This contribution attempts to model the alteration of the in-plane elastic properties in laminates caused by stitching, and to predict the in-plane effective tensile strength of the stitched composite laminates. The d...This contribution attempts to model the alteration of the in-plane elastic properties in laminates caused by stitching, and to predict the in-plane effective tensile strength of the stitched composite laminates. The distortion of in-plane fibers is considered to be the main cause that affects the in-plane mechanical properties. A fiber distortion model is proposed to characterize the fiber misalignment and the fiber content concentration due to stitching. The undistorted region, the fiber distortion region, the resin-rich pocket and the through-thickness reinforcement section are taken into account. The fiber misalignment and inhomogeneous fiber content due to stitching have been formulated by introducing two parameters, the distortion width and maximum misalignment. It has been found that the ply stress concentration in stitched laminates is influenced by the two concurrent factors, the stitch hole and inhomogeneous fiber content. The stitch hole brings about the stress concentration whereas the higher fiber content at the local region induced by stitching restrains the local deformation of the composite. The model is used to predict the tensile strength of the [0/45/0/-45/90/45/0/-45]58 T300/QY9512 composite laminate stitched by Kevlar 29 yarn with different stitching configurations, showing an acceptable agreement with experimental data.展开更多
Blended-Wing-Body(BWB)aircraft is promoted as one of the most possible layouts to achieve more sustainable civil aviation.Due to the non-circular cross-section of the center-body,a bulge deformation forms over the upp...Blended-Wing-Body(BWB)aircraft is promoted as one of the most possible layouts to achieve more sustainable civil aviation.Due to the non-circular cross-section of the center-body,a bulge deformation forms over the upper surface of the body under the coupled loads of the internal pressurization of the cabin and the aerodynamic bending moments of the wing,which reduces the lift-to-drag ratio of BWB aircraft.Under a limited deformation,the relationship between the aerodynamic performance and the structural weight needs to be studied.In this work,the effects of stiffness constraints on the center-body deformation,structural weight of the airframe and aerodynamic performance were investigated by using an analytical model of the Pultruded Rod Stitched Efficient Unitized Structure(PRSEUS)for the airframe and the computational fluid dynamics method,respectively.The results show that as the stiffness constraint increases,the spacings between the rod stringers and the frame stiffeners decrease,and the structural weight increases inversely.A 5.2% reduction of the lift-to-drag ratio is encountered at cruise for a medium deformation design of 42.8 mm/m.A higher aerodynamic penalty is suffered when the stiffness constraint is further released.The final deformation criterion is different when the weight vector of the aerodynamic performance and structural weight is different.展开更多
A representative volume element method and a novel mesomechanical-based polyline model are proposed to describe the misalignment of in-plane fibers induced by the insertion of stitch thread.A multi-scale mathematical ...A representative volume element method and a novel mesomechanical-based polyline model are proposed to describe the misalignment of in-plane fibers induced by the insertion of stitch thread.A multi-scale mathematical model of in-plane elastic parameters for stitched composite laminate is established with ply-angle and stitch parameters as well as material parameters taken into account.Based on the fabrication of specimens and the verification of experimental platform,the superposition influences of stitch on structural anisotropy are revealed by the developed theoretical model.Results indicate that the stitch orientation can increase the structural anisotropy.The decreases of stitch pitch and spacing as well as the increase of thread diameter obviously reduce the elastic and shear moduli of laminates.Furthermore,the elastic and shear moduli as well as Poisson’s ratios show sinusoidal changes with a period of 90°as the ply-angle increases.The theoretical model not only analyzes the in-plane mechanical properties of stitched laminate with ply-angle,but also lays a foundation for the dynamic studies of stitched sandwich structures with ribs in the future.展开更多
This paper presents an application of stitched ground plane for microstrip patch antenna design. In this work Matlab interface to computer embroidery techniques were used to implement the felt and denim substrates on ...This paper presents an application of stitched ground plane for microstrip patch antenna design. In this work Matlab interface to computer embroidery techniques were used to implement the felt and denim substrates on microstrip patch antenna. These antennas were simulated using a commercial full 3D electromagnetic CST Microwave Studio 2019. A method to optimize the stitch patterns with conductive thread for antenna ground plane for 2.45 GHz industrial, scientific, and medical (ISM) band and 5 GHz wearable wireless local area networks (WLAN) frequencies was achieved. Rigid and flexible wearable antennas (microstrip patch antennas) were fabricated using the stitched ground plane. The electrical resistance was reduced between the meshes during the stitching design process. Results in terms of bandwidth, radiation patterns and reflection coefficients (S<sub>11</sub>) are presented.展开更多
