It is a novel idea to make steamed bread by adding potato flour into wheat flour considering the production and nutritional factors of potato. In this study, the influence of potato flour（0–35%） on dough rheology a...It is a novel idea to make steamed bread by adding potato flour into wheat flour considering the production and nutritional factors of potato. In this study, the influence of potato flour（0–35%） on dough rheology and quality of steamed bread were investigated. Potato flour addition significantly influenced the dough rheological properties and steamed bread quality, such as increased water absorption, the maximum gaseous release height, total volume of CO_2 and hardness, while decreased dough stability and specific volume of steamed bread. Moreover, correlation analysis suggested that dough height at the maximum development time, dough stability, water absorption and the phase tangent can be used for predicting the technological quality of steamed bread. Potato-wheat steamed bread had higher dietary fibre, ash content and antioxidant activity than those of wheat steamed bread. The estimated glycemic index decreased from 73.63（0%） to 60.01（35%）. Considering the sensory evaluation, the steamed bread with 20% potato flour is acceptable. In conclusion, adding appropriate quantity of potato flour to wheat flour for steamed bread production will not only maintain the technological quality, but also can improve the nutritional value of the steamed bread.展开更多
High strength low alloy（HSLA） steels have been widely used in pipelines,power plant components,civil structures and so on,due to their outstanding mechanical properties as high strength and toughness,and excellent w...High strength low alloy（HSLA） steels have been widely used in pipelines,power plant components,civil structures and so on,due to their outstanding mechanical properties as high strength and toughness,and excellent weldability.Multi-phase microstructures containing acicular ferrite or acicular ferrite dominated phase have been proved to possess good comprehensive properties in HSLA steels.This paper mainly focuses on the formation mechanisms and control methods of acicular ferrite in HSLA steels.Effect of austenitizing conditions,continuous cooling rate,and isothermal quenching time and temperature on acicular ferrite transformation was reviewed.Furthermore,the modified process to control the formation of multi-phase microstructures containing acicular ferrite,as intercritical heat treatments,step quenching treatments and thermo-mechanical controlled processing,was summarized.The favorable combination of mechanical properties can be achieved by these modified treatments.展开更多
In this paper, the coupled thermo-mechanical （TM） processes in the AEspoe Pillar Stability Experiment （APSE） carried out by the Swedish Nuclear Fuel and Waste Management Company （SKB） were simulated using both c...In this paper, the coupled thermo-mechanical （TM） processes in the AEspoe Pillar Stability Experiment （APSE） carried out by the Swedish Nuclear Fuel and Waste Management Company （SKB） were simulated using both continuum and discontinuum based numerical methods. Two-dimensional （2D） and three- dimensional （3D） finite element method （FEM） and 2D distinct element method （DEM） with particles were used. The main objective for the large scale in situ experiment is to investigate the yielding strength of crystalline rock and the formation of the excavation disturbed/damaged zone （EDZ） during excavation of two boreholes, pressurizing of one of the boreholes and heating. For the DEM simulations, the heat flow algorithm was newly introduced into the original code. The calculated stress, displacement and temperature distributions were compared with the ones obtained from in situ measurements and FEM simulations. A parametric study for initial microcracks was also performed to reproduce the spalling phenomena observed in the APSE.展开更多
2A97 Al-Li alloy was processed by thermo-mechanical treatment at different pre-stretch deformations of 0, 3% and 6%. The microstrucatre observation results reveal that some δ＇ and T1 precipitates are found in a（Al...2A97 Al-Li alloy was processed by thermo-mechanical treatment at different pre-stretch deformations of 0, 3% and 6%. The microstrucatre observation results reveal that some δ＇ and T1 precipitates are found in a（Al） matrix of 2A97 alloy processed by the heat treatment with no pre-stretch deformation. When the pre-stretch deformation is 3% and 6%, respectively, amounts of tiny T1 and a few of S＇ precipitates precipitates are observed in the microstructures of 2A97 alloy. The tensile test results show that the tensile properties of 2A97 alloys are improved via thermo-mechanical treatment. When the pre-stretch deformation is from 0, 3% to 6%, the ultimate tensile strength values of the 2A97 alloys increase gradually from 447.7, 516.5 to 534.3 MPa, and the elongations decrease from 17.6%, 12.8% to 10.2%, respectively. Moreover, with increasing pre-stretch deformation amount from 0 to 6%, the in-plane anisotropy value of 2A97 alloys becomes more obvious.展开更多
The diversity of microstructure and properties of 830 MPa grade pipeline steel containing chromium was investigated by optical microscope and transmission electron microscopy. The main microstructures were multiple co...The diversity of microstructure and properties of 830 MPa grade pipeline steel containing chromium was investigated by optical microscope and transmission electron microscopy. The main microstructures were multiple configurations, containing lath bainite and granule bainitc. Mechanical properties test results showed that the yield strength and tensile strength improved with increasing chromium content. The toughness and elongation decreased at the same time, so temper process was introduced. Appling proper temper parameters, the values of toughness and elongation were improved dramatically, and the strength decreased slightly.展开更多
