根据光温对作物叶面积的影响,提出了辐热积(product of the rma leffectiveness and PAR,TEP)的概念。根据试验资料构建了利用辐热积模拟番茄(Lycopersicon esculentum Mill)叶面积动态的数学模型,并将其与已有的光合作用和干物质生产...根据光温对作物叶面积的影响,提出了辐热积(product of the rma leffectiveness and PAR,TEP)的概念。根据试验资料构建了利用辐热积模拟番茄(Lycopersicon esculentum Mill)叶面积动态的数学模型,并将其与已有的光合作用和干物质生产模拟模型相结合,构建了温室番茄干物质生产动态模型。利用不同品种、基质和地点的试验资料对模型进行了检验。结果表明,与传统的比叶面积法和有效积温法相比,辐热积法显著提高了温室番茄叶面积的预测精度,提高了光合作用和干物质生产的模拟精度。辐热积法对番茄叶面积的预测结果与1:1直线之间的决定系数R2和统计回归标准误差RMSE分别为0.9743和0.0515m2·株-1,对植株总干物质量的预测结果与1:1直线之间的R2和RMSE分别为0.9360和522.7104kg·ha-1;采用辐热积法对植株总干物质量的预测精度比有效积温法和比叶面积法分别提高56%和72%。展开更多
A hydroponic experiment was conducted to study the effect of partial replacement of NO-3-N by NH4+-N on the seedling growth and organic acid content of tomato (Lycopersicon esculentum Mill.). A completely randomized d...A hydroponic experiment was conducted to study the effect of partial replacement of NO-3-N by NH4+-N on the seedling growth and organic acid content of tomato (Lycopersicon esculentum Mill.). A completely randomized design was established with three replications and five treatments, i.e., NO-3-N/NH4+-N of 100/0, 75/25, 50/50, 25/75 and 0/100. Results showed that 25% replacement of NO3--N by NH4+-N significantly (P = 0.05) improved fresh and dry weight, revealing that a proper percentage of NH4+-N was important for tomato nitrogen nutrition. This could increase the plant growth even though tomato was a crop that preferred nitrate nutrition. Also an increase in the proportion of NH4+-N in the nutrient solution led to a significant decrease (P = 0.05) in malate, citrate and fumarate. However, the 25% NH4+-N plus 75% NO3--N treatment had no significant effect (P = 0.05) on the 2-ketoglutarate, succinate or oxalic acid content, showing that only some organic acids in tomato plants were affected. Only pyruvate increased significantly (P = 0.05), and it only increased for 25% and 50% replacement of NO3--N by NH4+-N. Metabolism of these organic acids, especially malate, citrate and fumarate, should be further studied at the molecular level in vegetables applied with different nitrogen forms.展开更多
The effects of heat treatment on the properties of multi element wear-resistant low-alloy steel （MLAWS） which is used to make the liner of rolling mill torus were researched. The results show that when quenching tem...The effects of heat treatment on the properties of multi element wear-resistant low-alloy steel （MLAWS） which is used to make the liner of rolling mill torus were researched. The results show that when quenching temperature is lower than 900℃, the hardness increases with the increase of temperature, and when quenching temperature is higher than 900℃, the hardness decreases with the increase of temperature. As quenching temperature is lower than 920℃, the effect of quenching temperature on the impact toughness is not obvious. When quenching temperature is higher than 920℃ , impact toughness decreases with the increase of temperature. When tempering temperature is higher than 450 ℃ , the hardness begins to decrease obviously. After tempering at 350℃, the best wear resistance was obtained. According to the service condition of rolling mill torus liner, the MLAWS is quenched from 900-920 ℃ and tempered at 350-370℃.展开更多
Steel strips are the main of steel products and flatness is an important quality indicator of steel strips. Flatness control is the key and highly difficult technique of strip mills. The bottle-neck restricting the im...Steel strips are the main of steel products and flatness is an important quality indicator of steel strips. Flatness control is the key and highly difficult technique of strip mills. The bottle-neck restricting the improvement of flatness control techniques is that the research on flatness theories and control mathematic models is not in accordance with the requirement of technique developments. To build a simple, rapid and accurate explicit formulation control model has become an urgent need for the development of flatness control technique. This