The high-energy photon source(HEPS)is the first fourth-generation synchrotron light source facility in China.The HEPS injector consists of a linear accelerator(Linac)and a full energy booster.The booster captures the ...The high-energy photon source(HEPS)is the first fourth-generation synchrotron light source facility in China.The HEPS injector consists of a linear accelerator(Linac)and a full energy booster.The booster captures the electron beam from the Linac and increases its energy to the value required for the storage ring.The full-energy beam could be injected to the storage ring directly or after“high-energy accumulation.”On November 17,2023,the key booster parameters successfully reached their corresponding target values.These milestone results were achieved based on numerous contributions,including nearly a decade of physical design,years of equipment development and installation,and months of beam commissioning.As measured at the extraction energy of 6 GeV,the averaged beam current and emittance reached 8.57 mA with 5 bunches and 30.37 nm rad with a single-bunch charge of 5.58 nC,compared with the corresponding target values of 6.6 mA and 35 nm rad,respectively.This paper presents the physical design,equipment development,installation,and commissioning process of the HEPS booster.展开更多
A novel small-molecule(SM) acceptor DTF-IC is designed and synthesized in this work. The power conversion efficiency(PCE) of ternary OSCs increased up to 12.14% from 10.90% by incorporating 10 wt% of DTF-IC as second ...A novel small-molecule(SM) acceptor DTF-IC is designed and synthesized in this work. The power conversion efficiency(PCE) of ternary OSCs increased up to 12.14% from 10.90% by incorporating 10 wt% of DTF-IC as second acceptors into the binary OSCs consisting of PBDB-T as donor and IT-M as acceptor. This was mainly due to the large increase in short-circuit current(Jsc) from 16.18 to 17.95 mA/cm^2, without any drop in the open-circuit voltage(Voc) and fill factor(FF). The addition of DTF-IC enabled the donor and acceptor to form a distinct complementary absorption profile in the visible-light region, which boosted the photon harvesting in the range of 730–800 nm and consequently increased the Jscof the ternary system by 11%. Moreover, there was an energy transfer between the two SM acceptors, favorable for enhancing charge separation and transfer as well as reducing charge recombination at PBDB-T:IT-M and PBDB-T:DTF-IC interface. Simultaneously, HOMO and LUMO energy levels of DTF-IC were lower than those of PBDB-T, but still higher than those of IT-M. Thus, DTF-IC is able to provide a cascading energy level with the host donor and acceptor which are beneficial for efficient charge transfer between the acceptors and facilitating exciton dissociation and carrier transport. Meanwhile, the highly crystalline DTF-IC as a third component can improve the crystallization process of the active layer while maintaining proper phase separation. This work proposes a novel idea for non-fullerene acceptors achieved via twin spiro-type structure modifying by indanone and provides a new direction for the selection of ternary solar cell materials.展开更多
Purpose Superconducting 166.6-MHz cavities will be used to accelerate electron beams in high-energy photon source(HEPS).The radio-frequency(RF)fields inside these cavities have to be controlled better than 0.03%(rms e...Purpose Superconducting 166.6-MHz cavities will be used to accelerate electron beams in high-energy photon source(HEPS).The radio-frequency(RF)fields inside these cavities have to be controlled better than 0.03%(rms error)for the amplitude and 0.03◦(rms error)for the phase.Adopting a quarter-wave geometry withβ=1,the 166.6-MHz cavity has two intrinsic mechanical modes at∼100Hz observed in both simulations and cryogenic tests.If coupled to external vibrations,these microphonics modes shall stress the existing proportional–integral(PI)feedback controller and inevitably deteriorate the field stabilities.Therefore,additional noise suppression may be required.Methods Adigital low-level RF system previously in-house developedwas connected to a 166.6-MHz dressed cavity at room temperature in the laboratory.Piezo-tunerswere used to“knock”on the cavity at various frequencies to excite cavity vibrations,and microphonics spectrum was subsequently measured.A disturbance observer(DOB)-based algorithm was adopted and integrated into the existing feedback controller.The performance of PI controller,DOB controller and a combination of PI and DOB controller was compared.The limitation of the DOB controller was also examined.Results and conclusions The PI controller was proved to be insufficient in suppressing large cavity microphonics during the tests.By adding the DOB controller,the excellent field stabilities can be restored.Optimized loop parameters were obtained.The simple first-order filter was adequate thanks to the robustness of the DOB controller.This constitutes a first laboratory demonstration of the active microphonics noise suppression in the 166.6-MHz RF cavity for HEPS.展开更多
