The present study fabricated a series of capillary wicks for loop heat pipes (LHPs), using two different methods, the cold-pressing sintering and direct loose sintering, and experimentally investigated the effect of d...The present study fabricated a series of capillary wicks for loop heat pipes (LHPs), using two different methods, the cold-pressing sintering and direct loose sintering, and experimentally investigated the effect of different methods, compositions and sintering parameters on their properties in terms of porosity, permeability and pore radius. Porosity and pore radius were measured by the Archimedes method and Scanning Electron Microscope (SEM), respectively. Permeability of the wicks was compared by calculation using empirical equation. Results show that capillary wicks were successfully fabricated by using two different methods; the optimal capillary wick was found to be sintered at 650°C for 30 min, using direct loose sintering technique, with 90% nickel and 10% copper. The wicks could reach the porosity of 70.07% and the permeability of 10?13 m2 order, with mean pore radius of 0.54 μm.展开更多
Lithium heat pipes have broad applications in heat pipe cooling reactors and hypersonic vehicles owing to their ultra-high working temperature.In particular,when the length of the lithium heat pipe is ultra-long,the f...Lithium heat pipes have broad applications in heat pipe cooling reactors and hypersonic vehicles owing to their ultra-high working temperature.In particular,when the length of the lithium heat pipe is ultra-long,the flow and heat transfer characteristics are more complex.In this study,an improved lumped parameter model that considers the Marangoni effect,bending effect,and different vapor flow patterns and Mach numbers was developed.Thereafter,the proposed model was verified using the University of New Mexico’s Heat Pipe and HTPIPE models.Finally,the verified model was applied to simulate the steady-state operation of an ultra-long lithium heat pipe in a Heat PipeSegmented Thermoelectric Module Converters space reactor.Based on the results:(1)Vapor thermal resistance was dominant at low heating power and decreased with increasing heating power.The vapor flow inside the heat pipe developed from the laminar to the turbulent phase,whereas the liquid phase in the heat pipe was always laminar.(2)The vapor pressure drop caused by bending was approximately 22–23%of the total,and the bending effect on the liquid pressure drop could be ignored.(3)The Marangoni effect reduced the capillary limit by hindering the liquid reflux,especially at low vapor temperatures.Without considering the Marangoni effect,the capillary limit of the lithium heat pipe was overestimated by 9%when the vapor temperature was 1400 K.(4)The total thermal resistance of the heat pipe significantly increased with increasing adiabatic length when the vapor temperature was low.Further,the wick dryness increased with increasing adiabatic length at any vapor temperature.Such findings improve on current knowledge for the optimal design and safety analysis of a heat pipe reactor,which adopts ultra-long lithium heat pipes.展开更多
The possibility of mimicking desirable properties from nature accelerates material improvement and generates commercial interests. For heat pipe development, many attempts have been made in heat pipe wicks to enhance ...The possibility of mimicking desirable properties from nature accelerates material improvement and generates commercial interests. For heat pipe development, many attempts have been made in heat pipe wicks to enhance its capillary performance by mimicking biology. Constructing biporous, composite, or nanopillar wicks with aim of achieving hierarchical structure has been found in many studies. Mimicking beetle shell surface to obtain hybrid wettability shows biomimetic potential in heat pipe wicks. This paper firstly reviews some fundamental studies in biomimetics, establishing a general idea of surface wetting and capillary effect. MR/scanning of two live plants （Musa X Paradisiaca and Salix Flamingo） provides the possibility of visualising internal structures in vivo and obtaining rates of water transport in xylem vessels. In addition, by investigating the work inspired directly or indirectly from biomimetics, the role that biomimetics plays in modern heat pipe technology is revealed. Our innovation which syntheses a low level of hierarchical structure and integrates integral wicks for different heat pipe sections including evaporator, adiabatic, and condenser is introduced. Mathematical modelling in terms of capillary pressure and capillary rise rate to characterise such new structure is provided.展开更多
The disturbance, caused by the boiling Phenomena in the inverted meniscus ac evaporator, is of great importancein the normal operation of the CPL, especially When the heat load is low. By theoretical and experimental ...The disturbance, caused by the boiling Phenomena in the inverted meniscus ac evaporator, is of great importancein the normal operation of the CPL, especially When the heat load is low. By theoretical and experimental studies onthis issue, it shows that the evaporator of the CPL operates in a mode of boiling in the Wick. By solving a set ofmomentum equations, it concludes that, this kind of boiling Phenomena in the wick cause no notable negativeinfluence on the normal peiformance of the CPL, although there really edests some adVerse influence during theCPL start-up. Addihonally, the causes of the dry-out of the evaporator under low heat load are conducted in thepaper. The conclusions are verified by subsequent experiments. More details about the experiments are alsodescribed in the paper.展开更多
The steady laminar pipe flow of a suspension with a gas volume fraction ∅≤0.5 and small or intermediate bubble deformations in long, and straight sections of a circular pipe is calculated. The calcula...The steady laminar pipe flow of a suspension with a gas volume fraction ∅≤0.5 and small or intermediate bubble deformations in long, and straight sections of a circular pipe is calculated. The calculations are based on the constitutive equation that was originally derived for dilute emulsions and further developed for concentrated suspensions containing bubbles. In contrast to the literature, an analytical procedure is used to determine the solution of a pipe flow more accurately. The results are presented and discussed with respect to the Reynolds number Re and capillary number Ca. If Ca 1, a bubble suspension has a parabolic velocity profile indicating a Newtonian rheology. If Ca ≈1, two regimes of flow are observed in agreement with the literature;that is, an inner plug flow where deformation rates are low and an outer flow where deformation rates are high. These results imply that, if Ca ∅?and that, if Ca ≥1, the opposite effect occurs;that is, the Reynolds number Re increases with increasing gas volume fraction.展开更多
基金Supported by Shandong Provincial Program of Science and Technology Develop-ment(Grant No.2007GG1HZ06004)
文摘The present study fabricated a series of capillary wicks for loop heat pipes (LHPs), using two different methods, the cold-pressing sintering and direct loose sintering, and experimentally investigated the effect of different methods, compositions and sintering parameters on their properties in terms of porosity, permeability and pore radius. Porosity and pore radius were measured by the Archimedes method and Scanning Electron Microscope (SEM), respectively. Permeability of the wicks was compared by calculation using empirical equation. Results show that capillary wicks were successfully fabricated by using two different methods; the optimal capillary wick was found to be sintered at 650°C for 30 min, using direct loose sintering technique, with 90% nickel and 10% copper. The wicks could reach the porosity of 70.07% and the permeability of 10?13 m2 order, with mean pore radius of 0.54 μm.