paper puts forward the conception of dynamic effective matrix based on the effective matrix method for flatness control proposed by the authors under the consideration of the influence of the change of parameters in roiling processes on the effective matrix, and the concept is validated by industrial productions. Three methods of the effective matrix generation are induced： the calculation method based on the flatness prediction model; the calculation method based on the data excavation in rolling processes and the direct calculation method based on the network model. A fuzzy neural network effective matrix model is built based on the clusters, and then the network structure is optimized and the high-speed-calculation problem of the dynamic effective matrix is solved. The flatness control scheme for cold strip mills is proposed based on the dynamic effective matrix. On stand 5 of the 1 220 mm five-stand 4-high cold strip tandem mill, the industrial experiment with the control methods of tilting roll and bending roll is done by the control scheme of the static effective matrix and the dynamic effective matrix, respectively. The experiment result proves that the control effect of the dynamic effective matrix is much better than that of the static effective matrix. This paper proposes a new idea and method for the dynamic flatness control in the rolling processes of cold strip mills and develops the theory and model of the flatness control effective matrix method.展开更多
In this work, a scalable and cost-effective method including mechanical milling, centrifugation and spray drying was developed to fabricate Si nanoparticles.The synthesized Si nanoparticles show an average size of 62 ...In this work, a scalable and cost-effective method including mechanical milling, centrifugation and spray drying was developed to fabricate Si nanoparticles.The synthesized Si nanoparticles show an average size of 62 nm and exhibit a narrow particle size distribution. The influence of particle sizes on electrochemical performance of Si-based electrode was investigated, and it is found that as the particle size decreases in the studied range, the Si particles show a lower specific capacity and a higher irreversible capacity loss(ICL). Furthermore, an oxide layer with thickness of ～3 nm was detected on the surface of the as-received Si nanoparticles, and this layer can be effectively removed by hydrofluoric acid(HF) etching,resulting in much improved electrochemical performance over the as-received samples.展开更多
Four irrigation treatments were designed with 2,4,6 and 8 d intervals to irrigate, respectively. Watering was stopped when the reading of the moisture tension sensor reached zero. The results indicated that glucose an...Four irrigation treatments were designed with 2,4,6 and 8 d intervals to irrigate, respectively. Watering was stopped when the reading of the moisture tension sensor reached zero. The results indicated that glucose and fructose content of tomato's fruit were increased but sucrose content was decreased with fruit growth and development. In different stages, carbohydrate content of tomato fruit in the treatment 3 was the highest, in the treatment 2 was higher, and in the other treatments was the lowest. SS(sucrose synthase)activity was decreased but SPS(sucrose phosphate synthase)activity was increased with development of tomato. SS and SPS activity were increased but acid invertase and neutral invertase activity of ripe stage were decreased under deficit irrigation. Glucose and fructose content were increased in leaves of tomato under water deficit. Soluble sugars, organic acid and the ratio of sugar/acid in tomato fruits were increased and dry matter accumulation of plant was enhanced under water deficit. But the growth of fruits upside the plant and its dry matter accumulation were badly affected under water stress.展开更多