This work explores the optimal mesh structure, stitch density and production technique of stitched ground plane for microstrip patch antenna. Meshed ground plane was used as a generic problem. A stitched ground plane ...This work explores the optimal mesh structure, stitch density and production technique of stitched ground plane for microstrip patch antenna. Meshed ground plane was used as a generic problem. A stitched ground plane is pro-posed and designed using Matlab interface to computer embroidery. Using the meshed or stitched ground plane as a case study, the resistance between meshes was analysed and measured. The equivalent resistance between nodes is a function of their distance apart. A finite resistive grid was simulated and compared to measured sets of data. A microstrip patch antenna with stitched ground shows comparable performance to the conventional etched ground of the size in terms of bandwidth. The stitched ground plane has a higher band-width than the etched copper ground plane because of the increased thickness of the substrate. Thus, it can be concluded that the use of the interface method shows the possibilities of controlling the stitch density and distances between mesh nodes. The interface increases the stitching density and reduces the elec-trical resistance between mesh nodes making the antennas flexible and weara-ble. The functionality of these antenna samples has been tested and validated using microstrip patch ground at 2.45 GHz and 5 GHz. Measurement results on the proposed stitched ground planes were compared with the theory of infinite resistive network that shows good agreement.展开更多
The mechanical properties of silica material in the monolithic form are ;far from acceptable levels. In this paper, 3D stitched quartz preform was used for the fiber reinforcement, and quartz fibers- reinforced silica...The mechanical properties of silica material in the monolithic form are ;far from acceptable levels. In this paper, 3D stitched quartz preform was used for the fiber reinforcement, and quartz fibers- reinforced silica composites were prepared by the silica sol-infiltration-sintering method. The density of the composite was up to 1.71 g/cm3 after 10 infiltration-sintering cycles. The flexural strength and the in-plane shear strength were 61.7 MPa and 20.3 MPa, respectively. The flexural stress-deflection curve exhibited mostly nonlinear behavior, which was different from that of monolithic ceramics. Because of the existence of the fiber in Z axis direction, shearing property between the different layers of 3D stitched composites were greatly enhanced. Toughness effect of the 3D stitched quartz preform was conspicuous. The as-fabricated composites showed non-catastronhic failure behavior resulting from weak fiber/matrix interface.展开更多
In this paper, by constructing the one-to-one correspondence between its IFS and the quaternary fractional expansion, the n-th iteration analytical expression and the limit representation of the family of the Koch-typ...In this paper, by constructing the one-to-one correspondence between its IFS and the quaternary fractional expansion, the n-th iteration analytical expression and the limit representation of the family of the Koch-type curves with arbitrary angles are obtained. The distinction between our method and that of H. Sagan is that we provide the generation process analytically and represent it as a graph of a series function which looks like the Weierstrass function. With these arithmetic expressions, we further analyze and prove some of the fractal properties of the Koch-type curves such as the self-similarity, the HSlder exponent and with the property of continuous everywhere but differentiable nowhere. Then, we will show that the Koch- type curves can be approximated by different constructed generators. Based on the analytic transformation of the Koch-type curves, we also constructed more continuous but nowhere-differentiable curves represented by arithmetic expressions. This result implies that the analytical expression of a fractal has theoretical and practical significance.展开更多
Crack growth resistance plays a different role in crashworthiness analysis since the progressive energy absorption is based on controllable fracture mechanisms. In this regard, the present paper studies the efficient ...Crack growth resistance plays a different role in crashworthiness analysis since the progressive energy absorption is based on controllable fracture mechanisms. In this regard, the present paper studies the efficient crack growth resistance in off-axis crushing of composite tubular structures by implementing natural fiber yarns. One of the through-to-thickness reinforcement methods known as stitching has been chosen to influence the axial and off-axis crushing process. Improving the crack growth resistance and appropriate fiber breakage at different stages of crushing process can significantly improve the resistance force and consequently the energy absorption capability of composite absorbers in axial and off-axis crushing. This analysis will be applied to non-stitched and stitched CFRP composite boxes which showed brittle fracture and transverse shearing crushing modes under off-axis loading of 10 degrees. The analytical methods are also implemented to analysze the effect of various failure mechanisms such as bending, friction, bundle fracture, and interlaminar crack growth for the observed crushing modes. The proposed model is able to predict the crushing load and crush force efficiency in close agreement from experimental studies.展开更多
