The realization way of snake rolling was introduced. Flow velocity, strain and stress distribution of 7075 aluminum alloy plate during snake rolling and symmetrical rolling were analyzed in Deform 3D. Effects of veloc...The realization way of snake rolling was introduced. Flow velocity, strain and stress distribution of 7075 aluminum alloy plate during snake rolling and symmetrical rolling were analyzed in Deform 3D. Effects of velocity ratio, offset distance between two rolls and pass reduction on the distribution of equivalent strain and shear strain were analyzed. The results show that flow velocity and equivalent strain on the lower layer of the plate are larger than those of the upper layer because of the larger velocity of the lower roll and the gap is increased with the increase of velocity ratio and pass reduction. The shear strain of roiling direction in the center point is almost zero during symmetrical rolling, while it is much larger during snake rolling because of the existence of rub zone. The shear strain is increased with the increase of velocity ratio, offset distance and pass reduction. This additional shear strain is beneficial to improve the in_homogeneous strain distribution.展开更多
The microstructure and mechanical properties evolution of AISI 301LN metastable austenitic stainless steels during cold rolling were investigated. A wide range of cold thickness reduction (10%-80%) was carried out in ...The microstructure and mechanical properties evolution of AISI 301LN metastable austenitic stainless steels during cold rolling were investigated. A wide range of cold thickness reduction (10%-80%) was carried out in a four-high rolling mill at ambient temperature. The X-ray and Feritscope MP30 were used to identify the strain-induced α′-martensite phase and its volume fraction, respectively. The microstructure was observed by optical micrograph and the mechanical properties were determined by tensile tests and microhardness. The results show that the strain-induced α′-martensite nucleated at the shear bands intersections and the growth of α′-martensite occurred by the repeated nucleation of new embryos. The volume fraction of strain-induced α′-martensite increased with increasing the cold rolling reduction. In addition, the percentage increased in the tensile strength is the same as that of hardness. The ratio between the average tensile strength and the average microhardness was found to range between 2.82 and 3.17.展开更多
基金Projects(2012CB619505,2010CB731703)supported by the National Basic Research Program of ChinaProject(CX2013B065)supported by Hunan Provincial Innovation Foundation for Postgraduate,ChinaProject(117308)supported by Postdoctoral Science Foundation of Central South University,China
文摘The realization way of snake rolling was introduced. Flow velocity, strain and stress distribution of 7075 aluminum alloy plate during snake rolling and symmetrical rolling were analyzed in Deform 3D. Effects of velocity ratio, offset distance between two rolls and pass reduction on the distribution of equivalent strain and shear strain were analyzed. The results show that flow velocity and equivalent strain on the lower layer of the plate are larger than those of the upper layer because of the larger velocity of the lower roll and the gap is increased with the increase of velocity ratio and pass reduction. The shear strain of roiling direction in the center point is almost zero during symmetrical rolling, while it is much larger during snake rolling because of the existence of rub zone. The shear strain is increased with the increase of velocity ratio, offset distance and pass reduction. This additional shear strain is beneficial to improve the in_homogeneous strain distribution.
基金Item Sponsored by National High-Tech Research and Development Program (863 Program) of China (2008AA030702)
文摘The microstructure and mechanical properties evolution of AISI 301LN metastable austenitic stainless steels during cold rolling were investigated. A wide range of cold thickness reduction (10%-80%) was carried out in a four-high rolling mill at ambient temperature. The X-ray and Feritscope MP30 were used to identify the strain-induced α′-martensite phase and its volume fraction, respectively. The microstructure was observed by optical micrograph and the mechanical properties were determined by tensile tests and microhardness. The results show that the strain-induced α′-martensite nucleated at the shear bands intersections and the growth of α′-martensite occurred by the repeated nucleation of new embryos. The volume fraction of strain-induced α′-martensite increased with increasing the cold rolling reduction. In addition, the percentage increased in the tensile strength is the same as that of hardness. The ratio between the average tensile strength and the average microhardness was found to range between 2.82 and 3.17.
