Dry sliding wear behaviour of stir-cast aluminium matrix composites(AMCs)containing LM13 alloy as matrix and ceramic particles as reinforcement was investigated.Two different ceramic particle reinforcements were used ...Dry sliding wear behaviour of stir-cast aluminium matrix composites(AMCs)containing LM13 alloy as matrix and ceramic particles as reinforcement was investigated.Two different ceramic particle reinforcements were used separately:synthetic ceramic particles(B_(4)C),and natural ceramic particles(ilmenite).Optical micrographs showed uniform dispersion of reinforced particles in the matrix material.Reinforced particles refined the grain size of eutectic silicon and changed its morphology to globular type.B_(4)C reinforced composites(BRCs)showed maximum improvement in hardness of AMCs.Ilmenite reinforced composites(IRCs)showed maximum reduction in coefficient of friction values due to strong matrix−reinforcement interfacial bonding caused by the formation of interfacial compounds.Dry sliding wear behaviour of composites was significantly improved as compared to base alloy.The low density and high hardness of B_(4)C particles resulted in high dislocation density around filler particles in BRCs.On the other hand,the low thermal conductivity of ilmenite particles resulted in early oxidation and formation of a tribo-layer on surface of IRCs.So,both types of reinforcements led to the improvement in wear properties of AMCs,though the mechanisms involved were very different.Thus,the low-cost ilmenite particles can be used as alternative fillers to the high-cost B_(4)C particles for processing of wear resistant composites.展开更多
The alumina toughened zirconia(ATZ) ceramic particle reinforced gray iron matrix surface composite was successfully manufactured by pressureless infi ltration. The porous preform played a key role in the infi ltrating...The alumina toughened zirconia(ATZ) ceramic particle reinforced gray iron matrix surface composite was successfully manufactured by pressureless infi ltration. The porous preform played a key role in the infi ltrating progress. The microstructure was observed by scanning electron microscopy(SEM); the phase constitutions was analyzed by X-ray diffraction(XRD); and the hardness and wear resistance of selected specimens were tested by hardness testing machine and abrasion testing machine, respectively. The addition of high carbon ferrochromium powders leads to the formation of white iron during solidifi cation. The wear volume loss rates of ATZ ceramic particle reinforced gray iron matrix surface composite decreases fi rst, and then tends to be stable. The wear resistance of the composite is 2.7 times higher than that of gray iron matrix. The reason is a combination of the surface hardness increase of gray iron matrix and ATZ ceramic particles and alloy carbides protecting effect on gray iron matrix.展开更多
Middle reinforcement content SiCp/Al composites（Vp=30%, 35% and 40%） for precision optical systems applications were fabricated by powder metallurgy technology. The composites were free of porosity and SiC particles...Middle reinforcement content SiCp/Al composites（Vp=30%, 35% and 40%） for precision optical systems applications were fabricated by powder metallurgy technology. The composites were free of porosity and SiC particles distributed uniformly in the composites. The mean linear coefficients of thermal expansion（20-100 ℃） of SiCp/Al composites ranged from 11.6×10-6 to 13.3×10-6 K-1 and decreased with an increase in volume fraction of SiC content. The experimental coeffi cients of thermal expansion agreed well with predicted values based on Kerner＇s model. The Brinell hardness increased from 116 to 147, and the modulus increased from 99 to 112 GPa for the corresponding composites. The tensile strengths were higher than 320 MPa, but no signifi cant increasing trend between tensile strength and SiC content was observed.展开更多
SnCu solder is one of the most promising substitutes of SnPb solder, but its creep resistance is worse than that of the other lead-free solders. Particle-reinforcement is a way to improve the creep resistance of solde...SnCu solder is one of the most promising substitutes of SnPb solder, but its creep resistance is worse than that of the other lead-free solders. Particle-reinforcement is a way to improve the creep resistance of solder alloys and cause much more attention than before. A novel Ag particles reinforced SnCu based composite solder is formed and the influence of stress on creep behavior of the composite solder is investigated. Results indicate that the creep resistance of solder joints is superior to that of the SnCu solder joints. Creep rupture lifetime of solder joints decreases gradually with stress increasing. And the creep rupture lifetime of the composite solder joints falls down faster than that of the matrix solder joints.展开更多
The dry sliding wear behavior of AA6061 matrix composite reinforced with aluminium nitride particles（AlN） produced by stir casting process was investigated. A regression model was developed to predict the wear rate ...The dry sliding wear behavior of AA6061 matrix composite reinforced with aluminium nitride particles（AlN） produced by stir casting process was investigated. A regression model was developed to predict the wear rate of the prepared composite. A four-factor, five-level central composite rotatable design matrix was used to minimize the number of experimental runs. The factors considered in this study were sliding velocity, sliding distance, normal load and mass fraction of AlN reinforcement in the matrix. The developed regression model was validated by statistical software SYSTAT 12 and statistical tools such as analysis of variance（ANOVA） and student＇s t test. It was found that the developed regression model could be effectively used to predict the wear rate at 95% confidence level. The influence of these factors on wear rate of AA6061/AlNp composite was analyzed using the developed regression model and predicted trends were discussed with the aid of worn surface morphologies. The regression model indicated that the wear rate of cast AA6061/AlNp composite decreased with an increase in the mass fraction of AlN and increased with an increase of the sliding velocity, sliding distance and normal load acting on the composite specimen.展开更多
