This paper deals with static pull and push bending tests on two-dimensional （2D） orthogonal EW220/5284 twill weave fabric （TWF） composite tee-joints processed with the resin transfer moulding （RTM） technique. St...This paper deals with static pull and push bending tests on two-dimensional （2D） orthogonal EW220/5284 twill weave fabric （TWF） composite tee-joints processed with the resin transfer moulding （RTM） technique. Static pull and push bending properties are determined and failure initiation mechanism is deduced from experimental observations. The experiments show that the failure initiation load, on average, is greater for push bending than for pull bending, whereas the scatter is smaller for push bending than for pull bending. The failure mode of RTM-made tee-joints in pull bending tests can be reckoned to be characteristic of debonding of resin matrix at the interface between the triangular resin-rich zone and the curved web of tee-joint until complete separation of the curved web from the bottom plate. In contrast, as distinct from the products subject to pull bending loading, the RTM tee-joints in push bending tests experience matrix cracking and fibre fracture from outer layers to inner layers of the bottom plate until catastrophic collapse resulting from the bending. Three-dimensional finite element （FE） models are presented to simulate the load transfer path and failure initiation mechanism of RTM-made TWF composite tee-joint based on the maximum stress criterion. Good correlation between experimental and numerical results is achieved.展开更多
针对某型飞机复合材料扰流板接头,选取典型十字连接区为研究对象,研究4点弯载荷作用下采用树脂传递模塑(Resin transfer moulding,RTM)成型工艺的十字接头典型件的极限承载能力,分析其损伤破坏模式,为复合材料RTM接头的设计强度分析提...针对某型飞机复合材料扰流板接头,选取典型十字连接区为研究对象,研究4点弯载荷作用下采用树脂传递模塑(Resin transfer moulding,RTM)成型工艺的十字接头典型件的极限承载能力,分析其损伤破坏模式,为复合材料RTM接头的设计强度分析提供参考。论文通过典型细节件4点弯曲试验,测量了其极限承载能力,获得了试件典型破坏模式;同时基于商用ABAQUS有限元软件平台,建立了十字连接区典型细节件有限元模型,数值模拟了其损伤破坏过程。通过比较数值模拟结果和试验结果,验证了数值模拟的可行性。展开更多
Biocomposite panels consisting of biobased thermoset resins (EP, PU, UP, and tannin) and flax fibre reinforcements were produced using the vacuum assisted resin transfer moulding process. Panels based on a conventiona...Biocomposite panels consisting of biobased thermoset resins (EP, PU, UP, and tannin) and flax fibre reinforcements were produced using the vacuum assisted resin transfer moulding process. Panels based on a conventional chemical-based resin matrix were also produced, and investigated comparatively. Rheometric analyses were performed to evaluate the suitability of these resins for liquid composite moulding. Tensile, shear, and impactbending tests have been carried out to assess the quality and mechanical performance of manufactured laminates. The impregnation quality was assessed by means of ultrasonic-C-scanning and microscopy. It turned out that the properties of the biobased composite panels made of biobased epoxy resin and a biobased UP-resin from the company Nuplex in New Zealand were onlay slightly inferior to those produced with a conventional epoxy resin. A biobased PU-resin from the company USSC in the USA developed voids during curing. A tannin-based resin containing of formaldehyde was not processable.展开更多
基金National Natural Science Foundation of China (E050603)Aeronautical Science Foundation of China (20095251024)
文摘This paper deals with static pull and push bending tests on two-dimensional （2D） orthogonal EW220/5284 twill weave fabric （TWF） composite tee-joints processed with the resin transfer moulding （RTM） technique. Static pull and push bending properties are determined and failure initiation mechanism is deduced from experimental observations. The experiments show that the failure initiation load, on average, is greater for push bending than for pull bending, whereas the scatter is smaller for push bending than for pull bending. The failure mode of RTM-made tee-joints in pull bending tests can be reckoned to be characteristic of debonding of resin matrix at the interface between the triangular resin-rich zone and the curved web of tee-joint until complete separation of the curved web from the bottom plate. In contrast, as distinct from the products subject to pull bending loading, the RTM tee-joints in push bending tests experience matrix cracking and fibre fracture from outer layers to inner layers of the bottom plate until catastrophic collapse resulting from the bending. Three-dimensional finite element （FE） models are presented to simulate the load transfer path and failure initiation mechanism of RTM-made TWF composite tee-joint based on the maximum stress criterion. Good correlation between experimental and numerical results is achieved.
文摘针对某型飞机复合材料扰流板接头,选取典型十字连接区为研究对象,研究4点弯载荷作用下采用树脂传递模塑(Resin transfer moulding,RTM)成型工艺的十字接头典型件的极限承载能力,分析其损伤破坏模式,为复合材料RTM接头的设计强度分析提供参考。论文通过典型细节件4点弯曲试验,测量了其极限承载能力,获得了试件典型破坏模式;同时基于商用ABAQUS有限元软件平台,建立了十字连接区典型细节件有限元模型,数值模拟了其损伤破坏过程。通过比较数值模拟结果和试验结果,验证了数值模拟的可行性。
文摘Biocomposite panels consisting of biobased thermoset resins (EP, PU, UP, and tannin) and flax fibre reinforcements were produced using the vacuum assisted resin transfer moulding process. Panels based on a conventional chemical-based resin matrix were also produced, and investigated comparatively. Rheometric analyses were performed to evaluate the suitability of these resins for liquid composite moulding. Tensile, shear, and impactbending tests have been carried out to assess the quality and mechanical performance of manufactured laminates. The impregnation quality was assessed by means of ultrasonic-C-scanning and microscopy. It turned out that the properties of the biobased composite panels made of biobased epoxy resin and a biobased UP-resin from the company Nuplex in New Zealand were onlay slightly inferior to those produced with a conventional epoxy resin. A biobased PU-resin from the company USSC in the USA developed voids during curing. A tannin-based resin containing of formaldehyde was not processable.