Objective:The study aimed to explore the characteristic of dose equivalent rates(DERs)of photon and neutron outside the treatment room under high-energy electron mode(dose rate 1000 MU/min)of linac and to evaluate the...Objective:The study aimed to explore the characteristic of dose equivalent rates(DERs)of photon and neutron outside the treatment room under high-energy electron mode(dose rate 1000 MU/min)of linac and to evaluate the effectiveness of treatment room protection.Methods:A 451 P pressurized ion chamber and a thermo neutron detector were used to measure the DERs of the photon and neutron at selected points.The effects of field size,applicator size,applicator,anthropomorphic phantom(CDP)and lead block on DER were investigated respectively.Results:The DERs of a photon at the center of shielding door(point A),control console(point B),primary shielding walls(point C,D)and roof of treatment room(point E)increased with increasing electron energy,but decreased with the increasing field size.The DERs of a photons at points A and B are smaller than 2.5μSv/h for all scenarios,while those at point D greater than 2.5μSv/h when irradiated by 18-22 Me V electron.In addition,CDP may change the DERs of a photon at points C and D about 5% to 30%.On the other hand,the DERs of neutron increase with increasing electron energy but decrease with the increase of field size and applicator size,however,the lead block and the applicator itself will change the DERs of leak neutron at point A,but its amplitude is less than 0.5μSv/h.The maximum DER of neutron at point A is 6.18μSv/h irradiated by 22 Me V electron.For other scenarios,they are all in the range of national standards limits.Conclusion:The DERs of a photon and neutron outside the treatment room mainly depend on the energy,field size and irradiation direction of the electron beam.If high-energy 18 Me V and 22 Me V electron beams will be used,the primary shielding walls and shielding doors need reconstructing or increasing thickness.展开更多
【目的】高能同步辐射光源HEPS(High Energy Photon Source)是我国第一台高能量同步辐射光源,预计2025年建成。HEPS建成后,首批投入使用的15条光束线站预计每天会产生200TB实验数据。为满足不同阶段对实验数据的读写需求,会对海量实验...【目的】高能同步辐射光源HEPS(High Energy Photon Source)是我国第一台高能量同步辐射光源,预计2025年建成。HEPS建成后,首批投入使用的15条光束线站预计每天会产生200TB实验数据。为满足不同阶段对实验数据的读写需求,会对海量实验数据进行分级存储和长期备份。如何将这些数据在不同存储介质之间稳定和高效地传输是HEPS实验中需要解决的重要问题。【方法】HEPS科学数据传输系统设计了多源DAQ接口、任务调度、消息队列、集群传输、日志监控、配置管理和消息通知等功能模块。【结论】系统实现了海量数据在不同存储介质间的高效、可靠传输。【结果】系统现部署在北京同步辐射多个线站,用作HEPS数据传输的前期验证,运行稳定、效果良好,为科研人员和用户提供了良好的数据传输服务。展开更多
In the lattice design of a diffraction-limited storage ring（DLSR） consisting of compact multi-bend achromats（MBAs）, it is challenging to simultaneously achieve an ultralow emittance and a satisfactory nonlinear pe...In the lattice design of a diffraction-limited storage ring（DLSR） consisting of compact multi-bend achromats（MBAs）, it is challenging to simultaneously achieve an ultralow emittance and a satisfactory nonlinear performance, due to extremely large nonlinearities and limited tuning ranges of the element parameters. Nevertheless, in this paper we show that the potential of a DLSR design can be explored with a successive and iterative implementation of the multi-objective particle swarm optimization（MOPSO） and multi-objective genetic algorithm（MOGA）. For the High Energy Photon Source, a planned kilometer-scale DLSR, optimizations indicate that it is feasible to attain a natural emittance of about 50 pm·rad, and simultaneously realize a sufficient ring acceptance for on-axis longitudinal injection, by using a hybrid MBA lattice. In particular, this study demonstrates that a rational combination of the MOPSO and MOGA is more effective than either of them alone, in approaching the true global optima of an explorative multi-objective problem with many optimizing variables and local optima.展开更多
基金This work was supported by the National Natural Science Foundation of China(No.12005239).