The recent advancements in the field of Virtual Reality(VR)and Augmented Reality(AR)have a substantial impact on modern day technology by digitizing each and everything related to human life and open the doors to the ...The recent advancements in the field of Virtual Reality(VR)and Augmented Reality(AR)have a substantial impact on modern day technology by digitizing each and everything related to human life and open the doors to the next generation Software Technology(Soft Tech).VR and AR technology provide astonishing immersive contents with the help of high quality stitched panoramic contents and 360°imagery that widely used in the education,gaming,entertainment,and production sector.The immersive quality of VR and AR contents are greatly dependent on the perceptual quality of panoramic or 360°images,in fact a minor visual distortion can significantly degrade the overall quality.Thus,to ensure the quality of constructed panoramic contents for VR and AR applications,numerous Stitched Image Quality Assessment(SIQA)methods have been proposed to assess the quality of panoramic contents before using in VR and AR.In this survey,we provide a detailed overview of the SIQA literature and exclusively focus on objective SIQA methods presented till date.For better understanding,the objective SIQA methods are classified into two classes namely Full-Reference SIQA and No-Reference SIQA approaches.Each class is further categorized into traditional and deep learning-based methods and examined their performance for SIQA task.Further,we shortlist the publicly available benchmark SIQA datasets and evaluation metrices used for quality assessment of panoramic contents.In last,we highlight the current challenges in this area based on the existing SIQA methods and suggest future research directions that need to be target for further improvement in SIQA domain.展开更多
Stitched composite materials are emerging as a promising material due to their high interlaminar strength,combined performance and light weight.The mechanical properties of stitch yarns are very essential for stitched...Stitched composite materials are emerging as a promising material due to their high interlaminar strength,combined performance and light weight.The mechanical properties of stitch yarns are very essential for stitched composite structures.In this study,the tensile behaviors of the twisted fiber yarn in stitched composites were investigated experimentally,analytically and numerically.Two kinds of cross-sectional area of twisted yarn are proposed and discussed.The paper presents an intersecting circle model to describe the cross-section of twisted fiber yarns,and a physics-based theoretical model to predict the effective tensile moduli.The numerical models take into account the cross-sectional characteristic and the twist architecture.The investigation shows that:the sum of each fiber area should be used for experimental analysis;and the crosssectional area surrounded by the yarn profile should be used for theoretical predictions and finite element(FE)simulations.The relative errors of the prediction method and the FE simulation are less than 2%and 1%,respectively.The friction between the fibers is derived,and the effect of friction on mechanical properties is discussed.The investigation method will serve as a fundamental component of twisted fiber bundle/yarn analysis.展开更多
This work reveals that the addition of periodically distributed stitches to sandwich structure enables a significant reduction of vibration in stop-band and this new functionality is systematically investigated.Firstl...This work reveals that the addition of periodically distributed stitches to sandwich structure enables a significant reduction of vibration in stop-band and this new functionality is systematically investigated.Firstly,a finite element model which is capable of taking into consideration the three layers of the sandwich as well as the stitches is developed.The diagram of dispersion is calculated by applying Floquet-Bloch theorem to the boundaries of unit cell.With properly chosen properties of stitches,a stop-band for flexural wave is observed.This stop-band is further confirmed by the forced response of a large stitched sandwich panel under point excitation.The level of vibration in the stop-band is significantly reduced.The influence of the stitch rigidity and density on upper and lower limits of stop-band is also examined,which confirms that stitched sandwich can be tuned to mitigate vibration in a certain frequency band with appropriate stitch properties.These investigations have demonstrated the potential application of stitched sandwich in the area of vibration reduction.展开更多
基金Project supported by the Excellent Young Teachers Program of the Ministry of Education of Chinathe Shu-Guang Program of the City of Shanghai+1 种基金the National Natural Sciences Foundation of China(No.10372120)Shanghai Leading Academic Discipline Project(No.Y0103).