文摘Dry sliding wear behaviour of stir-cast aluminium matrix composites(AMCs)containing LM13 alloy as matrix and ceramic particles as reinforcement was investigated.Two different ceramic particle reinforcements were used separately:synthetic ceramic particles(B_(4)C),and natural ceramic particles(ilmenite).Optical micrographs showed uniform dispersion of reinforced particles in the matrix material.Reinforced particles refined the grain size of eutectic silicon and changed its morphology to globular type.B_(4)C reinforced composites(BRCs)showed maximum improvement in hardness of AMCs.Ilmenite reinforced composites(IRCs)showed maximum reduction in coefficient of friction values due to strong matrix−reinforcement interfacial bonding caused by the formation of interfacial compounds.Dry sliding wear behaviour of composites was significantly improved as compared to base alloy.The low density and high hardness of B_(4)C particles resulted in high dislocation density around filler particles in BRCs.On the other hand,the low thermal conductivity of ilmenite particles resulted in early oxidation and formation of a tribo-layer on surface of IRCs.So,both types of reinforcements led to the improvement in wear properties of AMCs,though the mechanisms involved were very different.Thus,the low-cost ilmenite particles can be used as alternative fillers to the high-cost B_(4)C particles for processing of wear resistant composites.
基金financially supported by the Scientific Research Fund of Si Chuan Provincial Education Department(No.17ZA0395)the Doctoral Program Foundation of Southwest University of Science and Technology(No.10zx7113)
文摘The alumina toughened zirconia(ATZ) ceramic particle reinforced gray iron matrix surface composite was successfully manufactured by pressureless infi ltration. The porous preform played a key role in the infi ltrating progress. The microstructure was observed by scanning electron microscopy(SEM); the phase constitutions was analyzed by X-ray diffraction(XRD); and the hardness and wear resistance of selected specimens were tested by hardness testing machine and abrasion testing machine, respectively. The addition of high carbon ferrochromium powders leads to the formation of white iron during solidifi cation. The wear volume loss rates of ATZ ceramic particle reinforced gray iron matrix surface composite decreases fi rst, and then tends to be stable. The wear resistance of the composite is 2.7 times higher than that of gray iron matrix. The reason is a combination of the surface hardness increase of gray iron matrix and ATZ ceramic particles and alloy carbides protecting effect on gray iron matrix.
基金Funded by the National Natural Science Foundation of China(51371077)
文摘Middle reinforcement content SiCp/Al composites（Vp=30%, 35% and 40%） for precision optical systems applications were fabricated by powder metallurgy technology. The composites were free of porosity and SiC particles distributed uniformly in the composites. The mean linear coefficients of thermal expansion（20-100 ℃） of SiCp/Al composites ranged from 11.6×10-6 to 13.3×10-6 K-1 and decreased with an increase in volume fraction of SiC content. The experimental coeffi cients of thermal expansion agreed well with predicted values based on Kerner＇s model. The Brinell hardness increased from 116 to 147, and the modulus increased from 99 to 112 GPa for the corresponding composites. The tensile strengths were higher than 320 MPa, but no signifi cant increasing trend between tensile strength and SiC content was observed.
基金Project(2004-294) supported by the Innovative Ability Foundation of Henan Province, China
文摘SnCu solder is one of the most promising substitutes of SnPb solder, but its creep resistance is worse than that of the other lead-free solders. Particle-reinforcement is a way to improve the creep resistance of solder alloys and cause much more attention than before. A novel Ag particles reinforced SnCu based composite solder is formed and the influence of stress on creep behavior of the composite solder is investigated. Results indicate that the creep resistance of solder joints is superior to that of the SnCu solder joints. Creep rupture lifetime of solder joints decreases gradually with stress increasing. And the creep rupture lifetime of the composite solder joints falls down faster than that of the matrix solder joints.
文摘The dry sliding wear behavior of AA6061 matrix composite reinforced with aluminium nitride particles（AlN） produced by stir casting process was investigated. A regression model was developed to predict the wear rate of the prepared composite. A four-factor, five-level central composite rotatable design matrix was used to minimize the number of experimental runs. The factors considered in this study were sliding velocity, sliding distance, normal load and mass fraction of AlN reinforcement in the matrix. The developed regression model was validated by statistical software SYSTAT 12 and statistical tools such as analysis of variance（ANOVA） and student＇s t test. It was found that the developed regression model could be effectively used to predict the wear rate at 95% confidence level. The influence of these factors on wear rate of AA6061/AlNp composite was analyzed using the developed regression model and predicted trends were discussed with the aid of worn surface morphologies. The regression model indicated that the wear rate of cast AA6061/AlNp composite decreased with an increase in the mass fraction of AlN and increased with an increase of the sliding velocity, sliding distance and normal load acting on the composite specimen.