Fully-coupled thermo-mechanical simulations are implemented in COMSOL Multiphysics to investigate micro-scale stress-strain variability in pegmatite specimens subjected to thermal loading using microwaves. Thermally-i...Fully-coupled thermo-mechanical simulations are implemented in COMSOL Multiphysics to investigate micro-scale stress-strain variability in pegmatite specimens subjected to thermal loading using microwaves. Thermally-induced compressive and tensile stresses increase as the microwave irradiation duration increases. The dielectric constant, coefficient of expansion, and type and size of mineralogical boundary have significant impacts on the responses of the rock to microwave irradiation. The maximum principal stress of the chlorite is the smallest, indicating that the chlorite experiences the most damage under microwave irradiation, followed by the quartz. The maximum principal stress values of plagioclase and orthoclase are larger, indicating that they are likely to incur the least damage. Where quartz or chlorite is dominant, the resulting von Mises stresses are consistently higher after 120 s of microwave irradiation. The rate of generation of von Mises stresses increases most rapidly along the interface between quartz and plagioclase, and the interface between quartz and orthoclase, followed by the interface between quartz and chlorite, and finally the interface between plagioclase and orthoclase. The presented modeling approach provides a practical method to investigate stress-strain relationships within mineralogical boundaries inside a rock thin section.展开更多
The aim of this study was to simulate the solidification process of beam blank continuous casting, and then find the reasons for the typical defects of the beam blank. A two-dimensional transient coupled finite elemen...The aim of this study was to simulate the solidification process of beam blank continuous casting, and then find the reasons for the typical defects of the beam blank. A two-dimensional transient coupled finite element model has been developed to compute the temperature and stress profile in beam blank continuous casting. The enthalpy method was used in the heat conduction equation. The thermo-mechanical property in the mushy zone was taken into consideration in this calculation. It is shown that at the mold exit the thickness of the shell had its maximum value at the flange tip and its minimum value at the fillet. The temperature had a great fluctuation on the surface of the beam blank in the secondary cooling zone. At the unbending point, the surface temperature of the web was in the brittleness temperature range under the present condition. To ensure the quality, it is necessary to weaken the intensity of secondary cooling. At the mold exit the equivalent stress and strain have higher values at the flange tip and at the web. From the spray 1 to the unbending point, the maximum values of stress and strain gradually moved to the internal section of the flange tip and the web. However, whenever, there were bigger stress and strain values near the flange tip and the web than in the other parts, it must be very easy to generate cracks at those positions. Now, online verification of this simulation has been developed, which has proved to be very useful and efficient to instruct the practical production of beam blank continuous casting.展开更多
The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron m...The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results confirm that the strength of TC4 alloy can be improved obviously by LTTMT processing, which combines strain strengthening with aging strengthening. The effect of LTTMT on the alloy depends on the microstructure of the refined and dispersed a＋fl phase on the basis of high dislocation density by pre-deformation below recrystallization temperature. The tensile strength decreases with the increase of pre-deformation reduction. The optimal processing parameters of LTTMT for TC4 alloy are as follows： solution treatment at 900 ℃ for 15 min, pre-deformation in the range of 600-700 ℃ with a reduction of 35%, finally aging at 540 ℃ for 4 h followed by air-cooling.展开更多
SMPU （shape memory polyurethane） non-ionomers and ionomers, synthesized with poly（c-caprolactone） （PCL）, 4, 4＇-diphenylmethane diisocyanate （MDI）, 1,4-butanediol （BDO）, dimethylolpropionic acid （DMPA） wer...SMPU （shape memory polyurethane） non-ionomers and ionomers, synthesized with poly（c-caprolactone） （PCL）, 4, 4＇-diphenylmethane diisocyanate （MDI）, 1,4-butanediol （BDO）, dimethylolpropionic acid （DMPA） were measured with cyclic tensile test and strain recovery test. The relations between the structure and shape memory effect of these two series were studied with respect to the ionic group content and the effect of neutralization. The resulting data indicate that, with the introduction of asymmetrical extender, the stress at 100% elongation is decreased for PU non-ionomer and ionomer series, especially lowered sharply for non-ionomer series; the fixation ratio of ionomer series is not affected obviously by the ionic group content; the total recovery ratio of ionomer series is decreased greatly. After sufficient relaxation time for samples stretched beforehand, the switching temperature is raised slightly, whereas the recovery ratio measured with strain recovery test method is lowered with increased DMPA content. The characterization with FT-IR, DSC, DMA elucidated that, the ordered hard domain of the two series is disrupted with the introduction of DMPA which causes more hard segments to dissolve in soft phase; ionic groups on hard segment enhance the cohesion between hard segments especially at high ionic group content and significantly facilitate the phase separation compared with the corresponding non-ionomer at moderate ionic group content.展开更多