文摘This contribution attempts to model the alteration of the in-plane elastic properties in laminates caused by stitching, and to predict the in-plane effective tensile strength of the stitched composite laminates. The distortion of in-plane fibers is considered to be the main cause that affects the in-plane mechanical properties. A fiber distortion model is proposed to characterize the fiber misalignment and the fiber content concentration due to stitching. The undistorted region, the fiber distortion region, the resin-rich pocket and the through-thickness reinforcement section are taken into account. The fiber misalignment and inhomogeneous fiber content due to stitching have been formulated by introducing two parameters, the distortion width and maximum misalignment. It has been found that the ply stress concentration in stitched laminates is influenced by the two concurrent factors, the stitch hole and inhomogeneous fiber content. The stitch hole brings about the stress concentration whereas the higher fiber content at the local region induced by stitching restrains the local deformation of the composite. The model is used to predict the tensile strength of the [0/45/0/-45/90/45/0/-45]58 T300/QY9512 composite laminate stitched by Kevlar 29 yarn with different stitching configurations, showing an acceptable agreement with experimental data.
基金supported partially by the National Key Laboratory Project,China(No.61422010201).
文摘Blended-Wing-Body(BWB)aircraft is promoted as one of the most possible layouts to achieve more sustainable civil aviation.Due to the non-circular cross-section of the center-body,a bulge deformation forms over the upper surface of the body under the coupled loads of the internal pressurization of the cabin and the aerodynamic bending moments of the wing,which reduces the lift-to-drag ratio of BWB aircraft.Under a limited deformation,the relationship between the aerodynamic performance and the structural weight needs to be studied.In this work,the effects of stiffness constraints on the center-body deformation,structural weight of the airframe and aerodynamic performance were investigated by using an analytical model of the Pultruded Rod Stitched Efficient Unitized Structure(PRSEUS)for the airframe and the computational fluid dynamics method,respectively.The results show that as the stiffness constraint increases,the spacings between the rod stringers and the frame stiffeners decrease,and the structural weight increases inversely.A 5.2% reduction of the lift-to-drag ratio is encountered at cruise for a medium deformation design of 42.8 mm/m.A higher aerodynamic penalty is suffered when the stiffness constraint is further released.The final deformation criterion is different when the weight vector of the aerodynamic performance and structural weight is different.
基金National Natural Science Foundation of China(No.52075280)Natural Science Foundation of Shandong province(No.ZR2019MEE088)。
文摘A representative volume element method and a novel mesomechanical-based polyline model are proposed to describe the misalignment of in-plane fibers induced by the insertion of stitch thread.A multi-scale mathematical model of in-plane elastic parameters for stitched composite laminate is established with ply-angle and stitch parameters as well as material parameters taken into account.Based on the fabrication of specimens and the verification of experimental platform,the superposition influences of stitch on structural anisotropy are revealed by the developed theoretical model.Results indicate that the stitch orientation can increase the structural anisotropy.The decreases of stitch pitch and spacing as well as the increase of thread diameter obviously reduce the elastic and shear moduli of laminates.Furthermore,the elastic and shear moduli as well as Poisson’s ratios show sinusoidal changes with a period of 90°as the ply-angle increases.The theoretical model not only analyzes the in-plane mechanical properties of stitched laminate with ply-angle,but also lays a foundation for the dynamic studies of stitched sandwich structures with ribs in the future.
