Vacuum die casting can reduce the'air entrapment'phenomenon during casting process.Based on the temperature measurements at metal-die interface with different processing parameters,such as slow shot speed(VL),...Vacuum die casting can reduce the'air entrapment'phenomenon during casting process.Based on the temperature measurements at metal-die interface with different processing parameters,such as slow shot speed(VL),high shot speed(VH),pouring temperature(Tp)and initial die temperature(Tm),inverse method was developed to determine the interfacial heat transfer coefficient(IHTC).The results indicate that a closer contact between the casting and die could be achieved when the vacuum system is used.It is found that the vacuum could strongly increase the values of IHTC and decrease the grain size in castings.The IHTC could have a higher peak value with increasing the Tp from680to720℃or the VL from0.1to0.4m/s.In addition,the influence of the VH and Tm on IHTC could be negligible.展开更多
Heat transfer at the metal-die interface has a great influence on the solidification process and casting structure. As thin-wall components are extensively produced by high pressure die casting process(HPDC), the B390...Heat transfer at the metal-die interface has a great influence on the solidification process and casting structure. As thin-wall components are extensively produced by high pressure die casting process(HPDC), the B390 alloy finger-plate casting was cast against an H13 steel die on a cold-chamber HPDC machine. The interfacial heat transfer behavior at different positions of the die was carefully studied using an inverse approach based on the temperature measurements inside the die. Furthermore, the filling process and the solidification rate in different finger-plates were also given to explain the distribution of interfacial heat flux(q) and interfacial heat transfer coefficient(h). Measurement results at the side of sprue indicates that qmax and hmax could reach 9.2 MW·m^(-2) and 64.3 kW ·m^(-2)·K^(-1), respectively. The simulation of melt flow in the die reveals that the thinnest(T_1) finger plate could accelerate the melt flow from 50 m·s^(-1) to 110 m·s^(-1). Due to this high velocity, the interfacial heat flux at the end of T_1 could firstly reach a highest value 7.92 MW·m^(-2) among the ends of T_n(n=2,3,4,5). In addition, the q_(max) and h_(max) values of T_2, T_4 and T_5 finger-plates increase with the increasing thickness of the finger plate. Finally, at the rapid decreasing stage of interfacial heat transfer coefficient(h), the decreasing rate of h has an exponential relationship with the increasing rate of solid fraction(f).展开更多
High pressure die casting copper is used to produce rotors for induction motors to improve efficiency.Experiments were carried out for a special"step-shape"casting with different step thicknesses.Based on th...High pressure die casting copper is used to produce rotors for induction motors to improve efficiency.Experiments were carried out for a special"step-shape"casting with different step thicknesses.Based on the measured temperature inside the die,the interfacial heat transfer coefficient(IHTC)at the metal/die interface during vacuum die casting was evaluated by solving the inverse problem.The IHTC peak value was 4.5×10^3-11×10^3 W·m^-2·K^-1 under the basic operation condition.The influences of casting pressure,fast shot speed,pouring temperature and initial die surface temperature on the IHTC peak values were investigated.Results show that a greater casting pressure and faster shot speed could only increase the IHTC peak values at the location close to the ingate.An increase of pouring temperature and/or initial die surface temperature significantly increases the IHTC peak values.展开更多
基金Project (2016YFB0301001) supported by the National Key Research and Development Program of ChinaProject (2015M580093) supported by the General Financial Grant from the China Postdoctoral Science Foundation of China
文摘Vacuum die casting can reduce the'air entrapment'phenomenon during casting process.Based on the temperature measurements at metal-die interface with different processing parameters,such as slow shot speed(VL),high shot speed(VH),pouring temperature(Tp)and initial die temperature(Tm),inverse method was developed to determine the interfacial heat transfer coefficient(IHTC).The results indicate that a closer contact between the casting and die could be achieved when the vacuum system is used.It is found that the vacuum could strongly increase the values of IHTC and decrease the grain size in castings.The IHTC could have a higher peak value with increasing the Tp from680to720℃or the VL from0.1to0.4m/s.In addition,the influence of the VH and Tm on IHTC could be negligible.
基金financially supported by the class General Financial Grant from the China Postdoctoral Science Foundation(No.2015M580093)the National Nature Science Foundation of China(No.20151301587)the National Major Science and Technology Program of China(No.2012ZX04012011)
文摘Heat transfer at the metal-die interface has a great influence on the solidification process and casting structure. As thin-wall components are extensively produced by high pressure die casting process(HPDC), the B390 alloy finger-plate casting was cast against an H13 steel die on a cold-chamber HPDC machine. The interfacial heat transfer behavior at different positions of the die was carefully studied using an inverse approach based on the temperature measurements inside the die. Furthermore, the filling process and the solidification rate in different finger-plates were also given to explain the distribution of interfacial heat flux(q) and interfacial heat transfer coefficient(h). Measurement results at the side of sprue indicates that qmax and hmax could reach 9.2 MW·m^(-2) and 64.3 kW ·m^(-2)·K^(-1), respectively. The simulation of melt flow in the die reveals that the thinnest(T_1) finger plate could accelerate the melt flow from 50 m·s^(-1) to 110 m·s^(-1). Due to this high velocity, the interfacial heat flux at the end of T_1 could firstly reach a highest value 7.92 MW·m^(-2) among the ends of T_n(n=2,3,4,5). In addition, the q_(max) and h_(max) values of T_2, T_4 and T_5 finger-plates increase with the increasing thickness of the finger plate. Finally, at the rapid decreasing stage of interfacial heat transfer coefficient(h), the decreasing rate of h has an exponential relationship with the increasing rate of solid fraction(f).
文摘High pressure die casting copper is used to produce rotors for induction motors to improve efficiency.Experiments were carried out for a special"step-shape"casting with different step thicknesses.Based on the measured temperature inside the die,the interfacial heat transfer coefficient(IHTC)at the metal/die interface during vacuum die casting was evaluated by solving the inverse problem.The IHTC peak value was 4.5×10^3-11×10^3 W·m^-2·K^-1 under the basic operation condition.The influences of casting pressure,fast shot speed,pouring temperature and initial die surface temperature on the IHTC peak values were investigated.Results show that a greater casting pressure and faster shot speed could only increase the IHTC peak values at the location close to the ingate.An increase of pouring temperature and/or initial die surface temperature significantly increases the IHTC peak values.
