In order to maintain a uniform distribution of pareto-front solutions, a modified NSGA-II algorithm coupled with a dynamic crowding distance(DCD) method is proposed for the multi-objective optimization of a mixed-flow...In order to maintain a uniform distribution of pareto-front solutions, a modified NSGA-II algorithm coupled with a dynamic crowding distance(DCD) method is proposed for the multi-objective optimization of a mixed-flow pump impeller. With the pump meridional section fixed, ten variables along the shroud and hub are selected to control the blade load by using a three-dimensional inverse design method. Hydraulic efficiency, along with impeller head, is applied as an optimization objective; and a radial basis neural network(RBNN) is adopted to approximate the objective function with 82 training samples. Local sensitivity analysis shows that decision variables have different impacts on the optimization objectives. Instead of randomly selecting one solution to implement, a technique for ordering preferences by similarity to ideal solution(TOPSIS) is introduced to select the best compromise solution(BCS) from pareto-front sets. The proposed method is applied to optimize the baseline model, i.e. a mixed- flow waterjet pump whose specific speed is 508 min?1?m3s?1?m. The performance of the waterjet pump was experimentally tested. Compared with the baseline model, the optimized impeller has a better hydraulic efficiency of 92% as well as a higher impeller head at the design operation point. Furthermore, the off-design performance is improved with a wider highefficiency operation range. After optimization, velocity gradients on the suction surface are smoother and flow separations are eliminated at the blade inlet part. Thus, the authors believe the proposed method is helpful for optimizing the mixed-flow pumps.展开更多
Extremely hard and abrasive rocks pose great challenges to the past and ongoing TBM projects by increasing cutter wear and reducing penetration rates.A considerable amount of research has been conducted to improve the...Extremely hard and abrasive rocks pose great challenges to the past and ongoing TBM projects by increasing cutter wear and reducing penetration rates.A considerable amount of research has been conducted to improve the performance of TBMs in those challenging grounds by either improving the capacity of TBMs or developing assisting rock breakage methods.This paper first highlights the challenges of hard and abrasive rocks on TBM tunneling through case studies.It then presents the development of hard rock TBMs and reviews the technologies that can be used individually or as assistance to mechanical excavators to break hard rocks.Emphases are placed on technologies of high pressure waterjet,laser and microwave.The state of the art of field and laboratory research,problems and research directions of those technologies are discussed.The assisting methods are technically feasible;however,the main challenges of using those methods in the field are that the energy consumption can be over 10 times high and that the existing equipments have robustness problems.More research should be conducted to study the overall energy consumption using TBMs and the assisting methods.Pulsed waterjet,laser and microwave technologies should also be developed to make the assistance economically viable.展开更多
In dealing with abrasive waterjet machining（AWJM） simulation,most literatures apply finite element method（FEM） to build pure waterjet models or single abrasive particle erosion models.To overcome the mesh distorti...In dealing with abrasive waterjet machining（AWJM） simulation,most literatures apply finite element method（FEM） to build pure waterjet models or single abrasive particle erosion models.To overcome the mesh distortion caused by large deformation using FEM and to consider the effects of both water and abrasive,the smoothed particle hydrodynamics（SPH） coupled FEM modeling for AWJM simulation is presented,in which the abrasive waterjet is modeled by SPH particles and the target material is modeled by FEM.The two parts interact through contact algorithm.Utilizing this model,abrasive waterjet with high velocity penetrating the target materials is simulated and the mechanism of erosion is depicted.The relationships between the depth of penetration and jet parameters,including water pressure and traverse speed,etc,are analyzed based on the simulation.The simulation results agree well with the existed experimental data.The mixing multi-materials SPH particles,which contain abrasive and water,are adopted by means of the randomized algorithm and material model for the abrasive is presented.The study will not only provide a new powerful tool for the simulation of abrasive waterjet machining,but also be beneficial to understand its cutting mechanism and optimize the operating parameters.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.5137610051306018+4 种基金51206087and 51179091)the National Key Technology Research and Development Program(Grant No.2011BAF03B01)State Key Laboratory for Hydroscience and Engineering(Grant Nos.2014-KY-05 and 2015-E-03)Laboratory of Science and Technology on Waterjet Propulsion
