This paper discusses experimental results of turnin g experiments on GCr15 bearing steel hardened to 60～64 HRC. The objective was to d etermine the effect of the cutting parameters on cutting force, chip morphology a...This paper discusses experimental results of turnin g experiments on GCr15 bearing steel hardened to 60～64 HRC. The objective was to d etermine the effect of the cutting parameters on cutting force, chip morphology and resultant workpiece surface quality, more specifically surface texture, micr ostructure alterations, changes in microhardness and residual stresses distribut ion. The changing rules of the main cutting force was shown in this paper which feature a increasing tendency with the improvement of the workpiece hardness wit hin the cutting parameter scope. The rule of cutting force changing with the wor kpiece hardness is accord to the traditional metal cutting theory. Stress value decrease with increasing cutting speed and workpiece hardness. The comparison of the machined surface roughness and harden layer depth of machined surface for d ifferent hardness is shown in Fig.1. The machined surface roughness is the worst when the workpiece hardness is around 50HRC. When the workpiece hardness is ove r 50HRC, the surface roughness value shows a descending tendency with the additi on hardness. The machined superficial harden layer depth shows an increasing ten dency with the improvement of the workpiece hardness. When the workpiece hardnes s is 50HRC the machined superficial harden layer depth is tiptop. When the workp iece hardness is over 50HRC the depth changes little with the addition of workpi ece hardness. The remnant stress status of the machined surface is shown in Fig. 2, which is press stress status both in surface and in base for less cutting par ameters under two kinds of cutting condition. But experiment results show that t ensile stress can be produced under uncomfortable cutting conditions. The deform ation created by the chip formation is reduced whereduce with [TPP126A,+35mm77mm,Z,PY#]Depth from surface (μm) ■ v=200m/min,f=0.24mm/r,ap=0.8mm,60HRC ● v=200m/min,f=0.15mm/r,ap=0.5mm,60HRC Fig.1 The subsurface residual stress between the two experimentsHardness (HRC) Fig.2 The surface finis展开更多
A study was undertaken to investigate the performan ce of PCBN tool in the finish turning GCr15 bearing steel with different hardness between 30～64 HRC. The natural thermocouple was used to measure the cutting tem p ...A study was undertaken to investigate the performan ce of PCBN tool in the finish turning GCr15 bearing steel with different hardness between 30～64 HRC. The natural thermocouple was used to measure the cutting tem p erature, tool life and cutting temperature were investigated and compared. The m aterial can be heated by this instrument which using low voltage and high elec trical current, while PCBN can’t be heated by electrifying directly, so the ke ntanium layer coating over the PCBN is heated, so the PCBN is heated and its th ermoelectric property is got by this method. [TPP129,+60mm88mm,Y,PZ#] Fig.1 Effect of cutting depth and workpiec hardness on. the cutting temperatureThe objective was to determine the influence of the workpiece hardness on change s in cutting temperature and tool wear characterize. It can be found from Fig.1 that the cutting temperature show an increasing tendency with the improvement of workpiece hardness within the cutting speed scope when the workpiece hardness i s under HRC50. And on the other hand, it is found that the cutting temperature s how the downtrend with the improvement of workpiece hardness when the workpiece hardness is over HRC50. According to experimental results, the critical hard ness when turning hardened GCr15 bearing steel with PCBN tool is about HRC50. Th e wear causes of PCBN tool have been found out through taking photos on the micr o-shape of PCBN poly-laminate initial surface as well as face and flank of wea r tool and analysis on chemical elements. It is discovered that the PCBN tools a re not suitable for cutting the workpiece at nearly critical hardness, because n ear the critical hardness, PCBN wear at the highest speed. For researching the w ear rule of PCBN tool, the tool wear experiments have been carried on by using b earing steel GCr15 at hardness HRC40 and HRC60 with changing cutting speed. The indexes of tool life equations is gained under two kinds of conditions w hich are bigger than 0.6, so the effects of cutting speed on the PCBN tool are m u展开更多
文摘This paper discusses experimental results of turnin g experiments on GCr15 bearing steel hardened to 60～64 HRC. The objective was to d etermine the effect of the cutting parameters on cutting force, chip morphology and resultant workpiece surface quality, more specifically surface texture, micr ostructure alterations, changes in microhardness and residual stresses distribut ion. The changing rules of the main cutting force was shown in this paper which feature a increasing tendency with the improvement of the workpiece hardness wit hin the cutting parameter scope. The rule of cutting force changing with the wor kpiece hardness is accord to the traditional metal cutting theory. Stress value decrease with increasing cutting speed and workpiece hardness. The comparison of the machined surface roughness and harden layer depth of machined surface for d ifferent hardness is shown in Fig.1. The machined surface roughness is the worst when the workpiece hardness is around 50HRC. When the workpiece hardness is ove r 50HRC, the surface roughness value shows a descending tendency with the additi on hardness. The machined superficial harden layer depth shows an increasing ten dency with the improvement of the workpiece hardness. When the workpiece hardnes s is 50HRC the machined superficial harden layer depth is tiptop. When the workp iece hardness is over 50HRC the depth changes little with the addition of workpi ece hardness. The remnant stress status of the machined surface is shown in Fig. 2, which is press stress status both in surface and in base for less cutting par ameters under two kinds of cutting condition. But experiment results show that t ensile stress can be produced under uncomfortable cutting conditions. The deform ation created by the chip formation is reduced whereduce with [TPP126A,+35mm77mm,Z,PY#]Depth from surface (μm) ■ v=200m/min,f=0.24mm/r,ap=0.8mm,60HRC ● v=200m/min,f=0.15mm/r,ap=0.5mm,60HRC Fig.1 The subsurface residual stress between the two experimentsHardness (HRC) Fig.2 The surface finis
文摘A study was undertaken to investigate the performan ce of PCBN tool in the finish turning GCr15 bearing steel with different hardness between 30～64 HRC. The natural thermocouple was used to measure the cutting tem p erature, tool life and cutting temperature were investigated and compared. The m aterial can be heated by this instrument which using low voltage and high elec trical current, while PCBN can’t be heated by electrifying directly, so the ke ntanium layer coating over the PCBN is heated, so the PCBN is heated and its th ermoelectric property is got by this method. [TPP129,+60mm88mm,Y,PZ#] Fig.1 Effect of cutting depth and workpiec hardness on. the cutting temperatureThe objective was to determine the influence of the workpiece hardness on change s in cutting temperature and tool wear characterize. It can be found from Fig.1 that the cutting temperature show an increasing tendency with the improvement of workpiece hardness within the cutting speed scope when the workpiece hardness i s under HRC50. And on the other hand, it is found that the cutting temperature s how the downtrend with the improvement of workpiece hardness when the workpiece hardness is over HRC50. According to experimental results, the critical hard ness when turning hardened GCr15 bearing steel with PCBN tool is about HRC50. Th e wear causes of PCBN tool have been found out through taking photos on the micr o-shape of PCBN poly-laminate initial surface as well as face and flank of wea r tool and analysis on chemical elements. It is discovered that the PCBN tools a re not suitable for cutting the workpiece at nearly critical hardness, because n ear the critical hardness, PCBN wear at the highest speed. For researching the w ear rule of PCBN tool, the tool wear experiments have been carried on by using b earing steel GCr15 at hardness HRC40 and HRC60 with changing cutting speed. The indexes of tool life equations is gained under two kinds of conditions w hich are bigger than 0.6, so the effects of cutting speed on the PCBN tool are m u
