The influence of pre-deformation on aging precipitates of three near peak-aged Al–Cu–Li alloys,1460 alloy with a low Cu/Li ratio（1.46）,2050 alloy with a high Cu/Li ratio（4.51） and 2A96 alloy with a medium Cu/Li ...The influence of pre-deformation on aging precipitates of three near peak-aged Al–Cu–Li alloys,1460 alloy with a low Cu/Li ratio（1.46）,2050 alloy with a high Cu/Li ratio（4.51） and 2A96 alloy with a medium Cu/Li ratio（2.97）,was investigated.The strength of the aged alloys is enhanced by the pre-deformation.The effectiveness of pre-deformation on precipitates is dependent on the alloy＇s composition.With increasing the pre-deformation,the population density of T1（Al2Cu Li） precipitates increases in all three Al–Cu–Li alloys and their diameter decreases in 2050 and 2A96 alloys,and the greatest effectiveness is observed in 2A96 alloy.The pre-deformation also increases the population density of θ＇（Al2Cu）precipitates and decreases their diameter in 2050 and 2A96 Al–Li alloys,but the effectiveness is smaller compared to that on T1 precipitates.In 1460 alloy subjected to two-step aging at 130 ℃ for 20 h followed by 160 ℃ for 12 h,the main precipitates are δ＇（Al3Li）.At 2%–6% pre-deformation,GP-I zones form and pre-deformation displays little influence.Eight percentage pre-deformation promotes θ＇＇/θ＇ precipitation and increases their population density.展开更多
The effects of large cold deformation after solution treatment on the precipitation characteristic and deformation strength of 2024 and 7A04 Al alloys were investigated.The tensile property tests indicate that the age...The effects of large cold deformation after solution treatment on the precipitation characteristic and deformation strength of 2024 and 7A04 Al alloys were investigated.The tensile property tests indicate that the ageing response of the 2024 aluminum alloy is accelerated when treated by cold deformation after solution treatment,and the tensile strength is increased to about 140 MPa while the elongation still keeps above 8%.However,compared with the 2024 alloys,although the aging response of the cold deformed 7A04 aluminum alloy is accelerated,the tensile strength has not changed obviously and the elongation is even decreased drastically.The results of TEM observation show that the S’ phase inside the dislocation cells and at the boundaries of the dislocation cells of the 2024 aluminum alloy has a uniform distribution.But in 7A04 aluminum alloy the club-shaped η’ phase forms at the boundaries of dislocation cells even on dislocation lines,while there still exists small spheric G.P zone in the region with less dislocation.In addition the precipitates in 7A04 alloy with cold rolling present more obvious tendency of growth and coarsening than those without cold rolling.It is indicated that the coherent strain energy of the cylinder formed G.P zones with matrix in the 2024 alloy is smaller than that of the spherical G.P zone in 7A04 alloy,for which a different distribution of precipitates and different effect of strengthening are caused in artificial ageing after resolution treatment and large cold deformation.展开更多
The aging properties of Cu-0.35Cr-0.038Zr-0.055Ce alloy are studied. The results show that can obtain higher electrical conductivity and microhardness after solutioned at 920°Cfor Ih, and aged at 500°C. The ...The aging properties of Cu-0.35Cr-0.038Zr-0.055Ce alloy are studied. The results show that can obtain higher electrical conductivity and microhardness after solutioned at 920°Cfor Ih, and aged at 500°C. The process of precipitation of the secondary phase can be accelerated with cold deformation before aging, so properties of the alloy are improved. Upon aging at 500°C for 30 minutes after 60% cold deformation, the values of electrical conductivity and microhardness are 69.0%IACS and 152HV respectively, but they are only 66.2%IACS and 136HV upon directly aging after solution. With the addition of a trace of rare earth element Ce, the value of microhardness of Cu-0.35Cr-0.038Zr alloy increases 18-25HV, while the value of electrical conductivity drops a little.展开更多