The objective of this study is to seek solutions to reduce the impact of buildings on climate change and to promote the use of local bio-sourced or geo-sourced materials for sustainable construction. Different samples...The objective of this study is to seek solutions to reduce the impact of buildings on climate change and to promote the use of local bio-sourced or geo-sourced materials for sustainable construction. Different samples of raw earth from 3 sites were taken in the commune of Mlomp. Geotechnical tests showed that the raw earth samples from sites 2 and 3 have more clay fraction while site 1 contains more sand. The fact of integrating fibers from crushed palm leaves (Borassus aethiopum) (2%, 4% and 6%) into the 3 raw earth samples reduced the mechanical resistance to compression and traction of the 3 raw earths. The experimental results of thermal tests on samples of earth mixtures with crushed Palma leaf fibers show a decrease in thermal conductivity as well as thermal effusivity as the percentages increase (2%, 4% and 6%) of fibers in raw earth for the 3 sites. This shows that this renewable composite material can help improve the thermal insulation of building envelopes.展开更多
The material characteristics of a structure will change with temperature variation,and will induce stress within the structure.Currently,the optimal design for the topology of compliant mechanisms is mainly performed ...The material characteristics of a structure will change with temperature variation,and will induce stress within the structure.Currently,the optimal design for the topology of compliant mechanisms is mainly performed in single physical field.However,when compliant mechanisms work in high temperature environments,their displacement outputs are generated not only by mechanical load,but also by the temperature variation which may become the prominent factor.Therefore,the influence of temperature must be considered in the design.In this paper,a novel optimization method for multi-objective topology of thermo-mechanical compliant mechanisms is presented.First,the thermal field is analyzed with finite-element method,where the thermal strain is taken into account in the constitutive relation,and the equivalent nodal thermal load is derived with the principle of virtual work.Then the thermal load is converted into physical loads in elastic field,and the control equation of the thermo-mechanical compliant mechanism is obtained.Second,the mathematical model of the multi-objective topology optimization is built by incorporating both the flexibility and stiffness.Meanwhile,the coupling sensitivity function and the sensitivity analysis equations of thermal steady-state response are derived.Finally,optimality criteria algorithm is employed to obtain numerical solution of the multi-objective topology optimization.Numerical examples show that the compliant mechanisms have better performance and are more applicable if the temperature effect is taken into account in the design process.The presented modeling and analysis methods provide a new idea and an effective approach to topology optimization of compliant mechanisms in electrothermic coupling field and multiphysics fields.展开更多
Gleeble1500 thermo-mechanical simulation machine is considered to be the first grade equipment in materials' research. However, it is seldom used in superplastic research. Perhaps this is because its specimen'...Gleeble1500 thermo-mechanical simulation machine is considered to be the first grade equipment in materials' research. However, it is seldom used in superplastic research. Perhaps this is because its specimen's heating method is not suitable to get large elongation. Elongation is an important parameter to evaluate superplasticity, but some other parameters such as the relationship between stress and strain rate are more important than elongation-it is an essential property to superplasticity. The stress-strain rate relationship can be very easily and very accu- rately got with Gleeble machine than with some other simlar equipment, and the relationship between microstructure and superplastic deformation is more easily examined with Gleeble. Present authors have got some new achievement in anisotropy, heterogeneity of superplastic deformation, and first put forward the regulation of dynamic equilibrium in microstructural evolution during superplastic deformation. All of these have been concluded from the experimental results mainly through Gleeble as well as the microstructural examination.The research work has got the support of National Natural Science Foundation and some international cooperation. Some theoretic and experimental results have been used in the practice of superplastic forming. Obvious effect of reducing cost and improving quality of formed parts has been achieved.展开更多