文摘The high-energy photon source(HEPS)is the first fourth-generation synchrotron light source facility in China.The HEPS injector consists of a linear accelerator(Linac)and a full energy booster.The booster captures the electron beam from the Linac and increases its energy to the value required for the storage ring.The full-energy beam could be injected to the storage ring directly or after“high-energy accumulation.”On November 17,2023,the key booster parameters successfully reached their corresponding target values.These milestone results were achieved based on numerous contributions,including nearly a decade of physical design,years of equipment development and installation,and months of beam commissioning.As measured at the extraction energy of 6 GeV,the averaged beam current and emittance reached 8.57 mA with 5 bunches and 30.37 nm rad with a single-bunch charge of 5.58 nC,compared with the corresponding target values of 6.6 mA and 35 nm rad,respectively.This paper presents the physical design,equipment development,installation,and commissioning process of the HEPS booster.
基金supported by the Startup Funding of Hebei University of Technology(208011)the National Key R&D Program of China(2017YFE0106000)+3 种基金the National Natural Science Foundation of China(51773212,21574144,and 61705240)Zhejiang Provincial Natural Science Foundation(LR16B040002)Ningbo Municipal Science and Technology Innovative Research Team(2015B11002 and 2016B10005)CAS Interdisciplinary Innovation Team,CAS Key Project of Frontier Science Research(QYZDB-SSW-SYS030),CAS Key Project of International Cooperation(174433KYSB20160065)
文摘A novel small-molecule(SM) acceptor DTF-IC is designed and synthesized in this work. The power conversion efficiency(PCE) of ternary OSCs increased up to 12.14% from 10.90% by incorporating 10 wt% of DTF-IC as second acceptors into the binary OSCs consisting of PBDB-T as donor and IT-M as acceptor. This was mainly due to the large increase in short-circuit current(Jsc) from 16.18 to 17.95 mA/cm^2, without any drop in the open-circuit voltage(Voc) and fill factor(FF). The addition of DTF-IC enabled the donor and acceptor to form a distinct complementary absorption profile in the visible-light region, which boosted the photon harvesting in the range of 730–800 nm and consequently increased the Jscof the ternary system by 11%. Moreover, there was an energy transfer between the two SM acceptors, favorable for enhancing charge separation and transfer as well as reducing charge recombination at PBDB-T:IT-M and PBDB-T:DTF-IC interface. Simultaneously, HOMO and LUMO energy levels of DTF-IC were lower than those of PBDB-T, but still higher than those of IT-M. Thus, DTF-IC is able to provide a cascading energy level with the host donor and acceptor which are beneficial for efficient charge transfer between the acceptors and facilitating exciton dissociation and carrier transport. Meanwhile, the highly crystalline DTF-IC as a third component can improve the crystallization process of the active layer while maintaining proper phase separation. This work proposes a novel idea for non-fullerene acceptors achieved via twin spiro-type structure modifying by indanone and provides a new direction for the selection of ternary solar cell materials.
文摘Purpose Superconducting 166.6-MHz cavities will be used to accelerate electron beams in high-energy photon source(HEPS).The radio-frequency(RF)fields inside these cavities have to be controlled better than 0.03%(rms error)for the amplitude and 0.03◦(rms error)for the phase.Adopting a quarter-wave geometry withβ=1,the 166.6-MHz cavity has two intrinsic mechanical modes at∼100Hz observed in both simulations and cryogenic tests.If coupled to external vibrations,these microphonics modes shall stress the existing proportional–integral(PI)feedback controller and inevitably deteriorate the field stabilities.Therefore,additional noise suppression may be required.Methods Adigital low-level RF system previously in-house developedwas connected to a 166.6-MHz dressed cavity at room temperature in the laboratory.Piezo-tunerswere used to“knock”on the cavity at various frequencies to excite cavity vibrations,and microphonics spectrum was subsequently measured.A disturbance observer(DOB)-based algorithm was adopted and integrated into the existing feedback controller.The performance of PI controller,DOB controller and a combination of PI and DOB controller was compared.The limitation of the DOB controller was also examined.Results and conclusions The PI controller was proved to be insufficient in suppressing large cavity microphonics during the tests.By adding the DOB controller,the excellent field stabilities can be restored.Optimized loop parameters were obtained.The simple first-order filter was adequate thanks to the robustness of the DOB controller.This constitutes a first laboratory demonstration of the active microphonics noise suppression in the 166.6-MHz RF cavity for HEPS.