Underground mining always create voids.These voids can cause subsidence of surface.So it is always a demand to fill the void in such a manner that the effect of underground mining can be minimized.Void filling using m...Underground mining always create voids.These voids can cause subsidence of surface.So it is always a demand to fill the void in such a manner that the effect of underground mining can be minimized.Void filling using mill tailings especially in metal mining is one of the best techniques.The tailings produced in milling process have traditionally been disposed in tailing ponds creating a waste disposal and environmental problems in terms of land degradation,air and water pollution,etc.This disposal practice is more acute in the metal milling industry where the fine grinding,required for value liberation,results in the production of very fine tailings in large percentage.This paper includes discussions on the effectiveness of different paste mixes with varying cement contents in paste backfilling operations.The results revealed that material composition and use of super plasticizer strongly influenced the strength of cemented backfill.展开更多
文摘根据光温对作物叶面积的影响,提出了辐热积(product of the rma leffectiveness and PAR,TEP)的概念。根据试验资料构建了利用辐热积模拟番茄(Lycopersicon esculentum Mill)叶面积动态的数学模型,并将其与已有的光合作用和干物质生产模拟模型相结合,构建了温室番茄干物质生产动态模型。利用不同品种、基质和地点的试验资料对模型进行了检验。结果表明,与传统的比叶面积法和有效积温法相比,辐热积法显著提高了温室番茄叶面积的预测精度,提高了光合作用和干物质生产的模拟精度。辐热积法对番茄叶面积的预测结果与1:1直线之间的决定系数R2和统计回归标准误差RMSE分别为0.9743和0.0515m2·株-1,对植株总干物质量的预测结果与1:1直线之间的R2和RMSE分别为0.9360和522.7104kg·ha-1;采用辐热积法对植株总干物质量的预测精度比有效积温法和比叶面积法分别提高56%和72%。
基金Project supported by the National Natural Science Foundation of China (No. 30270790) and National Post-doctoral Foundation of China (No. 2003033494).
文摘A hydroponic experiment was conducted to study the effect of partial replacement of NO-3-N by NH4+-N on the seedling growth and organic acid content of tomato (Lycopersicon esculentum Mill.). A completely randomized design was established with three replications and five treatments, i.e., NO-3-N/NH4+-N of 100/0, 75/25, 50/50, 25/75 and 0/100. Results showed that 25% replacement of NO3--N by NH4+-N significantly (P = 0.05) improved fresh and dry weight, revealing that a proper percentage of NH4+-N was important for tomato nitrogen nutrition. This could increase the plant growth even though tomato was a crop that preferred nitrate nutrition. Also an increase in the proportion of NH4+-N in the nutrient solution led to a significant decrease (P = 0.05) in malate, citrate and fumarate. However, the 25% NH4+-N plus 75% NO3--N treatment had no significant effect (P = 0.05) on the 2-ketoglutarate, succinate or oxalic acid content, showing that only some organic acids in tomato plants were affected. Only pyruvate increased significantly (P = 0.05), and it only increased for 25% and 50% replacement of NO3--N by NH4+-N. Metabolism of these organic acids, especially malate, citrate and fumarate, should be further studied at the molecular level in vegetables applied with different nitrogen forms.
基金ItemSponsored by Tackle-Key-Programof Science and Technology Committee of Henan Province (042426002 ,0535010700)Henan Innovation Project for University Prominent Research Talents (2006KYCX022)
文摘The effects of heat treatment on the properties of multi element wear-resistant low-alloy steel （MLAWS） which is used to make the liner of rolling mill torus were researched. The results show that when quenching temperature is lower than 900℃, the hardness increases with the increase of temperature, and when quenching temperature is higher than 900℃, the hardness decreases with the increase of temperature. As quenching temperature is lower than 920℃, the effect of quenching temperature on the impact toughness is not obvious. When quenching temperature is higher than 920℃ , impact toughness decreases with the increase of temperature. When tempering temperature is higher than 450 ℃ , the hardness begins to decrease obviously. After tempering at 350℃, the best wear resistance was obtained. According to the service condition of rolling mill torus liner, the MLAWS is quenched from 900-920 ℃ and tempered at 350-370℃.