文摘In order to maintain a uniform distribution of pareto-front solutions, a modified NSGA-II algorithm coupled with a dynamic crowding distance(DCD) method is proposed for the multi-objective optimization of a mixed-flow pump impeller. With the pump meridional section fixed, ten variables along the shroud and hub are selected to control the blade load by using a three-dimensional inverse design method. Hydraulic efficiency, along with impeller head, is applied as an optimization objective; and a radial basis neural network(RBNN) is adopted to approximate the objective function with 82 training samples. Local sensitivity analysis shows that decision variables have different impacts on the optimization objectives. Instead of randomly selecting one solution to implement, a technique for ordering preferences by similarity to ideal solution(TOPSIS) is introduced to select the best compromise solution(BCS) from pareto-front sets. The proposed method is applied to optimize the baseline model, i.e. a mixed- flow waterjet pump whose specific speed is 508 min?1?m3s?1?m. The performance of the waterjet pump was experimentally tested. Compared with the baseline model, the optimized impeller has a better hydraulic efficiency of 92% as well as a higher impeller head at the design operation point. Furthermore, the off-design performance is improved with a wider highefficiency operation range. After optimization, velocity gradients on the suction surface are smoother and flow separations are eliminated at the blade inlet part. Thus, the authors believe the proposed method is helpful for optimizing the mixed-flow pumps.
基金Projects(3205009419,3205002001C3)supported by Fundamental Research Funds for Central Universities,China。
文摘Extremely hard and abrasive rocks pose great challenges to the past and ongoing TBM projects by increasing cutter wear and reducing penetration rates.A considerable amount of research has been conducted to improve the performance of TBMs in those challenging grounds by either improving the capacity of TBMs or developing assisting rock breakage methods.This paper first highlights the challenges of hard and abrasive rocks on TBM tunneling through case studies.It then presents the development of hard rock TBMs and reviews the technologies that can be used individually or as assistance to mechanical excavators to break hard rocks.Emphases are placed on technologies of high pressure waterjet,laser and microwave.The state of the art of field and laboratory research,problems and research directions of those technologies are discussed.The assisting methods are technically feasible;however,the main challenges of using those methods in the field are that the energy consumption can be over 10 times high and that the existing equipments have robustness problems.More research should be conducted to study the overall energy consumption using TBMs and the assisting methods.Pulsed waterjet,laser and microwave technologies should also be developed to make the assistance economically viable.
基金supported by Shandong Provincial Natural Science Foundation of China (Grant No. Y2007A07)
文摘In dealing with abrasive waterjet machining（AWJM） simulation,most literatures apply finite element method（FEM） to build pure waterjet models or single abrasive particle erosion models.To overcome the mesh distortion caused by large deformation using FEM and to consider the effects of both water and abrasive,the smoothed particle hydrodynamics（SPH） coupled FEM modeling for AWJM simulation is presented,in which the abrasive waterjet is modeled by SPH particles and the target material is modeled by FEM.The two parts interact through contact algorithm.Utilizing this model,abrasive waterjet with high velocity penetrating the target materials is simulated and the mechanism of erosion is depicted.The relationships between the depth of penetration and jet parameters,including water pressure and traverse speed,etc,are analyzed based on the simulation.The simulation results agree well with the existed experimental data.The mixing multi-materials SPH particles,which contain abrasive and water,are adopted by means of the randomized algorithm and material model for the abrasive is presented.The study will not only provide a new powerful tool for the simulation of abrasive waterjet machining,but also be beneficial to understand its cutting mechanism and optimize the operating parameters.
