Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-...Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-quality metal parts by WAAM,several problems about the heat build-up,the deposit-path optimization,and the stability of the process parameters need to be well addressed.To overcome these issues,a new WAAM method based on the double electrode micro plasma arc welding(DE-MPAW)was designed.The circuit principles of different metal-transfer models in the DE-MPAW deposition process were analyzed theoretically.The effects between the parameters,wire feed rate and torch stand-off distance,in the process of WAAM were investigated experimentally.In addition,a real-time DE-MPAW control system was developed to optimize and stabilize the deposition process by self-adaptively changing the wire feed rate and torch stand-off distance.Finally,a series of tests were performed to evaluate the control system’s performance.The results show that the capability against interferences in the process of WAAM has been enhanced by this self-adaptive adjustment system.Further,the deposition paths about the metal part’s layer heights in WAAM are simplified.Finally,the appearance of the WAAM-deposited metal layers is also improved with the use of the control system.展开更多
实现铝钢良好连接的关键是有效控制焊接热输入,尽量降低中间层铝铁金属间化合物的厚度,一般认为中间层金属间化合物厚度小于10μm时铝钢接头质量良好。提出旁路耦合电弧熔钎焊方法,通过调节旁路电弧电流的大小来控制焊接热输入。在优化...实现铝钢良好连接的关键是有效控制焊接热输入,尽量降低中间层铝铁金属间化合物的厚度,一般认为中间层金属间化合物厚度小于10μm时铝钢接头质量良好。提出旁路耦合电弧熔钎焊方法,通过调节旁路电弧电流的大小来控制焊接热输入。在优化控制系统和工艺参数的基础上采用脉冲旁路耦合电弧焊方法将铝镁合金ER5356堆焊到304不锈钢板上,获得结合良好的焊缝。对焊接接头进行扫描电镜(Scanning electron microscope,SEM)、能量色散光谱仪(Energy dispersive spectrometry,EDS)分析,结果表明:铝与不锈钢焊接接头中间层金属间化合物平均厚度约为8μm,小于10μm的临界厚度;脉冲旁路耦合电弧焊方法能够实现铝钢的连接,是一种新型低成本低热输入电弧焊方法。展开更多
在介绍了双丝旁路耦合电弧熔化极气体保护焊(双丝旁路耦合电弧(Double-electrode gas metal arc welding,DE-GMAW))高效焊接工艺原理的基础之上,采用双闭环反馈解耦智能控制系统,进行双丝旁路耦合电弧GMAW高速焊接工艺试验,测量双丝旁...在介绍了双丝旁路耦合电弧熔化极气体保护焊(双丝旁路耦合电弧(Double-electrode gas metal arc welding,DE-GMAW))高效焊接工艺原理的基础之上,采用双闭环反馈解耦智能控制系统,进行双丝旁路耦合电弧GMAW高速焊接工艺试验,测量双丝旁路耦合电弧GMAW母材热输入,分析双丝旁路耦合电弧GMAW高效焊接工艺机理,并对双丝旁路耦合电弧GMAW高效焊接工艺方法进行改进,进一步研究混合气体保护下的双丝旁路耦合电弧GMAW及其熔滴过渡行为,且开发出单电源双丝旁路耦合电弧GMAW。研究表明:采用双闭环反馈解耦智能控制系统使双丝旁路耦合电弧GMAW焊接过程稳定性更好、精确度更高且响应速度更快;旁路分流是实现高效焊接的同时降低母材热输入的关键;采用混合气体保护下的双丝旁路耦合电弧GMAW能进一步提高焊接过程稳定性,单电源双丝旁路耦合电弧GMAW能形成良好的焊缝成形,且设备成本低。展开更多
In view of the unstable welding process of Tri-Arc DE,surfacing test with Q235 steel plate was completed with the help of the self-built high-speed camera and waveform synchronous acquisition system using the Tri-Arc ...In view of the unstable welding process of Tri-Arc DE,surfacing test with Q235 steel plate was completed with the help of the self-built high-speed camera and waveform synchronous acquisition system using the Tri-Arc DE technology. The effects of pulsed M-Arc frequency on Tri-Arc DE droplet transfer and weld formation were analyzed. The results show that while the gradual increase of pulse frequency,the droplet transfer frequency gradually decreases,which is followed by several drops per pulse,one drop per pulse,and one drop within several pulses. The most ideal transfer form is one drop per pulse,of which the welding process is the most stable,and the quality of weld formation is the most satisfied.展开更多
Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,t...Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,they can not precisely control the heat input to work-piece,they are high costs,low efficiency and consist lots of complex welding devices,and the generated intermetallic compound layer in weld bead interface is thicker.A novel pulsed double electrode gas metal arc welding（Pulsed DE-GMAW）method is developed.To achieve a stable welding process for joining of aluminum to steel,a mathematical model of coupled arc is established,and a new control scheme that uses the average feedback arc voltage of main loop to adjust the wire feed speed to control coupled arc length is proposed and developed.Then,the impulse control simulation of coupled arc length,wire feed speed and wire extension is conducted to demonstrate the mathematical model and predict the stability of welding process by changing the distance of contact tip to work-piece（CTWD）.To prove the proposed PSO based PID control scheme’s feasibility,the rapid prototyping