Recent observations by electron microscopy have shown that a dislocation-free zone (DFZ) exists between the crack tip and the pile-up of dislocations in the plastic zone. Shang, S. J., Ohr, S. M. and Majumdar, B. S., ...Recent observations by electron microscopy have shown that a dislocation-free zone (DFZ) exists between the crack tip and the pile-up of dislocations in the plastic zone. Shang, S. J., Ohr, S. M. and Majumdar, B. S., Burns, S. J. have discussed the problem of the plastic zone at a crack tip in isotropic elastic medium. We know that the hard second phase, which neither causes very large stress concentration nor leads to micrographic split, can improve the bearing capacity of the materials. Therefore, it is necessary to discuss the problem of the plastic zone at a crack tip while the hard second phase exists.展开更多
Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel T...Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.展开更多
In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing...In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing was conducted on a Gleeble-1500 thermo-mechanical simulator.The mean grain size Dg of each annealed specimen was measured by the quantitative metallography technique.The grain growth kinetics of the Mg-6Zn alloy annealed at 473-623 K was obtained as Dg^4- Dg0^4=2.25 ×10^11 exp（-95450）by the least square linear regression method.The deviation of grain growth exponent n = 4 from the theoretical value of 2 may be attributed to the presence of solute zinc and second phases which will retard the boundary migration.Microscopic observations show that the non-uniform distribution of grain size for samples pre-extruded or annealed at low temperatures is closely related to the non-uniform distribution of fine and dispersed second phases but not to the non-uniform distribution of solute zinc.This indicates that second phase pinning effect plays an important role in microstructure refinement.展开更多
基金National Natural Science Foundation of China(51701079)Doctoral Scientific Research Start-up Foundation from Huaiyin Institute of Technology,Jiangsu,China(Z301B18558)Enterprise-University-Research Institute Collaboration Project of Jiangsu Province(FZ20190349)。
文摘Recent observations by electron microscopy have shown that a dislocation-free zone (DFZ) exists between the crack tip and the pile-up of dislocations in the plastic zone. Shang, S. J., Ohr, S. M. and Majumdar, B. S., Burns, S. J. have discussed the problem of the plastic zone at a crack tip in isotropic elastic medium. We know that the hard second phase, which neither causes very large stress concentration nor leads to micrographic split, can improve the bearing capacity of the materials. Therefore, it is necessary to discuss the problem of the plastic zone at a crack tip while the hard second phase exists.
基金Item Sponsored by National Key Technology Research and Development Program in 11th Five-Year Plan of China (2006BE03A0)
文摘Two types of stress relaxation tests were carried out to investigate the incubation time for incipient precipi-tation of Ti（C,N） in deformed austenite and （Ti,Mo）C in ferrite of ferritic Ti-Mo microalloyed steel The size dis-tribution, amount and chemical composition of precipitates were obtained by using physicochemical phase analysis, and calculated according to thermodynamics and kinetics. The experimental results demonstrated that the incubation time was reduced with increasing Ti content, and prolonged with the addition of Mo. After 30 % deformation at 850 ℃, the nucleation of strain-induced Ti（C,N） was a relatively slow process. On the other hand, the temperature where the nucleation rate of （Ti, Mo）C in ferrite was the highest descended first and then ascended with increasing Ti content, and so did the temperature where the incubation time was the shortest. The key point is that the tempera-ture of steel containing about 0.09 % Ti is the lowest. The mass fraction of MC-type particles with size smaller than 10 nm in steel containing 0.09% Ti and 0.2% Mo reached 73.7%. The size distributions of precipitates in steel containing 0.09% Ti were relatively concentrated compared with that in steel containing 0.07% Ti.
基金the financial support from the National Natural Science Foundation of China(Grant No.51105328)the Natural Science Foundation of Jiangsu Province of China(No.BK20130447)the Colleges and Universities in Jiangsu Province Natural Science Foundation of China(Grant No.13KJB430026)
文摘In order to control the grain size during hot forming,grain growth behavior of a pre-extruded Mg-6Zn magnesium alloy and its correlation with solute and second phase distribution were investigated.Isothermal annealing was conducted on a Gleeble-1500 thermo-mechanical simulator.The mean grain size Dg of each annealed specimen was measured by the quantitative metallography technique.The grain growth kinetics of the Mg-6Zn alloy annealed at 473-623 K was obtained as Dg^4- Dg0^4=2.25 ×10^11 exp（-95450）by the least square linear regression method.The deviation of grain growth exponent n = 4 from the theoretical value of 2 may be attributed to the presence of solute zinc and second phases which will retard the boundary migration.Microscopic observations show that the non-uniform distribution of grain size for samples pre-extruded or annealed at low temperatures is closely related to the non-uniform distribution of fine and dispersed second phases but not to the non-uniform distribution of solute zinc.This indicates that second phase pinning effect plays an important role in microstructure refinement.
