Certain non-metallic granules （NMG） were selected as the research object. It was proposed to conduct the volume compression experiments as well as those on the NMG physical properties at high stress levels. Then, no...Certain non-metallic granules （NMG） were selected as the research object. It was proposed to conduct the volume compression experiments as well as those on the NMG physical properties at high stress levels. Then, not only the volume compression ratio curve but also the extended Drucker-Prager linear model were obtained. In addition, through the friction strength tests, parameters of the Mohr-Coulomb model were gained, which proved in basic agreement with those of the extended Drucker-Prager linear model. Additionally, curves of the friction coefficients between the NMG and the sheet metal trader different pressures were also obtained. Based on the material performance experiments, numerical analysis in respect of flexible-die forming process with solid granule medium （SGM） was conducted. The die and device for experiments of solid granule medium forming （SGMF） on sheet metal were designed and manufactured. Typical parabolic parts were successfully trial-produced. The tests and simulation results show that the sheet formability is significantly improved for the extraordinary friction performance during interaction between the SGM and the sheet metal surface. The process control and die structure are simple, and the shaped work-pieces enjoy many advantages, such as satisfactory surface quality and favorable die fitability, which offers a brand-new method and means for processing and preparation of sheet metals.展开更多
基于NUMISHEET 2002会议提出的杯形件拉深Benchmark试验方案,在5和30 k N两种压边力工况下,对2 mm厚2024铝合金板料的拉深性能、凸耳现象、回弹现象及板厚变化进行试验研究,采用DYNAFORM软件对拉深过程进行有限元仿真。试验和仿真结果...基于NUMISHEET 2002会议提出的杯形件拉深Benchmark试验方案,在5和30 k N两种压边力工况下,对2 mm厚2024铝合金板料的拉深性能、凸耳现象、回弹现象及板厚变化进行试验研究,采用DYNAFORM软件对拉深过程进行有限元仿真。试验和仿真结果比较表明,在两种不同压边力工况下,2024铝合金具有较好的拉深性能,拉深件均出现凸耳、回弹及板料厚度变化不均等现象。在与板料轧制方向成0°、90°、180°和270°产生了4个凸耳;在低压边力工况下,与板料轧制方向垂直方向回弹量最大,为3.14%;随着凸模行程的增加,拉深力增大,当凸模行程为26 mm时,拉深力呈平缓趋势。展开更多
The experimental die apparatus of the solid granules medium forming on sheet metal was designed and manufactured.Typical parts,such as conical,parabolic,cylindrical and square-box-shaped components,were successfully t...The experimental die apparatus of the solid granules medium forming on sheet metal was designed and manufactured.Typical parts,such as conical,parabolic,cylindrical and square-box-shaped components,were successfully trial-produced as well.According to the analysis of the changing trends of the cross-section shape and the wall thickness during the process,it can be found that the shape of the free deformation zone of the sheet metal,which is the most critical thinning area,can be described as an approximately spherical cap.According to this forming feature,back pressure deep drawing technology with solid granules medium on sheet metal was proposed to restrain drastic thinning at the bottom of the part through the joint friction effect of solid granules medium,the back pressure tringle and the sheet metal.Therefore,the deep drawing limit of the sheet metal is significantly improved.In order to fabricate thin-walled rotary parts with great drawing ratio and complex cross-sections,a finite element model based on the material property test of the solid granules medium was established to optimize the scheme of the back pressure deep drawing.The effects on the forming performance of sheet metal from back pressure load and the approach of blank holding control were analyzed through this model.展开更多
Major defects in forming of conical cups are wrinkles and rupture.Hydrodynamic deep drawing assisted by radial pressure（HDDRP） is a sheet hydroforming process for production of shell cups in one step.In this work,pr...Major defects in forming of conical cups are wrinkles and rupture.Hydrodynamic deep drawing assisted by radial pressure（HDDRP） is a sheet hydroforming process for production of shell cups in one step.In this work,process window diagrams（PWDs） for Al1050-O,pure copper and DIN 1623 St14 steel are obtained for HDDRP process.The PWD is determined to provide a quick assessment of part producibility for sheet hydroforming process.Finite element method is used for this purpose considering the process parameters including pressure path,and the blank material and its thickness.Numerical results are validated by experiments.It is shown that the sheets with less initial thickness and higher strength show better formability and uniformity of thickness distribution on final product.The results demonstrate that the obtained PWD can predict appropriate forming area and probability of rupture or wrinkling occurrence under different pressure loading paths.展开更多