The Aspoe Pillar Stability Experiment （APSE） was conducted to study the rock mass response in a heated rock pillar between two large boreholes. This paper summarizes the back calculations of the APSE using a two-dim...The Aspoe Pillar Stability Experiment （APSE） was conducted to study the rock mass response in a heated rock pillar between two large boreholes. This paper summarizes the back calculations of the APSE using a two-dimensional （2D） fracture propagation code FRACOD. To be able to model all the loading phases of the APSE, including the thermal loading, the code was improved in several ways. A sequential excavation function was developed to model promptly the stepwise changing loading geometry. Prior to the mod- elling, short-term compressive strength test models were set up aiming to reproduce the stress-strain behaviour observed for the Aspoe diorite in laboratory. These models simulate both the axial and lateral strains of radial-controlled laboratory tests, The volumetric strain was calculated from the simulations and compared with the laboratory results, The pillar models include vertical and horizontal 2D models from where the stress in the pillar wall was investigated, The vertical model assesses the stability of the experimental rock volume and suggests the resultant stress below the tunnel floor in the pillar area. The horizontal model considers cross-sections of the pillar between the two large boreholes. The horizon- tal model is used to simulate the evolution of the stress in the rock mass during the excavation of the boreholes and during and the heating phase to give an estimation of the spalling strength. The modelling results suggest that the excavation-induced stresses will cause slight fracturing in the pillar walls, if the strength of the APSE pillar is set to about 123 MPa. Fracture propagation driven by thermal loading leads to minor spalling. The thermal evolution, elastic behaviour and brittle failure observed in the experiment are well reflected by the models.展开更多
Effects of micro-alloying elements and production process on microstructure, mechanical properties and precipitates of 600 MPa grade rebars were studied by using pilot test, metallographic observa- tion, tensile test,...Effects of micro-alloying elements and production process on microstructure, mechanical properties and precipitates of 600 MPa grade rebars were studied by using pilot test, metallographic observa- tion, tensile test, thermodynamic calculation and transmission electron microscopy. The results show that the tested steels are composed of ferrite and pearlite, in which the conterlt range of pearlite is 33%-45%. For vanadium micro-alloyed steel, interphase preeipitation Strengthening effect of V can be promoted and the yield strength of tested steels can be increased with increasing V content and de- creasing finishing rolling temperature. The temperature of terminated cooling should be more than 700 ℃ when the water cooling is used. When niobium is added to the steel, more coarse （Nb,V）C,N precipitates are generated at high temperature, so that the solid solubility of precipitated phases of vanadium is reduced and the precipitation strengthening effect of vanadium is weakened.展开更多
The effects of T916 thermo-mechanical process on microstructures, mechanical properties and ballistic resistance of 2519A aluminum alloy were investigated by optical microscopy （OM）, transmission electron microscopy...The effects of T916 thermo-mechanical process on microstructures, mechanical properties and ballistic resistance of 2519A aluminum alloy were investigated by optical microscopy （OM）, transmission electron microscopy （TEM）, tensile tests and ballistic resistance test. After T916 treatment, the yield strength, tensile strength and elongation rate of 2519A aluminum alloy reach 501 MPa, 540 MPa and 14%, respectively. And the ballistic limit velocity of 2519A-T916 alloy （30 mm in thickness） is 715 rn/s. The microstructure varies near the sidewalls of crater. The interrupted ageing contributes to these excellent properties of the alloy. During T916 process, the precipitation of Guinier Preston （GP） zone is finer and denser during the interrupted ageing, thus resulting in well precipitated strengthening phase.展开更多
Three friction welding processes are compared for temperature, stresses and strains, as well as strain rates developed in the early phases of the processes, which are essential in their successful development. These a...Three friction welding processes are compared for temperature, stresses and strains, as well as strain rates developed in the early phases of the processes, which are essential in their successful development. These are friction stir welding （FSW）, linear friction welding （LFW） and rotary friction welding （RFW）. Their common characteristic is the use of friction to generate adequate energy and raise temperature locally in order to create favorable conditions for welding at the interface between two parts. Although the mode of movement is different for each one of them, welds are produced through plastic deformation. The Lagrangian and coupled Eulerian-Lagrangian numer- ical models developed have produced results which are in qualitative agreement with experiments and have shed a light on the commonalities of these friction welding processes展开更多
Systematic physical simulation of thermo-mechanical processing routes has been ap-plied on a Gleeble 1500 simulator to four copper alloys (mass %) Cu-0.57Co-0.32Si,Cu-0.55Cr-0.065P, Cu-0.22Zr-0.035Si and Cu-1.01Ni-0.4...Systematic physical simulation of thermo-mechanical processing routes has been ap-plied on a Gleeble 1500 simulator to four copper alloys (mass %) Cu-0.57Co-0.32Si,Cu-0.55Cr-0.065P, Cu-0.22Zr-0.035Si and Cu-1.01Ni-0.43Si aimed at clarifying theinfluences of processing conditions on their final properties, strength and electricalconductivity. Flow curves were determined over wide temperature and strain rateranges. Hardness was used as a measure of the strength level achieved. High hard-ness was obtained as using equal amounts (strains 0.5) of cold deformation beforeand after the precipitation annealing stage. The maximum values achieved for theCu-Co-Si, Cu-Cr-P, Cu-Zr-Si and Cu-Ni-Si alloys were 190, 165, 178 and 193 HV5,respectively. A thermo-mechanical schedule involving the hot deformation-ageing-colddeformation stages showed even better results for the Cu-Zr-Si alloy. Consequently,the processing routes were designed based on simulation test results and wires of 5 and2mm in diameters have been successfully processed in the industrial scale.展开更多