基金supported by National Natural Science Foundation of China(Grant No. 50675186)Hebei Provincial Major Natural Science Foundation of China (Grant No. E2006001038)
文摘Steel strips are the main of steel products and flatness is an important quality indicator of steel strips. Flatness control is the key and highly difficult technique of strip mills. The bottle-neck restricting the improvement of flatness control techniques is that the research on flatness theories and control mathematic models is not in accordance with the requirement of technique developments. To build a simple, rapid and accurate explicit formulation control model has become an urgent need for the development of flatness control technique. This paper puts forward the conception of dynamic effective matrix based on the effective matrix method for flatness control proposed by the authors under the consideration of the influence of the change of parameters in roiling processes on the effective matrix, and the concept is validated by industrial productions. Three methods of the effective matrix generation are induced： the calculation method based on the flatness prediction model; the calculation method based on the data excavation in rolling processes and the direct calculation method based on the network model. A fuzzy neural network effective matrix model is built based on the clusters, and then the network structure is optimized and the high-speed-calculation problem of the dynamic effective matrix is solved. The flatness control scheme for cold strip mills is proposed based on the dynamic effective matrix. On stand 5 of the 1 220 mm five-stand 4-high cold strip tandem mill, the industrial experiment with the control methods of tilting roll and bending roll is done by the control scheme of the static effective matrix and the dynamic effective matrix, respectively. The experiment result proves that the control effect of the dynamic effective matrix is much better than that of the static effective matrix. This paper proposes a new idea and method for the dynamic flatness control in the rolling processes of cold strip mills and develops the theory and model of the flatness control effective matrix method.
基金financially supported by the National Natural Science Foundation of China (No. 51404030)the National Key Technologies Research and Development Program (No. 2016YFB0100400)+2 种基金the Natural Science Foundation of Beijing Municipality (No. 3154043)the Beijing Science and Technology Plan (No. Z151100000115015)the Beijing Nova Program (No. Z161100004916096)
文摘In this work, a scalable and cost-effective method including mechanical milling, centrifugation and spray drying was developed to fabricate Si nanoparticles.The synthesized Si nanoparticles show an average size of 62 nm and exhibit a narrow particle size distribution. The influence of particle sizes on electrochemical performance of Si-based electrode was investigated, and it is found that as the particle size decreases in the studied range, the Si particles show a lower specific capacity and a higher irreversible capacity loss(ICL). Furthermore, an oxide layer with thickness of ～3 nm was detected on the surface of the as-received Si nanoparticles, and this layer can be effectively removed by hydrofluoric acid(HF) etching,resulting in much improved electrochemical performance over the as-received samples.
基金supported by the National Natural Science Fundation of China(30170640)Natural Science Fund of Liaoning Provice,China(20022080).
文摘Four irrigation treatments were designed with 2,4,6 and 8 d intervals to irrigate, respectively. Watering was stopped when the reading of the moisture tension sensor reached zero. The results indicated that glucose and fructose content of tomato's fruit were increased but sucrose content was decreased with fruit growth and development. In different stages, carbohydrate content of tomato fruit in the treatment 3 was the highest, in the treatment 2 was higher, and in the other treatments was the lowest. SS(sucrose synthase)activity was decreased but SPS(sucrose phosphate synthase)activity was increased with development of tomato. SS and SPS activity were increased but acid invertase and neutral invertase activity of ripe stage were decreased under deficit irrigation. Glucose and fructose content were increased in leaves of tomato under water deficit. Soluble sugars, organic acid and the ratio of sugar/acid in tomato fruits were increased and dry matter accumulation of plant was enhanced under water deficit. But the growth of fruits upside the plant and its dry matter accumulation were badly affected under water stress.
文摘Underground mining always create voids.These voids can cause subsidence of surface.So it is always a demand to fill the void in such a manner that the effect of underground mining can be minimized.Void filling using mill tailings especially in metal mining is one of the best techniques.The tailings produced in milling process have traditionally been disposed in tailing ponds creating a waste disposal and environmental problems in terms of land degradation,air and water pollution,etc.This disposal practice is more acute in the metal milling industry where the fine grinding,required for value liberation,results in the production of very fine tailings in large percentage.This paper includes discussions on the effectiveness of different paste mixes with varying cement contents in paste backfilling operations.The results revealed that material composition and use of super plasticizer strongly influenced the strength of cemented backfill.