The effect of pre-deformation followed by or together with artificial aging on the mechanical properties as strength and ductility of an AA6060 aluminium alloy was studied. AA6060 was initially cast, homogenized and e...The effect of pre-deformation followed by or together with artificial aging on the mechanical properties as strength and ductility of an AA6060 aluminium alloy was studied. AA6060 was initially cast, homogenized and extruded according to standard industrial practice. The extruded material was then subjected to a solution heat treatment and subsequently artificial aging after （sequential mode） and during （simultaneous mode） various combinations of deformation （0-10%） and heat treatments. The aging behaviour and mechanical properties were characterized in terms of Vickers hardness and tensile testing. It is found that precipitation kinetics and associated mechanical response, in terms of hardness and tensile properties are strongly affected by pre-deformations. In terms of aging behaviour, kinetics is accelerated and the peak strength generally increases. Comparing sequential mode and simultaneous mode, the latter seems to give overall better mechanical properties and after considerably shorter aging times. The results of the two modes of pre-deformation are compared and discussed in view of differences in processing conditions and microstructure characteristics.展开更多
This study focuses on the effects of different cold-drawing deformations and aging treatments of solid solution A286 superalloy.The grain configuration,texture,precipitates and tensile strength of A286 superalloy afte...This study focuses on the effects of different cold-drawing deformations and aging treatments of solid solution A286 superalloy.The grain configuration,texture,precipitates and tensile strength of A286 superalloy after different deformations and aging treatments were investigated by optical microscopy(OM),field emission scanning electron microscopy(FESEM),electron back-scattered diffraction(EBSD)and mechanical testing machine.The grain size and configuration of A286 alloy can hardly be changed during aging process.The initially equiaxial and twinned crystals are obvious when deformation is less than30%,while the grain boundaries become blurry and slip bands appear after 35% deformation or more.γ’ phase and Cr-rich carbide are the precipitates of A286 alloy.For each deformation,γ’ phase plays a major role during aging and its amount increases gradually when the aging temperature changes from 650 to 680℃,and a maximum tensile strength appears when following two-stage aging.With deformation increasing,the amounts of γ’ phase and Crrich carbide increase in varying degrees.Meanwhile,the<111>wire textures become more obvious,the tensile strength is enhanced and the kernel average misorientation(KAM)increases gradually;the higher KAM of crystal lattices diffuses from the grain boundary to the matrix gradually.展开更多
基金the National High Technology Research and Development Program of China(No.2013AA032401)Teacher’s Research Foundation of Central South University(No.2013JSJJ 001) for the financial supportNonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Centre
文摘The influence of pre-deformation on aging precipitates of three near peak-aged Al–Cu–Li alloys,1460 alloy with a low Cu/Li ratio（1.46）,2050 alloy with a high Cu/Li ratio（4.51） and 2A96 alloy with a medium Cu/Li ratio（2.97）,was investigated.The strength of the aged alloys is enhanced by the pre-deformation.The effectiveness of pre-deformation on precipitates is dependent on the alloy＇s composition.With increasing the pre-deformation,the population density of T1（Al2Cu Li） precipitates increases in all three Al–Cu–Li alloys and their diameter decreases in 2050 and 2A96 alloys,and the greatest effectiveness is observed in 2A96 alloy.The pre-deformation also increases the population density of θ＇（Al2Cu）precipitates and decreases their diameter in 2050 and 2A96 Al–Li alloys,but the effectiveness is smaller compared to that on T1 precipitates.In 1460 alloy subjected to two-step aging at 130 ℃ for 20 h followed by 160 ℃ for 12 h,the main precipitates are δ＇（Al3Li）.At 2%–6% pre-deformation,GP-I zones form and pre-deformation displays little influence.Eight percentage pre-deformation promotes θ＇＇/θ＇ precipitation and increases their population density.
