采用喷射沉积法制备15%(体积分数)4.5 m SiCp/Al-20Si复合材料及其基体合金,研究该组材料的微观组织、力学性能、高周疲劳性能以及疲劳断口形貌。结果表明:SiC颗粒的加入有利于提高材料的力学性能;复合材料及其基体的高调疲劳寿命随应...采用喷射沉积法制备15%(体积分数)4.5 m SiCp/Al-20Si复合材料及其基体合金,研究该组材料的微观组织、力学性能、高周疲劳性能以及疲劳断口形貌。结果表明:SiC颗粒的加入有利于提高材料的力学性能;复合材料及其基体的高调疲劳寿命随应力幅值的减小而增加,在相同应力幅值下,复合材料的疲劳寿命远远高于基体合金。疲劳裂纹从大颗粒的初晶Si的断裂以及Si相脱离处形核,并开始扩展。对于复合材料而言,SiC颗粒尺寸较小,不容易发生断裂,在形核过程中,当裂纹遇到SiC颗粒时,裂纹或者避开增强体,或者受阻于SiC颗粒,只能在基体合金中扩展,从而扩大了疲劳形核区的面积,提高了材料的疲劳寿命。Si颗粒的脱离、Si相的断裂以及SiC颗粒与基体界面的脱粘是复合材料疲劳断裂失效的主要机制。展开更多
Cu-P-silicon carbide （SiC） composite coatings were deposited by means of electroless plating.The effects of pH values,temperature,and different concentrations of sodium hypophosphite （NaH2PO2·H2O）,nickel sulf...Cu-P-silicon carbide （SiC） composite coatings were deposited by means of electroless plating.The effects of pH values,temperature,and different concentrations of sodium hypophosphite （NaH2PO2·H2O）,nickel sulfate （NiSO4·6H2O）,sodium citrate （C6H5Na3O7·2H2O） and SiC on the deposition rate and coating compositions were evaluated,and the bath formulation for Cu-P-SiC composite coatings was optimised.The coating compositions were determined using energy-dispersive X-ray analysis （EDX）.The corresponding optimal operating parameters for depositing Cu-P-SiC are as follows：pH 9;temperature,90oC;NaH2PO2·H2O concentration,125 g/L;NiSO4·6H2O concentration,3.125 g/L;SiC concentration,5 g/L;and C6H5Na3O7·2H2O concentration,50 g/L.The surface morphology of the coatings analysed by scanning electron microscopy （SEM） shows that Cu particles are uniformly distributed.The hardness and wear resistance of Cu-P composite coatings are improved with the addition of SiC particles and increase with the increase of SiC content.展开更多
To improve the hydrophilicity and anti-fouling performance in water treatment,both entrapped method and deposited method were used to modify polyvinylidene fluoride(PVDF)porous membrane with composite Al2O3/TiO2 nano-...To improve the hydrophilicity and anti-fouling performance in water treatment,both entrapped method and deposited method were used to modify polyvinylidene fluoride(PVDF)porous membrane with composite Al2O3/TiO2 nano-particles.Neat PVDF membrane was prepared and its property was also compared with that of the modified membranes.Membrane permeation flux and anti-fouling performance were measured using a membrane cell.The contact angle between water and membrane surface was detected in order to denote the membrane hydrophilicity.Membrane morphology and surface structure were examined by atomic-force microscopy(AFM)and scanning electron microscopy(SEM).Experimental results showed that modified membranes had higher permeation fluxes than that of the neat PVDF membrane.The addition of nano-particles altered membrane surface morphology and increased surface roughness.Due to the hydrophilicity of nano-particles,however,the membrane anti-fouling performance was improved instead of worsened.The entrapped membrane exhibited better anti-fouling performance than the deposited membrane and the neat membrane.展开更多
The recently discovered nitrate ore field in the Turpan-Hami Basin of western China represents an estimated resource of 2.5 billion tons, and is comparable in scale to the Atacama Desert super-scale nitrate deposit in...The recently discovered nitrate ore field in the Turpan-Hami Basin of western China represents an estimated resource of 2.5 billion tons, and is comparable in scale to the Atacama Desert super-scale nitrate deposit in Chile. The research on this area is rarely carried out, and the origin of the deposits remains uncertain. In this study, new methods were used to systematically analyze N and O isotopes in nitrate minerals collected from the Kumutage, Xiaocaohu, Wuzongbulak, Dawadi, Tuyugou, and Shaer ore deposits in the