Chinese Academy of Sciences (No. K09Z3) the National Natural Science Foundation of China (Nos. 40271108 and 40471125).
文摘Soil and water losses through erosion have been serious in the black soil region of Northeast China. Therefore, a sloping cultivated land in Songnen Plain was selected as a case study to： 1） determine the ^137Cs reference inventory in the study area; 2） calculate erosion and deposition rates of black soil on different slope locations; 3） conduct a sensitivity analysis of some model parameters; and 4） compare overall outputs using four different models. Three transects were set in the field with five slope locations for each transect, including summit, shoulder-slope, back-slope, foot-slope, and toe-slope. Field measurements and model simulation were used to estimate a bomb-derived ^137Cs reference inventory in the study area. Soil erosion and deposition rates were estimated using four ^137Cs models and percentage of ^137Cs loss/gain. The ^137Cs reference value in the study area was 2 232.8 Bq m^-2 with ^137Cs showing a clear topographic pattern, decreasing from the summit to shoulder-slope, then increasing again at the foot-slope and reaching a maximum at the toe-slope, Predicted soil redistribution rates for different slope locations varied. Among models, the Yang Model （YANG-M） overestimated erosion loss but underestimated deposition. However, the standard mass balance model （MBM1） gave predictions similar to a mass balance model incorporating soil movement by tillage （MBM2）. Sensitivity analysis of the proportion factor and distribution pattern of ^137Cs in the surface layer demonstrated the impact of ^137Cs enrichment on calculation of the soil erosion rate. Factors influencing the redistribution of fallout ^137Cs in landscape should be fully considered as calculating soil redistribution rate using ^137Cs technique.
基金Project supported by the National Natural Science Foundation of China (Nos.40271108 and 40471125).
文摘A tillage experiment, consisting of moldboard plow （MP）, ridge tillage （RT）, and no-tillage （NT）, was performed in a randomized complete block design with four replicates to study the effect of 3-year tillage management on SOC content and its distribution in surface layer （30 cm） of a clay loam soil in northeast China. NT did not lead to significant increase of SOC in topsoil （0-5 cm） compared with MP and RT; however, the SOC content in NT soil was remarkably reduced at a depth of 5-20 cm. Accordingly, short-term （3-year） NT management tended to stratify SOC concentration, but not necessarily increase its storage in the plow layer for the soil.
基金This work is supported by National Environment and Protect Agency under Program 891205
文摘 The preliminary analysis of climatic variation in China during the last 39 years has been made in this paper. The results show that although the global climate is getting warmer, some parts of China are cooling. The warming only occurs in Northeast, North and the west part of Northwest China while the areas between about 35°N and Nanling Mountain, east of the Tibetan Plateau in China are getting cooler. The cooling centers are located in Sichuan, the south part of Shaanxi and the north part of Yunnan respectively. According to the theory of greenhouse effect, there are much precipitation at low and high latitudes and less precipitation in middle latitude. However, the precipitation in the most parts of China has been decreased, especially in North and Northwest China.
文摘Currently, a large proportion of global fossil fuel emissions originate from large point sources such as power generation or industrial processes. This trend is expected to continue until the year 2030 and beyond. Carbon capture and storage （CCS）, a straightforward and effective carbon reduction approach, will play a significant role in reducing emissions from these sources into the future if atmospheric carbon dioxide （CO2） emissions are to be stabilized and global warming limited below a threshold of 2 ℃. This review provides an update on the status of large scale integrated CCS technologies using solvent absorption for CO2 capture and provides an insight into the development of new solvents, including advanced amine solvents, amino acid salts, carbonate systems, aqueous ammonia, immiscible liquids and ionic liquids. These proposed new solvents aim to reduce the overall cost CO2 capture by improving the CO2 absorption rate, CO2 capture capacity, thereby reducing equipment size and decreasing the energy required for solvent regeneration.
基金supported by Korea Ministry of Environment (MOE) as "Human Resource Development Project for Waste to Energy"
文摘The carbon dioxide （CO2） removal efficiency, reaction rate, and CO2 loading into aqueous blended monoethanolamine （MEA） ＋ 2-amino-2-methyl-l-propanol （AMP） solutions to enhance absorption characteristics of MEA and AMP were carried out by the absorption/regeneration process. As a result, compared to aqueous MEA and AMP solutions, aqueous blended MEA ＋ AMP solutions have a higher CO2 loading than MEA and a higher reaction rate than AMP. The CO2 loading of rich amine of aqueous 18 wt.% MEA ＋ 12 wt.% AMP solution was 0.62 mol CO2/mol amine, which is 51.2% more than 30 wt.% MEA （0.41 mol CO2/mol amine）. Consequently, blending MEA and AMP could be an effective way to design considering economical efficiency and used to operate absorber for a long time.
