We studied the effect of loose tenon dimensions on stress and strain distributions in T-shaped mortise and loose tenon （M＆amp;LT） furni-ture joints under uniaxial bending loads, and determined the effects of loose ...We studied the effect of loose tenon dimensions on stress and strain distributions in T-shaped mortise and loose tenon （M＆amp;LT） furni-ture joints under uniaxial bending loads, and determined the effects of loose tenon length （30, 45, 60, and 90 mm） and loose tenon thickness （6 and 8 mm） on bending moment capacity of M＆amp;LT joints constructed with polyvinyl acetate （PVAc） adhesive. Stress and strain distributions in joint elements were then estimated for each joint using ANSYS finite element （FE） software. The bending moment capacity of joints increased significantly with thickness and length of the tenon. Based on the FE analysis results, under uniaxial bending, the highest shear stress values were obtained in the middle parts of the tenon, while the highest shear elastic strain values were estimated in glue lines between the tenon sur-faces and walls of the mortise. Shear stress and shear elastic strain values in joint elements generally increased with tenon dimensions and corre-sponding bending moment capacities. There was consistency between predicted maximum shear stress values and failure modes of the joints.展开更多
We determined the effects of adhesive type and loose tenon dimensions （length and thickness） on bending strength of T-shaped mor- tise and loose-tenon joints. Polyvinyl acetate （PVAc） and two-component polyuretha...We determined the effects of adhesive type and loose tenon dimensions （length and thickness） on bending strength of T-shaped mor- tise and loose-tenon joints. Polyvinyl acetate （PVAc） and two-component polyurethane （PU） adhesives were used to construct joint specimens. The bending moment capacity of joints increased significantly with increased length and thickness of the loose tenon. Bending moment capacity of joints constructed with PU adhesive was approximately 13% higher than for joints constructed with PVAc adhesive. We developed a predictive equation as a function of adhesive type and loose tenon dimensions to estimate the strength of the joints constructed of oriental beech （Fagus orientalis L.） under uniaxial bending load.展开更多
As the outfield load spectrum is so complicated that it cannot be used directly for test study in laboratory.This paper presents a method to determine load spectrum for high and low cycle combined fatigue of turbine m...As the outfield load spectrum is so complicated that it cannot be used directly for test study in laboratory.This paper presents a method to determine load spectrum for high and low cycle combined fatigue of turbine mortise at elevated temperature through experimental and numerical method.First of all,the low cycle load spectrum with duration time is determined through cumulative damage rule.The rain flow counting method is applied to obtain main cycles and sub cycles,and then the stress cycle is converted into pulsation cycle(stress ratio=0)based on the S-N curve and the Goodman curve;Secondly,three groups of different amplitudes tests are established to determine the high cycle amplitude.Finally,another three groups of the high-low combined cycle fatigue(HLCCF)tests for turbine mortise of a certain type engine are carried out.The results show that the macro and micro failure modes are identical with outfield's,which verifies the accuracy of the conversion method.展开更多
文摘We studied the effect of loose tenon dimensions on stress and strain distributions in T-shaped mortise and loose tenon （M＆amp;LT） furni-ture joints under uniaxial bending loads, and determined the effects of loose tenon length （30, 45, 60, and 90 mm） and loose tenon thickness （6 and 8 mm） on bending moment capacity of M＆amp;LT joints constructed with polyvinyl acetate （PVAc） adhesive. Stress and strain distributions in joint elements were then estimated for each joint using ANSYS finite element （FE） software. The bending moment capacity of joints increased significantly with thickness and length of the tenon. Based on the FE analysis results, under uniaxial bending, the highest shear stress values were obtained in the middle parts of the tenon, while the highest shear elastic strain values were estimated in glue lines between the tenon sur-faces and walls of the mortise. Shear stress and shear elastic strain values in joint elements generally increased with tenon dimensions and corre-sponding bending moment capacities. There was consistency between predicted maximum shear stress values and failure modes of the joints.
文摘We determined the effects of adhesive type and loose tenon dimensions （length and thickness） on bending strength of T-shaped mor- tise and loose-tenon joints. Polyvinyl acetate （PVAc） and two-component polyurethane （PU） adhesives were used to construct joint specimens. The bending moment capacity of joints increased significantly with increased length and thickness of the loose tenon. Bending moment capacity of joints constructed with PU adhesive was approximately 13% higher than for joints constructed with PVAc adhesive. We developed a predictive equation as a function of adhesive type and loose tenon dimensions to estimate the strength of the joints constructed of oriental beech （Fagus orientalis L.） under uniaxial bending load.
基金This work is supported by National Natural Science Foundation of China(51305012)Doctoral Fund of Ministry of Education of China(20111102120011)National Natural Science Foundation of China(51375031).The writers are grateful。
文摘As the outfield load spectrum is so complicated that it cannot be used directly for test study in laboratory.This paper presents a method to determine load spectrum for high and low cycle combined fatigue of turbine mortise at elevated temperature through experimental and numerical method.First of all,the low cycle load spectrum with duration time is determined through cumulative damage rule.The rain flow counting method is applied to obtain main cycles and sub cycles,and then the stress cycle is converted into pulsation cycle(stress ratio=0)based on the S-N curve and the Goodman curve;Secondly,three groups of different amplitudes tests are established to determine the high cycle amplitude.Finally,another three groups of the high-low combined cycle fatigue(HLCCF)tests for turbine mortise of a certain type engine are carried out.The results show that the macro and micro failure modes are identical with outfield's,which verifies the accuracy of the conversion method.