Turpan-Hami Basin. The data showed that the δ15NAir value ranges from 0.7‰ to 27.6‰, but mostly between 2‰ and 6‰, which was similar to atmospheric NO3-. The 18O was highly enriched with δ18OV-SMOW varying from 30.2‰ to 46.7‰. This differs from levels in deposits derived from microbial nitrogen fixation, but is similar to those in atmospheric nitrates. N and O isotopes data indicated that nitrate deposits in Turpan-Hami Basin must be the result of deposition of atmospheric nitrate particles. Although atmospheric nitrate particles are common, the nitrate deposits could form only under the condition of long-term extreme drought climate and very limited biological activity. This paper summarized the ore-forming mechanism of different types nitrate deposits based on their geological setting.展开更多
PM 10 airborne particles and soot deposit collected after a fire incident at a chemical store were analyzed in order to determine the concentrations of polycyclic aromatic hydrocarbons(PAHs). The samples were ext...PM 10 airborne particles and soot deposit collected after a fire incident at a chemical store were analyzed in order to determine the concentrations of polycyclic aromatic hydrocarbons(PAHs). The samples were extracted with 1∶1 hexane-dichloromethane by ultrasonic agitation. The extracts were then subjected to gas chromatography-mass spectrometric(GC-MS) analysis. The total PAHs concentrations in airborne particles and soot deposit were found to be 3.27±1.55 ng/m 3 and 12.81±24.37 μg/g, respectively. Based on the molecular distributions of PAHs and the interpretation of their diagnostic ratios such as PHEN/(PHEN + ANTH), FLT/(FLT + PYR) and BeP/(BeP + BaP), PAHs in both airborne particles and soot deposit may be inferred to be from the same source. The difference in the value of IP/(IP + BgP) for these samples indicated that benzo[g,h,i]perylene and coronene tend to be attached to finer particles and reside in the air for longer periods. Comparison between the molecular distributions of PAHs and their diagnostic ratios observed in the current study with those reported for urban atmospheric and roadside soil particles revealed that they are of different sources.展开更多
This research assesses the speed of saline fluid in vein vessels using venipuncture medical kit as well as DC submersive pumps that are being controlled by a microcontroller. The microcontroller is monitored and gover...This research assesses the speed of saline fluid in vein vessels using venipuncture medical kit as well as DC submersive pumps that are being controlled by a microcontroller. The microcontroller is monitored and governed using a software IDE interface installed on a powerful laptop. Saline solution is being pumped through a medical syringe at variable speeds up to a maximum of 18.39 cm/second to the vein. The novel technique in this research is the usage of two pumps called Pump 1 and Pump 2. Pump 1 is used to physically model the flow of “blood” in human vein and the second pump (Pump 2) is used to generate the accelerated saline particles that are used to break the yellow grease that is placed on the inside of the vein’s wall. A tiny brush is briefly dipped into yellow grease, and then it is used to place one layer (one turn) of yellow grease on the inside of the vein’s wall, and then this procedure is repeated to place consecutive layers of yellow grease onto the inside of the wall of the vein vessel using a tiny brush. It was found that accelerated saline particles can in fact destroy fats that are built up inside the veins’ walls.展开更多