In this study,a numerical analysis was conducted on the ductile fracture of a 2-mm diameter Mg-1Zn-0.5Mn-0.5Sr-0.1Ca alloy wire during drawing.The hexagonally close-packed crystal structure of Mg alloys causes asymmet...In this study,a numerical analysis was conducted on the ductile fracture of a 2-mm diameter Mg-1Zn-0.5Mn-0.5Sr-0.1Ca alloy wire during drawing.The hexagonally close-packed crystal structure of Mg alloys causes asymmetric fracture behavior,especially in the compression region.The aim of this study is to develop a comprehensive damage model for Mg alloy wire that accurately predicts ductile fracture,with a focus on the compression region.A novel experimental method was introduced to measure the ductile fracture of Mg alloy wires under different stress states.The wire drawing process was simulated using the Generalized Incremental Stress-State dependent damage(GISSMO)Model and the Semi-Analytical Model for Polymers(SAMP)model.The damage model's prediction and the experimental results were found to be in excellent agreement,especially in determining crack initiation.Computational analysis established a safe zone diagram for die angle and reduction ratio,and experimental validation confirmed the feasibility of this approach.The proposed damage model can provide a practical and reliable analysis for optimizing the drawing process of Mg alloy wire.展开更多
This study introduces an innovative theoretical model critical for predicting stress and strain distributions in Ti/Al bi-metal sheet production and its subsequent deep drawing process.Grounded in extensive mechanical...This study introduces an innovative theoretical model critical for predicting stress and strain distributions in Ti/Al bi-metal sheet production and its subsequent deep drawing process.Grounded in extensive mechanical and geometric analysis,the model facilitates manufacturing process optimization and the production of high-quality components.Finite Element Method(FEM)simulations are integrated to examine the significant effects of die geometric parameters on metal flow dynamics and susceptibility to material stress.The model's precision is enhanced by incorporating anisotropic material properties and cohesive zone models.A rigorous experimental framework validates the model,highlighting the practical utility of optimized parameters in Ti/Al bimetal component fabrication.Additionally,uniaxial tensile tests using the Video Image Correlation-3D(VIC-3D)system provide detailed insights into material deformation,elucidating stress distribution and metal flow in composite layers.Thus,the research presents a refined methodology for the efficient production of Ti/Al bi-metal components,offering valuable knowledge transferable to various materials and processing scenarios.The findings of this work are expected to make a significant impact on material engineering and mechanical manufacturing.展开更多
A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micr...A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.展开更多
基金Project(50775197)supported by the National Natural Science Foundation of China
文摘Certain non-metallic granules （NMG） were selected as the research object. It was proposed to conduct the volume compression experiments as well as those on the NMG physical properties at high stress levels. Then, not only the volume compression ratio curve but also the extended Drucker-Prager linear model were obtained. In addition, through the friction strength tests, parameters of the Mohr-Coulomb model were gained, which proved in basic agreement with those of the extended Drucker-Prager linear model. Additionally, curves of the friction coefficients between the NMG and the sheet metal trader different pressures were also obtained. Based on the material performance experiments, numerical analysis in respect of flexible-die forming process with solid granule medium （SGM） was conducted. The die and device for experiments of solid granule medium forming （SGMF） on sheet metal were designed and manufactured. Typical parabolic parts were successfully trial-produced. The tests and simulation results show that the sheet formability is significantly improved for the extraordinary friction performance during interaction between the SGM and the sheet metal surface. The process control and die structure are simple, and the shaped work-pieces enjoy many advantages, such as satisfactory surface quality and favorable die fitability, which offers a brand-new method and means for processing and preparation of sheet metals.