基金financed by the Public Welfare Industry(Agriculture)Research Project of China(201503001-2)the Agricultural Special Financial in 2015 of Chinathe Basic Research Expenses Budget Incremental Project of Chinese Academy of Agricultural Sciences(2014ZL009)
文摘It is a novel idea to make steamed bread by adding potato flour into wheat flour considering the production and nutritional factors of potato. In this study, the influence of potato flour（0–35%） on dough rheology and quality of steamed bread were investigated. Potato flour addition significantly influenced the dough rheological properties and steamed bread quality, such as increased water absorption, the maximum gaseous release height, total volume of CO_2 and hardness, while decreased dough stability and specific volume of steamed bread. Moreover, correlation analysis suggested that dough height at the maximum development time, dough stability, water absorption and the phase tangent can be used for predicting the technological quality of steamed bread. Potato-wheat steamed bread had higher dietary fibre, ash content and antioxidant activity than those of wheat steamed bread. The estimated glycemic index decreased from 73.63（0%） to 60.01（35%）. Considering the sensory evaluation, the steamed bread with 20% potato flour is acceptable. In conclusion, adding appropriate quantity of potato flour to wheat flour for steamed bread production will not only maintain the technological quality, but also can improve the nutritional value of the steamed bread.
基金the China National Funds for Distinguished Young Scientists (Grant No.51325401)the National Magnetic Confinement Fusion Energy Research Project (Grant No.2015GB119001)the National Natural Science Foundation of China (Grant Nos.51501126,51474156 and U1660201) for grant and financial support
文摘High strength low alloy（HSLA） steels have been widely used in pipelines,power plant components,civil structures and so on,due to their outstanding mechanical properties as high strength and toughness,and excellent weldability.Multi-phase microstructures containing acicular ferrite or acicular ferrite dominated phase have been proved to possess good comprehensive properties in HSLA steels.This paper mainly focuses on the formation mechanisms and control methods of acicular ferrite in HSLA steels.Effect of austenitizing conditions,continuous cooling rate,and isothermal quenching time and temperature on acicular ferrite transformation was reviewed.Furthermore,the modified process to control the formation of multi-phase microstructures containing acicular ferrite,as intercritical heat treatments,step quenching treatments and thermo-mechanical controlled processing,was summarized.The favorable combination of mechanical properties can be achieved by these modified treatments.
基金conducted within the context of the international DECOVALEX Project (DEvelopment of COupled models and their VALidation against EXperiments)financed by Japan Atomic Energy Agency (JAEA) who was also one of the Funding Organizations of the projectChrister Anders-son from Swedish Nuclear Fuel and Waste Management Co.(SKB),Sweden
文摘In this paper, the coupled thermo-mechanical （TM） processes in the AEspoe Pillar Stability Experiment （APSE） carried out by the Swedish Nuclear Fuel and Waste Management Company （SKB） were simulated using both continuum and discontinuum based numerical methods. Two-dimensional （2D） and three- dimensional （3D） finite element method （FEM） and 2D distinct element method （DEM） with particles were used. The main objective for the large scale in situ experiment is to investigate the yielding strength of crystalline rock and the formation of the excavation disturbed/damaged zone （EDZ） during excavation of two boreholes, pressurizing of one of the boreholes and heating. For the DEM simulations, the heat flow algorithm was newly introduced into the original code. The calculated stress, displacement and temperature distributions were compared with the ones obtained from in situ measurements and FEM simulations. A parametric study for initial microcracks was also performed to reproduce the spalling phenomena observed in the APSE.
文摘2A97 Al-Li alloy was processed by thermo-mechanical treatment at different pre-stretch deformations of 0, 3% and 6%. The microstrucatre observation results reveal that some δ＇ and T1 precipitates are found in a（Al） matrix of 2A97 alloy processed by the heat treatment with no pre-stretch deformation. When the pre-stretch deformation is 3% and 6%, respectively, amounts of tiny T1 and a few of S＇ precipitates precipitates are observed in the microstructures of 2A97 alloy. The tensile test results show that the tensile properties of 2A97 alloys are improved via thermo-mechanical treatment. When the pre-stretch deformation is from 0, 3% to 6%, the ultimate tensile strength values of the 2A97 alloys increase gradually from 447.7, 516.5 to 534.3 MPa, and the elongations decrease from 17.6%, 12.8% to 10.2%, respectively. Moreover, with increasing pre-stretch deformation amount from 0 to 6%, the in-plane anisotropy value of 2A97 alloys becomes more obvious.