Geogas prospecting is a new method in the search for deep and/or concealed mineral deposits.The probing depth of the method comes to 300-500 m below the surface. The method, based on nuclear aualysis and accumulation ...Geogas prospecting is a new method in the search for deep and/or concealed mineral deposits.The probing depth of the method comes to 300-500 m below the surface. The method, based on nuclear aualysis and accumulation sampling, has matured and become useful method of geogas prospecting, through authors' studies more than 10 years. The study of the mechanism for geogas prospecting has also been progressed. It bas been revealed that the geogas matter is in the form of nano-scale particles of the ores by the observation of scanning electron microscope (SEM). This paper summarizes the feature of the geogas anomaly, and describes its forming mechanism. A new example using geogas prospecting is given.展开更多
文摘采用喷射沉积法制备15%(体积分数)4.5 m SiCp/Al-20Si复合材料及其基体合金,研究该组材料的微观组织、力学性能、高周疲劳性能以及疲劳断口形貌。结果表明:SiC颗粒的加入有利于提高材料的力学性能;复合材料及其基体的高调疲劳寿命随应力幅值的减小而增加,在相同应力幅值下,复合材料的疲劳寿命远远高于基体合金。疲劳裂纹从大颗粒的初晶Si的断裂以及Si相脱离处形核,并开始扩展。对于复合材料而言,SiC颗粒尺寸较小,不容易发生断裂,在形核过程中,当裂纹遇到SiC颗粒时,裂纹或者避开增强体,或者受阻于SiC颗粒,只能在基体合金中扩展,从而扩大了疲劳形核区的面积,提高了材料的疲劳寿命。Si颗粒的脱离、Si相的断裂以及SiC颗粒与基体界面的脱粘是复合材料疲劳断裂失效的主要机制。
基金supported by Universiti Sains Malaysia under the Research University Grant (RU. Grant No.1001/PKIMIA/811006)
文摘Cu-P-silicon carbide （SiC） composite coatings were deposited by means of electroless plating.The effects of pH values,temperature,and different concentrations of sodium hypophosphite （NaH2PO2·H2O）,nickel sulfate （NiSO4·6H2O）,sodium citrate （C6H5Na3O7·2H2O） and SiC on the deposition rate and coating compositions were evaluated,and the bath formulation for Cu-P-SiC composite coatings was optimised.The coating compositions were determined using energy-dispersive X-ray analysis （EDX）.The corresponding optimal operating parameters for depositing Cu-P-SiC are as follows：pH 9;temperature,90oC;NaH2PO2·H2O concentration,125 g/L;NiSO4·6H2O concentration,3.125 g/L;SiC concentration,5 g/L;and C6H5Na3O7·2H2O concentration,50 g/L.The surface morphology of the coatings analysed by scanning electron microscopy （SEM） shows that Cu particles are uniformly distributed.The hardness and wear resistance of Cu-P composite coatings are improved with the addition of SiC particles and increase with the increase of SiC content.
基金Sponsored by the National High Technology Research and Development Program of China(863 Program)(Grant No.2006AA06Z303)the National Natural Science Foundation of China(Grant No.50778050)+2 种基金the Key Projects in the National Science & Technology Pillar Program in the Eleventh Five-year Plan Period(Grant No.2006BAJ08B09)the National Creative Research Groups(Grant No.50821002)the Key Scientific and Technological Project of Heilongjiang Province(Grant No.GB06C20403)
文摘To improve the hydrophilicity and anti-fouling performance in water treatment,both entrapped method and deposited method were used to modify polyvinylidene fluoride(PVDF)porous membrane with composite Al2O3/TiO2 nano-particles.Neat PVDF membrane was prepared and its property was also compared with that of the modified membranes.Membrane permeation flux and anti-fouling performance were measured using a membrane cell.The contact angle between water and membrane surface was detected in order to denote the membrane hydrophilicity.Membrane morphology and surface structure were examined by atomic-force microscopy(AFM)and scanning electron microscopy(SEM).Experimental results showed that modified membranes had higher permeation fluxes than that of the neat PVDF membrane.The addition of nano-particles altered membrane surface morphology and increased surface roughness.Due to the hydrophilicity of nano-particles,however,the membrane anti-fouling performance was improved instead of worsened.The entrapped membrane exhibited better anti-fouling performance than the deposited membrane and the neat membrane.