基金Project(50775197) supported by the National Natural Science Foundation of China
文摘The experimental die apparatus of the solid granules medium forming on sheet metal was designed and manufactured.Typical parts,such as conical,parabolic,cylindrical and square-box-shaped components,were successfully trial-produced as well.According to the analysis of the changing trends of the cross-section shape and the wall thickness during the process,it can be found that the shape of the free deformation zone of the sheet metal,which is the most critical thinning area,can be described as an approximately spherical cap.According to this forming feature,back pressure deep drawing technology with solid granules medium on sheet metal was proposed to restrain drastic thinning at the bottom of the part through the joint friction effect of solid granules medium,the back pressure tringle and the sheet metal.Therefore,the deep drawing limit of the sheet metal is significantly improved.In order to fabricate thin-walled rotary parts with great drawing ratio and complex cross-sections,a finite element model based on the material property test of the solid granules medium was established to optimize the scheme of the back pressure deep drawing.The effects on the forming performance of sheet metal from back pressure load and the approach of blank holding control were analyzed through this model.
文摘Major defects in forming of conical cups are wrinkles and rupture.Hydrodynamic deep drawing assisted by radial pressure（HDDRP） is a sheet hydroforming process for production of shell cups in one step.In this work,process window diagrams（PWDs） for Al1050-O,pure copper and DIN 1623 St14 steel are obtained for HDDRP process.The PWD is determined to provide a quick assessment of part producibility for sheet hydroforming process.Finite element method is used for this purpose considering the process parameters including pressure path,and the blank material and its thickness.Numerical results are validated by experiments.It is shown that the sheets with less initial thickness and higher strength show better formability and uniformity of thickness distribution on final product.The results demonstrate that the obtained PWD can predict appropriate forming area and probability of rupture or wrinkling occurrence under different pressure loading paths.
基金supported by the National Research Foundation of Korea(NRF)grant funded by the Korea government(MSIT)(Nos.2020R1A2C2010986,2022M3H4A1A04085301)。
文摘In this study,a numerical analysis was conducted on the ductile fracture of a 2-mm diameter Mg-1Zn-0.5Mn-0.5Sr-0.1Ca alloy wire during drawing.The hexagonally close-packed crystal structure of Mg alloys causes asymmetric fracture behavior,especially in the compression region.The aim of this study is to develop a comprehensive damage model for Mg alloy wire that accurately predicts ductile fracture,with a focus on the compression region.A novel experimental method was introduced to measure the ductile fracture of Mg alloy wires under different stress states.The wire drawing process was simulated using the Generalized Incremental Stress-State dependent damage(GISSMO)Model and the Semi-Analytical Model for Polymers(SAMP)model.The damage model's prediction and the experimental results were found to be in excellent agreement,especially in determining crack initiation.Computational analysis established a safe zone diagram for die angle and reduction ratio,and experimental validation confirmed the feasibility of this approach.The proposed damage model can provide a practical and reliable analysis for optimizing the drawing process of Mg alloy wire.
基金supported by the National Natural Science Foundation of China(No.52005432,51674222)the Natural Science Foundation of Hebei Province of Iron and Steel Research(No.E2021203179)+1 种基金the Chinese Post-doctoral Science Foundation(No.2020M680904)the Foundation of Hebei Province Post-Doctoral Preferred Project(No.B2020003011)。
文摘This study introduces an innovative theoretical model critical for predicting stress and strain distributions in Ti/Al bi-metal sheet production and its subsequent deep drawing process.Grounded in extensive mechanical and geometric analysis,the model facilitates manufacturing process optimization and the production of high-quality components.Finite Element Method(FEM)simulations are integrated to examine the significant effects of die geometric parameters on metal flow dynamics and susceptibility to material stress.The model's precision is enhanced by incorporating anisotropic material properties and cohesive zone models.A rigorous experimental framework validates the model,highlighting the practical utility of optimized parameters in Ti/Al bimetal component fabrication.Additionally,uniaxial tensile tests using the Video Image Correlation-3D(VIC-3D)system provide detailed insights into material deformation,elucidating stress distribution and metal flow in composite layers.Thus,the research presents a refined methodology for the efficient production of Ti/Al bi-metal components,offering valuable knowledge transferable to various materials and processing scenarios.The findings of this work are expected to make a significant impact on material engineering and mechanical manufacturing.
基金the National Natural Science Foundation of China(Nos.U21A2051,52173297,52071133)the R&D Projects of Henan Academy of Sciences of China(No.220910009)+2 种基金the Key R&D and Promotion Projects of Henan Province of China(No.212102210441)the Joint Fund of Henan Science and Technology R&D Plan of China(No.222103810037)the Zhongyuan Scholar Workstation Funded Project of China(No.214400510028).
文摘A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.