文摘The diversity of microstructure and properties of 830 MPa grade pipeline steel containing chromium was investigated by optical microscope and transmission electron microscopy. The main microstructures were multiple configurations, containing lath bainite and granule bainitc. Mechanical properties test results showed that the yield strength and tensile strength improved with increasing chromium content. The toughness and elongation decreased at the same time, so temper process was introduced. Appling proper temper parameters, the values of toughness and elongation were improved dramatically, and the strength decreased slightly.
基金supported by the US National Science Foundation (CMMI award 1550307)the China Scholarship Council for financial support as a visiting scholar at the Colorado School of Mines (Grant No. 201706375077)
文摘Fully-coupled thermo-mechanical simulations are implemented in COMSOL Multiphysics to investigate micro-scale stress-strain variability in pegmatite specimens subjected to thermal loading using microwaves. Thermally-induced compressive and tensile stresses increase as the microwave irradiation duration increases. The dielectric constant, coefficient of expansion, and type and size of mineralogical boundary have significant impacts on the responses of the rock to microwave irradiation. The maximum principal stress of the chlorite is the smallest, indicating that the chlorite experiences the most damage under microwave irradiation, followed by the quartz. The maximum principal stress values of plagioclase and orthoclase are larger, indicating that they are likely to incur the least damage. Where quartz or chlorite is dominant, the resulting von Mises stresses are consistently higher after 120 s of microwave irradiation. The rate of generation of von Mises stresses increases most rapidly along the interface between quartz and plagioclase, and the interface between quartz and orthoclase, followed by the interface between quartz and chlorite, and finally the interface between plagioclase and orthoclase. The presented modeling approach provides a practical method to investigate stress-strain relationships within mineralogical boundaries inside a rock thin section.
基金supported by the Hebei Provincial Natural Science Foundation of China(No.E2007000591).
文摘The aim of this study was to simulate the solidification process of beam blank continuous casting, and then find the reasons for the typical defects of the beam blank. A two-dimensional transient coupled finite element model has been developed to compute the temperature and stress profile in beam blank continuous casting. The enthalpy method was used in the heat conduction equation. The thermo-mechanical property in the mushy zone was taken into consideration in this calculation. It is shown that at the mold exit the thickness of the shell had its maximum value at the flange tip and its minimum value at the fillet. The temperature had a great fluctuation on the surface of the beam blank in the secondary cooling zone. At the unbending point, the surface temperature of the web was in the brittleness temperature range under the present condition. To ensure the quality, it is necessary to weaken the intensity of secondary cooling. At the mold exit the equivalent stress and strain have higher values at the flange tip and at the web. From the spray 1 to the unbending point, the maximum values of stress and strain gradually moved to the internal section of the flange tip and the web. However, whenever, there were bigger stress and strain values near the flange tip and the web than in the other parts, it must be very easy to generate cracks at those positions. Now, online verification of this simulation has been developed, which has proved to be very useful and efficient to instruct the practical production of beam blank continuous casting.
基金Project(2008WK2005) supported by the Science and Technology Plan of Hunan Province, China
文摘The effects of low temperature thermo-mechanical treatment （LTTMT） on microstructures and mechanical properties of Ti-6Al-4V （TC4） alloy were studied by optical microscopy （OM）, tensile test, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results confirm that the strength of TC4 alloy can be improved obviously by LTTMT processing, which combines strain strengthening with aging strengthening. The effect of LTTMT on the alloy depends on the microstructure of the refined and dispersed a＋fl phase on the basis of high dislocation density by pre-deformation below recrystallization temperature. The tensile strength decreases with the increase of pre-deformation reduction. The optimal processing parameters of LTTMT for TC4 alloy are as follows： solution treatment at 900 ℃ for 15 min, pre-deformation in the range of 600-700 ℃ with a reduction of 35%, finally aging at 540 ℃ for 4 h followed by air-cooling.
基金This work was supported by Hong Kong ITF research project (No. ITS 098/02).