文摘This paper presents an application of stitched ground plane for microstrip patch antenna design. In this work Matlab interface to computer embroidery techniques were used to implement the felt and denim substrates on microstrip patch antenna. These antennas were simulated using a commercial full 3D electromagnetic CST Microwave Studio 2019. A method to optimize the stitch patterns with conductive thread for antenna ground plane for 2.45 GHz industrial, scientific, and medical (ISM) band and 5 GHz wearable wireless local area networks (WLAN) frequencies was achieved. Rigid and flexible wearable antennas (microstrip patch antennas) were fabricated using the stitched ground plane. The electrical resistance was reduced between the meshes during the stitching design process. Results in terms of bandwidth, radiation patterns and reflection coefficients (S<sub>11</sub>) are presented.
文摘This work explores the optimal mesh structure, stitch density and production technique of stitched ground plane for microstrip patch antenna. Meshed ground plane was used as a generic problem. A stitched ground plane is pro-posed and designed using Matlab interface to computer embroidery. Using the meshed or stitched ground plane as a case study, the resistance between meshes was analysed and measured. The equivalent resistance between nodes is a function of their distance apart. A finite resistive grid was simulated and compared to measured sets of data. A microstrip patch antenna with stitched ground shows comparable performance to the conventional etched ground of the size in terms of bandwidth. The stitched ground plane has a higher band-width than the etched copper ground plane because of the increased thickness of the substrate. Thus, it can be concluded that the use of the interface method shows the possibilities of controlling the stitch density and distances between mesh nodes. The interface increases the stitching density and reduces the elec-trical resistance between mesh nodes making the antennas flexible and weara-ble. The functionality of these antenna samples has been tested and validated using microstrip patch ground at 2.45 GHz and 5 GHz. Measurement results on the proposed stitched ground planes were compared with the theory of infinite resistive network that shows good agreement.
文摘The mechanical properties of silica material in the monolithic form are ;far from acceptable levels. In this paper, 3D stitched quartz preform was used for the fiber reinforcement, and quartz fibers- reinforced silica composites were prepared by the silica sol-infiltration-sintering method. The density of the composite was up to 1.71 g/cm3 after 10 infiltration-sintering cycles. The flexural strength and the in-plane shear strength were 61.7 MPa and 20.3 MPa, respectively. The flexural stress-deflection curve exhibited mostly nonlinear behavior, which was different from that of monolithic ceramics. Because of the existence of the fiber in Z axis direction, shearing property between the different layers of 3D stitched composites were greatly enhanced. Toughness effect of the 3D stitched quartz preform was conspicuous. The as-fabricated composites showed non-catastronhic failure behavior resulting from weak fiber/matrix interface.
基金Supported partly by National Natural Science Foundation of China(No.60962009)
文摘In this paper, by constructing the one-to-one correspondence between its IFS and the quaternary fractional expansion, the n-th iteration analytical expression and the limit representation of the family of the Koch-type curves with arbitrary angles are obtained. The distinction between our method and that of H. Sagan is that we provide the generation process analytically and represent it as a graph of a series function which looks like the Weierstrass function. With these arithmetic expressions, we further analyze and prove some of the fractal properties of the Koch-type curves such as the self-similarity, the HSlder exponent and with the property of continuous everywhere but differentiable nowhere. Then, we will show that the Koch- type curves can be approximated by different constructed generators. Based on the analytic transformation of the Koch-type curves, we also constructed more continuous but nowhere-differentiable curves represented by arithmetic expressions. This result implies that the analytical expression of a fractal has theoretical and practical significance.