基金Project(50571069) supported by NSFC and Project(05A061) education department of Hunan province,China
文摘The effects of large cold deformation after solution treatment on the precipitation characteristic and deformation strength of 2024 and 7A04 Al alloys were investigated.The tensile property tests indicate that the ageing response of the 2024 aluminum alloy is accelerated when treated by cold deformation after solution treatment,and the tensile strength is increased to about 140 MPa while the elongation still keeps above 8%.However,compared with the 2024 alloys,although the aging response of the cold deformed 7A04 aluminum alloy is accelerated,the tensile strength has not changed obviously and the elongation is even decreased drastically.The results of TEM observation show that the S’ phase inside the dislocation cells and at the boundaries of the dislocation cells of the 2024 aluminum alloy has a uniform distribution.But in 7A04 aluminum alloy the club-shaped η’ phase forms at the boundaries of dislocation cells even on dislocation lines,while there still exists small spheric G.P zone in the region with less dislocation.In addition the precipitates in 7A04 alloy with cold rolling present more obvious tendency of growth and coarsening than those without cold rolling.It is indicated that the coherent strain energy of the cylinder formed G.P zones with matrix in the 2024 alloy is smaller than that of the spherical G.P zone in 7A04 alloy,for which a different distribution of precipitates and different effect of strengthening are caused in artificial ageing after resolution treatment and large cold deformation.
基金supported by the National 863 Plan Items of China(No.2002AA331112)
文摘The aging properties of Cu-0.35Cr-0.038Zr-0.055Ce alloy are studied. The results show that can obtain higher electrical conductivity and microhardness after solutioned at 920°Cfor Ih, and aged at 500°C. The process of precipitation of the secondary phase can be accelerated with cold deformation before aging, so properties of the alloy are improved. Upon aging at 500°C for 30 minutes after 60% cold deformation, the values of electrical conductivity and microhardness are 69.0%IACS and 152HV respectively, but they are only 66.2%IACS and 136HV upon directly aging after solution. With the addition of a trace of rare earth element Ce, the value of microhardness of Cu-0.35Cr-0.038Zr alloy increases 18-25HV, while the value of electrical conductivity drops a little.
基金Project (176816/I40) supported by the Research Council of Norway
文摘The effect of pre-deformation followed by or together with artificial aging on the mechanical properties as strength and ductility of an AA6060 aluminium alloy was studied. AA6060 was initially cast, homogenized and extruded according to standard industrial practice. The extruded material was then subjected to a solution heat treatment and subsequently artificial aging after （sequential mode） and during （simultaneous mode） various combinations of deformation （0-10%） and heat treatments. The aging behaviour and mechanical properties were characterized in terms of Vickers hardness and tensile testing. It is found that precipitation kinetics and associated mechanical response, in terms of hardness and tensile properties are strongly affected by pre-deformations. In terms of aging behaviour, kinetics is accelerated and the peak strength generally increases. Comparing sequential mode and simultaneous mode, the latter seems to give overall better mechanical properties and after considerably shorter aging times. The results of the two modes of pre-deformation are compared and discussed in view of differences in processing conditions and microstructure characteristics.
基金financially supported by the National Natural Science Foundation of China(No. 11502285)
文摘This study focuses on the effects of different cold-drawing deformations and aging treatments of solid solution A286 superalloy.The grain configuration,texture,precipitates and tensile strength of A286 superalloy after different deformations and aging treatments were investigated by optical microscopy(OM),field emission scanning electron microscopy(FESEM),electron back-scattered diffraction(EBSD)and mechanical testing machine.The grain size and configuration of A286 alloy can hardly be changed during aging process.The initially equiaxial and twinned crystals are obvious when deformation is less than30%,while the grain boundaries become blurry and slip bands appear after 35% deformation or more.γ’ phase and Cr-rich carbide are the precipitates of A286 alloy.For each deformation,γ’ phase plays a major role during aging and its amount increases gradually when the aging temperature changes from 650 to 680℃,and a maximum tensile strength appears when following two-stage aging.With deformation increasing,the amounts of γ’ phase and Crrich carbide increase in varying degrees.Meanwhile,the<111>wire textures become more obvious,the tensile strength is enhanced and the kernel average misorientation(KAM)increases gradually;the higher KAM of crystal lattices diffuses from the grain boundary to the matrix gradually.