基金the CASHIPS Director’s Fund(No.YZJJ2021QN36)the Key Research Program of the Chinese Academy of Sciences(No.ZDRW-KT-2019-1-0202).
文摘Lithium heat pipes have broad applications in heat pipe cooling reactors and hypersonic vehicles owing to their ultra-high working temperature.In particular,when the length of the lithium heat pipe is ultra-long,the flow and heat transfer characteristics are more complex.In this study,an improved lumped parameter model that considers the Marangoni effect,bending effect,and different vapor flow patterns and Mach numbers was developed.Thereafter,the proposed model was verified using the University of New Mexico’s Heat Pipe and HTPIPE models.Finally,the verified model was applied to simulate the steady-state operation of an ultra-long lithium heat pipe in a Heat PipeSegmented Thermoelectric Module Converters space reactor.Based on the results:(1)Vapor thermal resistance was dominant at low heating power and decreased with increasing heating power.The vapor flow inside the heat pipe developed from the laminar to the turbulent phase,whereas the liquid phase in the heat pipe was always laminar.(2)The vapor pressure drop caused by bending was approximately 22–23%of the total,and the bending effect on the liquid pressure drop could be ignored.(3)The Marangoni effect reduced the capillary limit by hindering the liquid reflux,especially at low vapor temperatures.Without considering the Marangoni effect,the capillary limit of the lithium heat pipe was overestimated by 9%when the vapor temperature was 1400 K.(4)The total thermal resistance of the heat pipe significantly increased with increasing adiabatic length when the vapor temperature was low.Further,the wick dryness increased with increasing adiabatic length at any vapor temperature.Such findings improve on current knowledge for the optimal design and safety analysis of a heat pipe reactor,which adopts ultra-long lithium heat pipes.
文摘The possibility of mimicking desirable properties from nature accelerates material improvement and generates commercial interests. For heat pipe development, many attempts have been made in heat pipe wicks to enhance its capillary performance by mimicking biology. Constructing biporous, composite, or nanopillar wicks with aim of achieving hierarchical structure has been found in many studies. Mimicking beetle shell surface to obtain hybrid wettability shows biomimetic potential in heat pipe wicks. This paper firstly reviews some fundamental studies in biomimetics, establishing a general idea of surface wetting and capillary effect. MR/scanning of two live plants （Musa X Paradisiaca and Salix Flamingo） provides the possibility of visualising internal structures in vivo and obtaining rates of water transport in xylem vessels. In addition, by investigating the work inspired directly or indirectly from biomimetics, the role that biomimetics plays in modern heat pipe technology is revealed. Our innovation which syntheses a low level of hierarchical structure and integrates integral wicks for different heat pipe sections including evaporator, adiabatic, and condenser is introduced. Mathematical modelling in terms of capillary pressure and capillary rise rate to characterise such new structure is provided.
文摘The disturbance, caused by the boiling Phenomena in the inverted meniscus ac evaporator, is of great importancein the normal operation of the CPL, especially When the heat load is low. By theoretical and experimental studies onthis issue, it shows that the evaporator of the CPL operates in a mode of boiling in the Wick. By solving a set ofmomentum equations, it concludes that, this kind of boiling Phenomena in the wick cause no notable negativeinfluence on the normal peiformance of the CPL, although there really edests some adVerse influence during theCPL start-up. Addihonally, the causes of the dry-out of the evaporator under low heat load are conducted in thepaper. The conclusions are verified by subsequent experiments. More details about the experiments are alsodescribed in the paper.
文摘The steady laminar pipe flow of a suspension with a gas volume fraction ∅≤0.5 and small or intermediate bubble deformations in long, and straight sections of a circular pipe is calculated. The calculations are based on the constitutive equation that was originally derived for dilute emulsions and further developed for concentrated suspensions containing bubbles. In contrast to the literature, an analytical procedure is used to determine the solution of a pipe flow more accurately. The results are presented and discussed with respect to the Reynolds number Re and capillary number Ca. If Ca 1, a bubble suspension has a parabolic velocity profile indicating a Newtonian rheology. If Ca ≈1, two regimes of flow are observed in agreement with the literature;that is, an inner plug flow where deformation rates are low and an outer flow where deformation rates are high. These results imply that, if Ca ∅?and that, if Ca ≥1, the opposite effect occurs;that is, the Reynolds number Re increases with increasing gas volume fraction.