文摘Crack growth resistance plays a different role in crashworthiness analysis since the progressive energy absorption is based on controllable fracture mechanisms. In this regard, the present paper studies the efficient crack growth resistance in off-axis crushing of composite tubular structures by implementing natural fiber yarns. One of the through-to-thickness reinforcement methods known as stitching has been chosen to influence the axial and off-axis crushing process. Improving the crack growth resistance and appropriate fiber breakage at different stages of crushing process can significantly improve the resistance force and consequently the energy absorption capability of composite absorbers in axial and off-axis crushing. This analysis will be applied to non-stitched and stitched CFRP composite boxes which showed brittle fracture and transverse shearing crushing modes under off-axis loading of 10 degrees. The analytical methods are also implemented to analysze the effect of various failure mechanisms such as bending, friction, bundle fracture, and interlaminar crack growth for the observed crushing modes. The proposed model is able to predict the crushing load and crush force efficiency in close agreement from experimental studies.
文摘The recent advancements in the field of Virtual Reality(VR)and Augmented Reality(AR)have a substantial impact on modern day technology by digitizing each and everything related to human life and open the doors to the next generation Software Technology(Soft Tech).VR and AR technology provide astonishing immersive contents with the help of high quality stitched panoramic contents and 360°imagery that widely used in the education,gaming,entertainment,and production sector.The immersive quality of VR and AR contents are greatly dependent on the perceptual quality of panoramic or 360°images,in fact a minor visual distortion can significantly degrade the overall quality.Thus,to ensure the quality of constructed panoramic contents for VR and AR applications,numerous Stitched Image Quality Assessment(SIQA)methods have been proposed to assess the quality of panoramic contents before using in VR and AR.In this survey,we provide a detailed overview of the SIQA literature and exclusively focus on objective SIQA methods presented till date.For better understanding,the objective SIQA methods are classified into two classes namely Full-Reference SIQA and No-Reference SIQA approaches.Each class is further categorized into traditional and deep learning-based methods and examined their performance for SIQA task.Further,we shortlist the publicly available benchmark SIQA datasets and evaluation metrices used for quality assessment of panoramic contents.In last,we highlight the current challenges in this area based on the existing SIQA methods and suggest future research directions that need to be target for further improvement in SIQA domain.
基金co-supported by the National Natural Science Foundation of China(Nos.51772009,51911530201,51802264 and 51275023)。
文摘Stitched composite materials are emerging as a promising material due to their high interlaminar strength,combined performance and light weight.The mechanical properties of stitch yarns are very essential for stitched composite structures.In this study,the tensile behaviors of the twisted fiber yarn in stitched composites were investigated experimentally,analytically and numerically.Two kinds of cross-sectional area of twisted yarn are proposed and discussed.The paper presents an intersecting circle model to describe the cross-section of twisted fiber yarns,and a physics-based theoretical model to predict the effective tensile moduli.The numerical models take into account the cross-sectional characteristic and the twist architecture.The investigation shows that:the sum of each fiber area should be used for experimental analysis;and the crosssectional area surrounded by the yarn profile should be used for theoretical predictions and finite element(FE)simulations.The relative errors of the prediction method and the FE simulation are less than 2%and 1%,respectively.The friction between the fibers is derived,and the effect of friction on mechanical properties is discussed.The investigation method will serve as a fundamental component of twisted fiber bundle/yarn analysis.
文摘This work reveals that the addition of periodically distributed stitches to sandwich structure enables a significant reduction of vibration in stop-band and this new functionality is systematically investigated.Firstly,a finite element model which is capable of taking into consideration the three layers of the sandwich as well as the stitches is developed.The diagram of dispersion is calculated by applying Floquet-Bloch theorem to the boundaries of unit cell.With properly chosen properties of stitches,a stop-band for flexural wave is observed.This stop-band is further confirmed by the forced response of a large stitched sandwich panel under point excitation.The level of vibration in the stop-band is significantly reduced.The influence of the stitch rigidity and density on upper and lower limits of stop-band is also examined,which confirms that stitched sandwich can be tuned to mitigate vibration in a certain frequency band with appropriate stitch properties.These investigations have demonstrated the potential application of stitched sandwich in the area of vibration reduction.