基金funded by the National Basic Research Program of China (2007CB109306 and 2013CB127405)The authors acknowledge Ministry of Education,China,for providing the scholarship (2008325008)
文摘Crop models can be useful tools ibr optimizing fertilizer management for a targeted crop yield while minimizing nutrient losses. In this paper, the parameters of the decision support system for agrotechnology transfer （DSSAT）-CERES-Maize were optimized using a new method to provide a better simulation of maize （Zea mays L.） growth and N upfake in response to different nitrogen application rates. Field data were collected from a 5 yr field experiment （2006-2010） on a Black soil （Typic hapludoll） in Gongzhuling, Jilin Province, Northeast China. After cultivar calibration, the CERES-Maize model was able to simulate aboveground biomass and crop yield of in the evaluation data set （n-RMSE=5.0-14.6%）, but the model still over-estimated aboveground N uptake （i.e., with E values from -4.4 to -21.3 kg N ha-~）. By analyzing DSSAT equation, N stress coefficient for changes in concentration with growth stage （CTCNP2） is related to N uptake. Further sensitivity analysis of the CTCNP2 showed that the DSSAT model simulated maize nitrogen uptake more precisely after the CTCNP2 coefficient was adjusted to the field site condition. The results indicated that in addition to calibrating 6 coefficients of maize cultivars, radiation use efficiency （RUE）, growing degree days for emergence （GDDE）, N stress coefficient, CTCNP2, and soil fertility factor （SLPF） also need to be calibrated in order to simulate aboveground biomass, yield and N uptake correctly. Independent validation was conducted using 2008-2010 experiments and the good agreement between the simulated and the measured results indicates that the DSSAT CERES-Maize model could be a useful tool for predicting maize production in Northeast China.
基金support from the National Natural Science Fund (50904073)the CNPC Science and Technology Innovation Fund (2008D-5006-02-06)
文摘Supercritical carbon dioxide （scCO2） microemulsion was formed by supercritical CO2, H20, sodium bis（2-ethylhexyl） sulfosuccinate （AOT, surfactant） and C2HsOH （co-surfactant） under pressures higher than 8 MPa at 45 ℃. The fundamental characteristics of the scCO2 microemulsion and the minimum miscibility pressure （MMP） with Daqing oil were investigated with a high-pressure falling sphere viscometer, a high-pressure interfacial tension meter, a PVT cell and a slim tube test. The mechanism of the scCO2 microemulsion for enhancing oil recovery is discussed. The results showed that the viscosity and density of the scCO2 microemulsion were higher than those of the scCO2 fluid at the same pressure and temperature. The results of interfacial tension and slim tube tests indicated that the MMP of the scCO2 microemulsion and crude oil was lower than that of the scCO2 and crude oil at 45 ℃. It is the combined action of viscosity, density and MMP which made the oil recovery efficiency of the scCO2 microemulsion higher than that of the scCO2 fluid.
基金National Natural Science Foundation of China,Grant Number:21908242.
文摘The large-scale use of antibiotics is causing serious water pollution problems,and it is of great significance to develop new technologies to remove antibiotics from water.As an environmentally friendly and economical adsorption material,carbon derived from biomass is a low-cost and feasible material for removing antibiotics in sewage,but the current removal efficiencies are not high enough for large-scale practical application.In this study,poplar wood chips are used as raw material,and a magnetic biochar is prepared by co-pyrolysis of poplar wood chips and FeCl_(3)/CaCl_(2)mixed molten salt.X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FTIR),N_(2)-isothermal adsorption and desorption,X-ray photoelectron spectroscopy(XPS)and scanning electron microscope(SEM)techniques showed the successful synthesis of Fe_(2)O_(3)/bioC composite.In-situ formed Fe_(2)O_(3)makes the biochar possess the characteristic of superparamagnetic,which is conducive to the recycling of biochar.Due to the etching effect of the molten salts,rough surface was formed on Fe_(2)O_(3)/bioC,result-ing in a maximum norfloxacin(NOR)adsorption ability up to 38.77 mg g^(−1)at pH 6.0.The NOR adsorption behavior on Fe_(2)O_(3)/bioC followed the pseudo second order kinetic model and the equilibrium data was best fitted the Langmuir model.In addition,the adsorption process of NOR on Fe_(2)O_(3)/bioC was thermodynamically spontaneous.The results show that this low-cost and reusable magnetic biochar has the potential for rapid and efficient removal of antibiotic from aqueous solution.
