Reduction of drag torque in disengaged wet clutch is one of important potentials for vehicle transmission improvement. The flow of the oil film in clutch clearance is investigated. A three-dimension Navier-Stokes(N-S)...Reduction of drag torque in disengaged wet clutch is one of important potentials for vehicle transmission improvement. The flow of the oil film in clutch clearance is investigated. A three-dimension Navier-Stokes(N-S) equation based on laminar flow is presented to model the drag torque. Pressure and speed distribution in radial and circumferential directions are deduced. The theoretical analysis reveals that oil flow acceleration in radial direction caused by centrifugal force is the key reason for the shrinking of oil film as constant feeding flow rate. The peak drag torque occurs at the beginning of oil film shrinking. A variable is introduced to describe effective oil film area and drag torque after oil film shrinking is well evaluated with the variable. Under the working condition, tests were made to obtain drag torque curves at different clutch speed and oil viscosity. The tests confirm that simulation results agree with test data. The model performs well in the prediction of drag torque and lays a theoretical foundation to reduce it.展开更多
Reduction of drag torque is one of important potentials to improve transmission efficiency.Existing mathematical model of drag torque was not accurate to predict the decrease after oil film shrinking because of the di...Reduction of drag torque is one of important potentials to improve transmission efficiency.Existing mathematical model of drag torque was not accurate to predict the decrease after oil film shrinking because of the difficulty in modeling the flow pattern between two plates.Flow pattern was considered as laminar flow and full oil film in the gap between two plates in traditional model.Subsequent equivalent circumferential degree model presented an improvement in oil film shrinking due to centrifugal force,but was also based on full oil film in the gap,which resulted difference between model prediction and experimental data.The objective of this paper is to develop an accurate mathematical model for the above problem by using experimental verification.An experimental apparatus was set up to test drag torque of disengaged wet clutch consisting of single friction and separate plate.A high speed camera was used to record the flow pattern through transparent quartz disk plate.The visualization of flow pattern in the clearance was investigated to evaluate the characteristics of oil film shrinking.Visual test results reveal that the oil film begins to shrink from outer radius to inner radius at the stationary plate and only flows along the rotating plate after shrinking.Meanwhile,drag torque decreases sharply due to little contact area between the stationary plate and the oil.A three-dimensional Navier-Stokes （N-S） equation based on laminar flow is presented to model the drag torque.Pressure distributions in radial and circumferential directions as well as speed distributions are deduced.The model analysis reveals that the acceleration of flow in radial direction caused by centrifugal force is the key reason for the shrinking at the constant feeding flow rate.An approach to descript flow pattern was presented on the basis of visual observation.The drag torque predicted by the model agrees well with test data for non-grooved wet clutch.The proposed model enhances the precision for predicting drag torque,and lays down 展开更多
Considering the surface tension effect and centrifugal effect, a mathematical model based on Reynolds equation for predicting the drag torque of disengage wet clutches is presented. The model indicates that the equiva...Considering the surface tension effect and centrifugal effect, a mathematical model based on Reynolds equation for predicting the drag torque of disengage wet clutches is presented. The model indicates that the equivalent radius is a function of clutch speed and flow rate. The drag torque achieves its peak at a critical speed. Above this speed, drag torque drops due to the shrinking of the oil film. The model also points out that viscosity and flow rate effects on drag torque. Experimental results indicate that the model is reason-able and it performs well for predicting the drag torque peak.展开更多
基金supported by National Defense Arming Pre-researching Project(Grant No. 40402060102)
文摘Reduction of drag torque in disengaged wet clutch is one of important potentials for vehicle transmission improvement. The flow of the oil film in clutch clearance is investigated. A three-dimension Navier-Stokes(N-S) equation based on laminar flow is presented to model the drag torque. Pressure and speed distribution in radial and circumferential directions are deduced. The theoretical analysis reveals that oil flow acceleration in radial direction caused by centrifugal force is the key reason for the shrinking of oil film as constant feeding flow rate. The peak drag torque occurs at the beginning of oil film shrinking. A variable is introduced to describe effective oil film area and drag torque after oil film shrinking is well evaluated with the variable. Under the working condition, tests were made to obtain drag torque curves at different clutch speed and oil viscosity. The tests confirm that simulation results agree with test data. The model performs well in the prediction of drag torque and lays a theoretical foundation to reduce it.
基金supported by National Defense Arming Pre-researching Project of China(Grant No.40402060102)
文摘Reduction of drag torque is one of important potentials to improve transmission efficiency.Existing mathematical model of drag torque was not accurate to predict the decrease after oil film shrinking because of the difficulty in modeling the flow pattern between two plates.Flow pattern was considered as laminar flow and full oil film in the gap between two plates in traditional model.Subsequent equivalent circumferential degree model presented an improvement in oil film shrinking due to centrifugal force,but was also based on full oil film in the gap,which resulted difference between model prediction and experimental data.The objective of this paper is to develop an accurate mathematical model for the above problem by using experimental verification.An experimental apparatus was set up to test drag torque of disengaged wet clutch consisting of single friction and separate plate.A high speed camera was used to record the flow pattern through transparent quartz disk plate.The visualization of flow pattern in the clearance was investigated to evaluate the characteristics of oil film shrinking.Visual test results reveal that the oil film begins to shrink from outer radius to inner radius at the stationary plate and only flows along the rotating plate after shrinking.Meanwhile,drag torque decreases sharply due to little contact area between the stationary plate and the oil.A three-dimensional Navier-Stokes （N-S） equation based on laminar flow is presented to model the drag torque.Pressure distributions in radial and circumferential directions as well as speed distributions are deduced.The model analysis reveals that the acceleration of flow in radial direction caused by centrifugal force is the key reason for the shrinking at the constant feeding flow rate.An approach to descript flow pattern was presented on the basis of visual observation.The drag torque predicted by the model agrees well with test data for non-grooved wet clutch.The proposed model enhances the precision for predicting drag torque,and lays down
基金Sponsored by the Ministerial Level Advanced Research Foundation(10506024)
文摘Considering the surface tension effect and centrifugal effect, a mathematical model based on Reynolds equation for predicting the drag torque of disengage wet clutches is presented. The model indicates that the equivalent radius is a function of clutch speed and flow rate. The drag torque achieves its peak at a critical speed. Above this speed, drag torque drops due to the shrinking of the oil film. The model also points out that viscosity and flow rate effects on drag torque. Experimental results indicate that the model is reason-able and it performs well for predicting the drag torque peak.