文摘SMPU （shape memory polyurethane） non-ionomers and ionomers, synthesized with poly（c-caprolactone） （PCL）, 4, 4＇-diphenylmethane diisocyanate （MDI）, 1,4-butanediol （BDO）, dimethylolpropionic acid （DMPA） were measured with cyclic tensile test and strain recovery test. The relations between the structure and shape memory effect of these two series were studied with respect to the ionic group content and the effect of neutralization. The resulting data indicate that, with the introduction of asymmetrical extender, the stress at 100% elongation is decreased for PU non-ionomer and ionomer series, especially lowered sharply for non-ionomer series; the fixation ratio of ionomer series is not affected obviously by the ionic group content; the total recovery ratio of ionomer series is decreased greatly. After sufficient relaxation time for samples stretched beforehand, the switching temperature is raised slightly, whereas the recovery ratio measured with strain recovery test method is lowered with increased DMPA content. The characterization with FT-IR, DSC, DMA elucidated that, the ordered hard domain of the two series is disrupted with the introduction of DMPA which causes more hard segments to dissolve in soft phase; ionic groups on hard segment enhance the cohesion between hard segments especially at high ionic group content and significantly facilitate the phase separation compared with the corresponding non-ionomer at moderate ionic group content.
文摘The objective of this study is to seek solutions to reduce the impact of buildings on climate change and to promote the use of local bio-sourced or geo-sourced materials for sustainable construction. Different samples of raw earth from 3 sites were taken in the commune of Mlomp. Geotechnical tests showed that the raw earth samples from sites 2 and 3 have more clay fraction while site 1 contains more sand. The fact of integrating fibers from crushed palm leaves (Borassus aethiopum) (2%, 4% and 6%) into the 3 raw earth samples reduced the mechanical resistance to compression and traction of the 3 raw earths. The experimental results of thermal tests on samples of earth mixtures with crushed Palma leaf fibers show a decrease in thermal conductivity as well as thermal effusivity as the percentages increase (2%, 4% and 6%) of fibers in raw earth for the 3 sites. This shows that this renewable composite material can help improve the thermal insulation of building envelopes.
基金supported by National Science Foundation for Distinguished Young Scholars of China (Grant No. 50825504)United Fund of National Natural Science Foundation of China and Guangdong Province (Grant No. U0934004)+1 种基金National Hi-tech Research and Development Program of National China (863 Program, Grant No. 2009AA04Z204)Fundamental Research Funds for the Central Universities (Grant No. D2102380)
文摘The material characteristics of a structure will change with temperature variation,and will induce stress within the structure.Currently,the optimal design for the topology of compliant mechanisms is mainly performed in single physical field.However,when compliant mechanisms work in high temperature environments,their displacement outputs are generated not only by mechanical load,but also by the temperature variation which may become the prominent factor.Therefore,the influence of temperature must be considered in the design.In this paper,a novel optimization method for multi-objective topology of thermo-mechanical compliant mechanisms is presented.First,the thermal field is analyzed with finite-element method,where the thermal strain is taken into account in the constitutive relation,and the equivalent nodal thermal load is derived with the principle of virtual work.Then the thermal load is converted into physical loads in elastic field,and the control equation of the thermo-mechanical compliant mechanism is obtained.Second,the mathematical model of the multi-objective topology optimization is built by incorporating both the flexibility and stiffness.Meanwhile,the coupling sensitivity function and the sensitivity analysis equations of thermal steady-state response are derived.Finally,optimality criteria algorithm is employed to obtain numerical solution of the multi-objective topology optimization.Numerical examples show that the compliant mechanisms have better performance and are more applicable if the temperature effect is taken into account in the design process.The presented modeling and analysis methods provide a new idea and an effective approach to topology optimization of compliant mechanisms in electrothermic coupling field and multiphysics fields.
文摘Gleeble1500 thermo-mechanical simulation machine is considered to be the first grade equipment in materials' research. However, it is seldom used in superplastic research. Perhaps this is because its specimen's heating method is not suitable to get large elongation. Elongation is an important parameter to evaluate superplasticity, but some other parameters such as the relationship between stress and strain rate are more important than elongation-it is an essential property to superplasticity. The stress-strain rate relationship can be very easily and very accu- rately got with Gleeble machine than with some other simlar equipment, and the relationship between microstructure and superplastic deformation is more easily examined with Gleeble. Present authors have got some new achievement in anisotropy, heterogeneity of superplastic deformation, and first put forward the regulation of dynamic equilibrium in microstructural evolution during superplastic deformation. All of these have been concluded from the experimental results mainly through Gleeble as well as the microstructural examination.The research work has got the support of National Natural Science Foundation and some international cooperation. Some theoretic and experimental results have been used in the practice of superplastic forming. Obvious effect of reducing cost and improving quality of formed parts has been achieved.