experimental system is setup and the bead-on-plate control experiments are conducted to join aluminum to steel.The impulse control simulation shows that the established model can accurately represent the variation of coupled arc length,wire feed speed and the average main arc voltage when the welding process is disturbed,and the developed controller has a faster response and adjustment,only runs about 0.1 s.The captured electric signals show the main arc voltage gradually closes to the supposed arc voltage by adjusting the wire feed speed in 0.8 s.The obtained typical current waveform demonstrates that the main current can be reduced by controlling the bypass current under maintaining a relative large total current.The control experiment proves the accuracy of proposed model and feasibility of new control scheme further.The beautiful and smooth weld beads are also obtained by t展开更多
Double-electrode gas shielded arc welding （ DE - GMAW） was used to weld the magnesium alloy cylinder with the diameter of 200 mm and the thickness of 6 mm. In order to study the residual stress distribution of AZ31B...Double-electrode gas shielded arc welding （ DE - GMAW） was used to weld the magnesium alloy cylinder with the diameter of 200 mm and the thickness of 6 mm. In order to study the residual stress distribution of AZ31B magnesiunl alloy welding point, numerical sinmlation of welding temperature field, stress field and residual stress were carried out by MSC. mare software. The results show that the residual stress in the weld and the heat affected zone is large, and with the increase of the distance away from the weld center, the residual stress decreases. In most areas, the longitudinal residual stress is greater than the transverse residual stress （except for the inside and outside surfaces of the weld） , all of which provides theoretical support for the study of magnesiunl alloy welding residual stress.展开更多
The action of the composite heat source model in DE-GMAW has been carried out according to the characteristics of the DE-GMA W process, and the distribution of surface and body heat source was analyzed. The weld tempe...The action of the composite heat source model in DE-GMAW has been carried out according to the characteristics of the DE-GMA W process, and the distribution of surface and body heat source was analyzed. The weld temperature field distribution has been derived from the appropriate boundary conditions and the thermal physical property parameters by COMSOL software. The effects of the positions of the surface and body heat source on the cross- sectional shape were investigated by studying the experimental welding thermal cycle curve. The simulated results are fully compliant with the experimental data under the same conditions. This illustrates that the composite heat source model is correct. It reflects the thermal mechanism of DE-GMA W process, and reveals the internal influence of weld shaping.展开更多
基金Supported by National Natural Science Foundation of China(Grant No.51665034).
文摘Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-quality metal parts by WAAM,several problems about the heat build-up,the deposit-path optimization,and the stability of the process parameters need to be well addressed.To overcome these issues,a new WAAM method based on the double electrode micro plasma arc welding(DE-MPAW)was designed.The circuit principles of different metal-transfer models in the DE-MPAW deposition process were analyzed theoretically.The effects between the parameters,wire feed rate and torch stand-off distance,in the process of WAAM were investigated experimentally.In addition,a real-time DE-MPAW control system was developed to optimize and stabilize the deposition process by self-adaptively changing the wire feed rate and torch stand-off distance.Finally,a series of tests were performed to evaluate the control system’s performance.The results show that the capability against interferences in the process of WAAM has been enhanced by this self-adaptive adjustment system.Further,the deposition paths about the metal part’s layer heights in WAAM are simplified.Finally,the appearance of the WAAM-deposited metal layers is also improved with the use of the control system.