基金Guangzhou Medical Key Discipline Construction Project(2017-2019):Cancer Therapeutics and Experimental Oncology Project,the Science and Technology Project of Guangzhou,grant number:201804010297。
文摘Objective:The study aimed to explore the characteristic of dose equivalent rates(DERs)of photon and neutron outside the treatment room under high-energy electron mode(dose rate 1000 MU/min)of linac and to evaluate the effectiveness of treatment room protection.Methods:A 451 P pressurized ion chamber and a thermo neutron detector were used to measure the DERs of the photon and neutron at selected points.The effects of field size,applicator size,applicator,anthropomorphic phantom(CDP)and lead block on DER were investigated respectively.Results:The DERs of a photon at the center of shielding door(point A),control console(point B),primary shielding walls(point C,D)and roof of treatment room(point E)increased with increasing electron energy,but decreased with the increasing field size.The DERs of a photons at points A and B are smaller than 2.5μSv/h for all scenarios,while those at point D greater than 2.5μSv/h when irradiated by 18-22 Me V electron.In addition,CDP may change the DERs of a photon at points C and D about 5% to 30%.On the other hand,the DERs of neutron increase with increasing electron energy but decrease with the increase of field size and applicator size,however,the lead block and the applicator itself will change the DERs of leak neutron at point A,but its amplitude is less than 0.5μSv/h.The maximum DER of neutron at point A is 6.18μSv/h irradiated by 22 Me V electron.For other scenarios,they are all in the range of national standards limits.Conclusion:The DERs of a photon and neutron outside the treatment room mainly depend on the energy,field size and irradiation direction of the electron beam.If high-energy 18 Me V and 22 Me V electron beams will be used,the primary shielding walls and shielding doors need reconstructing or increasing thickness.
文摘【目的】高能同步辐射光源HEPS(High Energy Photon Source)是我国第一台高能量同步辐射光源,预计2025年建成。HEPS建成后,首批投入使用的15条光束线站预计每天会产生200TB实验数据。为满足不同阶段对实验数据的读写需求,会对海量实验数据进行分级存储和长期备份。如何将这些数据在不同存储介质之间稳定和高效地传输是HEPS实验中需要解决的重要问题。【方法】HEPS科学数据传输系统设计了多源DAQ接口、任务调度、消息队列、集群传输、日志监控、配置管理和消息通知等功能模块。【结论】系统实现了海量数据在不同存储介质间的高效、可靠传输。【结果】系统现部署在北京同步辐射多个线站,用作HEPS数据传输的前期验证,运行稳定、效果良好,为科研人员和用户提供了良好的数据传输服务。
基金Supported by NSFC(11475202,11405187)Youth Innovation Promotion Association CAS(2015009)
文摘In the lattice design of a diffraction-limited storage ring（DLSR） consisting of compact multi-bend achromats（MBAs）, it is challenging to simultaneously achieve an ultralow emittance and a satisfactory nonlinear performance, due to extremely large nonlinearities and limited tuning ranges of the element parameters. Nevertheless, in this paper we show that the potential of a DLSR design can be explored with a successive and iterative implementation of the multi-objective particle swarm optimization（MOPSO） and multi-objective genetic algorithm（MOGA）. For the High Energy Photon Source, a planned kilometer-scale DLSR, optimizations indicate that it is feasible to attain a natural emittance of about 50 pm·rad, and simultaneously realize a sufficient ring acceptance for on-axis longitudinal injection, by using a hybrid MBA lattice. In particular, this study demonstrates that a rational combination of the MOPSO and MOGA is more effective than either of them alone, in approaching the true global optima of an explorative multi-objective problem with many optimizing variables and local optima.