基金supported by Basic Scientific Research Operation Cost of State-Leveled Public Welfare Scientific Research Courtyard (Grant No. K0926)National Natural Science Foundation of China (Grant Nos. 40543013, 40873003)Key Laboratory of Isotope Geology, Ministry of Land and Resources
文摘The recently discovered nitrate ore field in the Turpan-Hami Basin of western China represents an estimated resource of 2.5 billion tons, and is comparable in scale to the Atacama Desert super-scale nitrate deposit in Chile. The research on this area is rarely carried out, and the origin of the deposits remains uncertain. In this study, new methods were used to systematically analyze N and O isotopes in nitrate minerals collected from the Kumutage, Xiaocaohu, Wuzongbulak, Dawadi, Tuyugou, and Shaer ore deposits in the Turpan-Hami Basin. The data showed that the δ15NAir value ranges from 0.7‰ to 27.6‰, but mostly between 2‰ and 6‰, which was similar to atmospheric NO3-. The 18O was highly enriched with δ18OV-SMOW varying from 30.2‰ to 46.7‰. This differs from levels in deposits derived from microbial nitrogen fixation, but is similar to those in atmospheric nitrates. N and O isotopes data indicated that nitrate deposits in Turpan-Hami Basin must be the result of deposition of atmospheric nitrate particles. Although atmospheric nitrate particles are common, the nitrate deposits could form only under the condition of long-term extreme drought climate and very limited biological activity. This paper summarized the ore-forming mechanism of different types nitrate deposits based on their geological setting.
文摘PM 10 airborne particles and soot deposit collected after a fire incident at a chemical store were analyzed in order to determine the concentrations of polycyclic aromatic hydrocarbons(PAHs). The samples were extracted with 1∶1 hexane-dichloromethane by ultrasonic agitation. The extracts were then subjected to gas chromatography-mass spectrometric(GC-MS) analysis. The total PAHs concentrations in airborne particles and soot deposit were found to be 3.27±1.55 ng/m 3 and 12.81±24.37 μg/g, respectively. Based on the molecular distributions of PAHs and the interpretation of their diagnostic ratios such as PHEN/(PHEN + ANTH), FLT/(FLT + PYR) and BeP/(BeP + BaP), PAHs in both airborne particles and soot deposit may be inferred to be from the same source. The difference in the value of IP/(IP + BgP) for these samples indicated that benzo[g,h,i]perylene and coronene tend to be attached to finer particles and reside in the air for longer periods. Comparison between the molecular distributions of PAHs and their diagnostic ratios observed in the current study with those reported for urban atmospheric and roadside soil particles revealed that they are of different sources.
文摘This research assesses the speed of saline fluid in vein vessels using venipuncture medical kit as well as DC submersive pumps that are being controlled by a microcontroller. The microcontroller is monitored and governed using a software IDE interface installed on a powerful laptop. Saline solution is being pumped through a medical syringe at variable speeds up to a maximum of 18.39 cm/second to the vein. The novel technique in this research is the usage of two pumps called Pump 1 and Pump 2. Pump 1 is used to physically model the flow of “blood” in human vein and the second pump (Pump 2) is used to generate the accelerated saline particles that are used to break the yellow grease that is placed on the inside of the vein’s wall. A tiny brush is briefly dipped into yellow grease, and then it is used to place one layer (one turn) of yellow grease on the inside of the vein’s wall, and then this procedure is repeated to place consecutive layers of yellow grease onto the inside of the wall of the vein vessel using a tiny brush. It was found that accelerated saline particles can in fact destroy fats that are built up inside the veins’ walls.
文摘Geogas prospecting is a new method in the search for deep and/or concealed mineral deposits.The probing depth of the method comes to 300-500 m below the surface. The method, based on nuclear aualysis and accumulation sampling, has matured and become useful method of geogas prospecting, through authors' studies more than 10 years. The study of the mechanism for geogas prospecting has also been progressed. It bas been revealed that the geogas matter is in the form of nano-scale particles of the ores by the observation of scanning electron microscope (SEM). This paper summarizes the feature of the geogas anomaly, and describes its forming mechanism. A new example using geogas prospecting is given.