文摘实现铝钢良好连接的关键是有效控制焊接热输入,尽量降低中间层铝铁金属间化合物的厚度,一般认为中间层金属间化合物厚度小于10μm时铝钢接头质量良好。提出旁路耦合电弧熔钎焊方法,通过调节旁路电弧电流的大小来控制焊接热输入。在优化控制系统和工艺参数的基础上采用脉冲旁路耦合电弧焊方法将铝镁合金ER5356堆焊到304不锈钢板上,获得结合良好的焊缝。对焊接接头进行扫描电镜(Scanning electron microscope,SEM)、能量色散光谱仪(Energy dispersive spectrometry,EDS)分析,结果表明:铝与不锈钢焊接接头中间层金属间化合物平均厚度约为8μm,小于10μm的临界厚度;脉冲旁路耦合电弧焊方法能够实现铝钢的连接,是一种新型低成本低热输入电弧焊方法。
文摘在介绍了双丝旁路耦合电弧熔化极气体保护焊(双丝旁路耦合电弧(Double-electrode gas metal arc welding,DE-GMAW))高效焊接工艺原理的基础之上,采用双闭环反馈解耦智能控制系统,进行双丝旁路耦合电弧GMAW高速焊接工艺试验,测量双丝旁路耦合电弧GMAW母材热输入,分析双丝旁路耦合电弧GMAW高效焊接工艺机理,并对双丝旁路耦合电弧GMAW高效焊接工艺方法进行改进,进一步研究混合气体保护下的双丝旁路耦合电弧GMAW及其熔滴过渡行为,且开发出单电源双丝旁路耦合电弧GMAW。研究表明:采用双闭环反馈解耦智能控制系统使双丝旁路耦合电弧GMAW焊接过程稳定性更好、精确度更高且响应速度更快;旁路分流是实现高效焊接的同时降低母材热输入的关键;采用混合气体保护下的双丝旁路耦合电弧GMAW能进一步提高焊接过程稳定性,单电源双丝旁路耦合电弧GMAW能形成良好的焊缝成形,且设备成本低。
基金Project was supported by the National Natural Science Foundation of China(Grant No.U1733125)Natural Science Foundation of Tianjin(Grant No.18JCYBJC19100,18JCYJC18700)
文摘In view of the unstable welding process of Tri-Arc DE,surfacing test with Q235 steel plate was completed with the help of the self-built high-speed camera and waveform synchronous acquisition system using the Tri-Arc DE technology. The effects of pulsed M-Arc frequency on Tri-Arc DE droplet transfer and weld formation were analyzed. The results show that while the gradual increase of pulse frequency,the droplet transfer frequency gradually decreases,which is followed by several drops per pulse,one drop per pulse,and one drop within several pulses. The most ideal transfer form is one drop per pulse,of which the welding process is the most stable,and the quality of weld formation is the most satisfied.
基金Supported by National Natural Science Foundation of China(Grant No.51165023)Project of International Cooperation and Exchanges of National Natural Science Foundation of China(Grant No.51210105024)+1 种基金Financial Commission of Gansu Province of Chinathe Hong Liu Outstanding Talent Training Plan of Lanzhou University of Technology,China(Grant No.J201201)
文摘Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,they can not precisely control the heat input to work-piece,they are high costs,low efficiency and consist lots of complex welding devices,and the generated intermetallic compound layer in weld bead interface is thicker.A novel pulsed double electrode gas metal arc welding（Pulsed DE-GMAW）method is developed.To achieve a stable welding process for joining of aluminum to steel,a mathematical model of coupled arc is established,and a new control scheme that uses the average feedback arc voltage of main loop to adjust the wire feed speed to control coupled arc length is proposed and developed.Then,the impulse control simulation of coupled arc length,wire feed speed and wire extension is conducted to demonstrate the mathematical model and predict the stability of welding process by changing the distance of contact tip to work-piece（CTWD）.To prove the proposed PSO based PID control scheme’s feasibility,the rapid prototyping experimental system is setup and the bead-on-plate control experiments are conducted to join aluminum to steel.The impulse control simulation shows that the established model can accurately represent the variation of coupled arc length,wire feed speed and the average main arc voltage when the welding process is disturbed,and the developed controller has a faster response and adjustment,only runs about 0.1 s.The captured electric signals show the main arc voltage gradually closes to the supposed arc voltage by adjusting the wire feed speed in 0.8 s.The obtained typical current waveform demonstrates that the main current can be reduced by controlling the bypass current under maintaining a relative large total current.The control experiment proves the accuracy of proposed model and feasibility of new control scheme further.The beautiful and smooth weld beads are also obtained by t
文摘Double-electrode gas shielded arc welding （ DE - GMAW） was used to weld the magnesium alloy cylinder with the diameter of 200 mm and the thickness of 6 mm. In order to study the residual stress distribution of AZ31B magnesiunl alloy welding point, numerical sinmlation of welding temperature field, stress field and residual stress were carried out by MSC. mare software. The results show that the residual stress in the weld and the heat affected zone is large, and with the increase of the distance away from the weld center, the residual stress decreases. In most areas, the longitudinal residual stress is greater than the transverse residual stress （except for the inside and outside surfaces of the weld） , all of which provides theoretical support for the study of magnesiunl alloy welding residual stress.
基金supported by the National Natural Science Foundation of China(Grant No.51165023)
文摘The action of the composite heat source model in DE-GMAW has been carried out according to the characteristics of the DE-GMA W process, and the distribution of surface and body heat source was analyzed. The weld temperature field distribution has been derived from the appropriate boundary conditions and the thermal physical property parameters by COMSOL software. The effects of the positions of the surface and body heat source on the cross- sectional shape were investigated by studying the experimental welding thermal cycle curve. The simulated results are fully compliant with the experimental data under the same conditions. This illustrates that the composite heat source model is correct. It reflects the thermal mechanism of DE-GMA W process, and reveals the internal influence of weld shaping.