基金conducted within the context of the international DECOVALEX–2011 Project(DEmonstration of COupled models and their VALidation against EXperiments)POSIVA (Finnish Nuclear Waste Management Company) who supported the workSwedish Nuclear Fuel and Waste Manage-ment Co. (SKB), Sweden
文摘The Aspoe Pillar Stability Experiment （APSE） was conducted to study the rock mass response in a heated rock pillar between two large boreholes. This paper summarizes the back calculations of the APSE using a two-dimensional （2D） fracture propagation code FRACOD. To be able to model all the loading phases of the APSE, including the thermal loading, the code was improved in several ways. A sequential excavation function was developed to model promptly the stepwise changing loading geometry. Prior to the mod- elling, short-term compressive strength test models were set up aiming to reproduce the stress-strain behaviour observed for the Aspoe diorite in laboratory. These models simulate both the axial and lateral strains of radial-controlled laboratory tests, The volumetric strain was calculated from the simulations and compared with the laboratory results, The pillar models include vertical and horizontal 2D models from where the stress in the pillar wall was investigated, The vertical model assesses the stability of the experimental rock volume and suggests the resultant stress below the tunnel floor in the pillar area. The horizontal model considers cross-sections of the pillar between the two large boreholes. The horizon- tal model is used to simulate the evolution of the stress in the rock mass during the excavation of the boreholes and during and the heating phase to give an estimation of the spalling strength. The modelling results suggest that the excavation-induced stresses will cause slight fracturing in the pillar walls, if the strength of the APSE pillar is set to about 123 MPa. Fracture propagation driven by thermal loading leads to minor spalling. The thermal evolution, elastic behaviour and brittle failure observed in the experiment are well reflected by the models.
基金supported by Natural Science Research Project of Anhui Province of China (KJ2016A091)Natural Science Foundation of Anhui Province (1708085ME116)Science and Technology Research Program of Anhui Province of China (1201a0201005)
文摘Effects of micro-alloying elements and production process on microstructure, mechanical properties and precipitates of 600 MPa grade rebars were studied by using pilot test, metallographic observa- tion, tensile test, thermodynamic calculation and transmission electron microscopy. The results show that the tested steels are composed of ferrite and pearlite, in which the conterlt range of pearlite is 33%-45%. For vanadium micro-alloyed steel, interphase preeipitation Strengthening effect of V can be promoted and the yield strength of tested steels can be increased with increasing V content and de- creasing finishing rolling temperature. The temperature of terminated cooling should be more than 700 ℃ when the water cooling is used. When niobium is added to the steel, more coarse （Nb,V）C,N precipitates are generated at high temperature, so that the solid solubility of precipitated phases of vanadium is reduced and the precipitation strengthening effect of vanadium is weakened.
基金Project(2012CB619501)supported by the National Basic Research Program of China
文摘The effects of T916 thermo-mechanical process on microstructures, mechanical properties and ballistic resistance of 2519A aluminum alloy were investigated by optical microscopy （OM）, transmission electron microscopy （TEM）, tensile tests and ballistic resistance test. After T916 treatment, the yield strength, tensile strength and elongation rate of 2519A aluminum alloy reach 501 MPa, 540 MPa and 14%, respectively. And the ballistic limit velocity of 2519A-T916 alloy （30 mm in thickness） is 715 rn/s. The microstructure varies near the sidewalls of crater. The interrupted ageing contributes to these excellent properties of the alloy. During T916 process, the precipitation of Guinier Preston （GP） zone is finer and denser during the interrupted ageing, thus resulting in well precipitated strengthening phase.
文摘Three friction welding processes are compared for temperature, stresses and strains, as well as strain rates developed in the early phases of the processes, which are essential in their successful development. These are friction stir welding （FSW）, linear friction welding （LFW） and rotary friction welding （RFW）. Their common characteristic is the use of friction to generate adequate energy and raise temperature locally in order to create favorable conditions for welding at the interface between two parts. Although the mode of movement is different for each one of them, welds are produced through plastic deformation. The Lagrangian and coupled Eulerian-Lagrangian numer- ical models developed have produced results which are in qualitative agreement with experiments and have shed a light on the commonalities of these friction welding processes
文摘Systematic physical simulation of thermo-mechanical processing routes has been ap-plied on a Gleeble 1500 simulator to four copper alloys (mass %) Cu-0.57Co-0.32Si,Cu-0.55Cr-0.065P, Cu-0.22Zr-0.035Si and Cu-1.01Ni-0.43Si aimed at clarifying theinfluences of processing conditions on their final properties, strength and electricalconductivity. Flow curves were determined over wide temperature and strain rateranges. Hardness was used as a measure of the strength level achieved. High hard-ness was obtained as using equal amounts (strains 0.5) of cold deformation beforeand after the precipitation annealing stage. The maximum values achieved for theCu-Co-Si, Cu-Cr-P, Cu-Zr-Si and Cu-Ni-Si alloys were 190, 165, 178 and 193 HV5,respectively. A thermo-mechanical schedule involving the hot deformation-ageing-colddeformation stages showed even better results for the Cu-Zr-Si alloy. Consequently,the processing routes were designed based on simulation test results and wires of 5 and2mm in diameters have been successfully processed in the industrial scale.
