The Al-9Zn-2.8Mg-2.5Cu-xZr-ySc alloys （x=0, 0.15%, 0.15%; y=0, 0.05%, 0.15%）, produced by low-frequent electromagnetic casting technology, were subjected to homogenization treatment, hot extrusion, solution and agin...The Al-9Zn-2.8Mg-2.5Cu-xZr-ySc alloys （x=0, 0.15%, 0.15%; y=0, 0.05%, 0.15%）, produced by low-frequent electromagnetic casting technology, were subjected to homogenization treatment, hot extrusion, solution and aging treatment. The effects of minor Sc and Zr addition on microstructure, recrystallization and properties of alloys were studied by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results show that Sc and Zr addition can refine grains of the as-cast alloy by precipitation of primary Al3（Sc,Zr） particles formed during solidification as heterogeneous nuclei. Secondary Al3（Sc,Zr） precipitates formed during homogenization treatment strongly pin the movement of dislocation and subgrain boundaries, which can effectively inhibit the alloys recrystallization. Compared with the alloy without Sc and Zr addition, the Al-Zn-Mg-Cu-Zr alloy with 0.05%Sc and 0.15%Zr shows the increase in tensile strength and yield strength by 172 MPa and 218 MPa, respectively. Strengthening comes from the contributions of precipitation, substructure and grain refining.展开更多
A comprehensive study on the microstructural evolution of a new type Al-Zn-Mg-Cu-Er-Zr alloy duringhomogenization was conducted by optical microscope,scanning electron microscope,transmission electron microscopy and X...A comprehensive study on the microstructural evolution of a new type Al-Zn-Mg-Cu-Er-Zr alloy duringhomogenization was conducted by optical microscope,scanning electron microscope,transmission electron microscopy and X-raydiffraction analysis.The results show that serious segregation exists in as-cast alloy,and the primary phases are T(AlZnMgCu),S(Al2CuMg)and Al8Cu4Er,which preferentially locate in the grain boundary regions.The soluble T(AlZnMgCu)and S(Al2CuMg)phases dissolve into the matrix gradually during single-stage homogenized at465°C with prolonging holding time,but the residualAl8Cu4Er phase cannot dissolve completely.Compared with the single-stage homogenization,both a finer particle size and a highervolume fraction of L12-structured Al3(Er,Zr)dispersoids can be obtained in the two-stage homogenization process.A suitablehomogenization scheme for the present alloy is(400°C,10h)+(465°C,24h),which is consistent with the results of homogenizationkinetic analysis.展开更多
The precipitation behavior, mechanical properties and corrosion resistance of a novel Al-Zn-Mg-Sc-Zr alloy aged at different time were studied by optical microscopy（OM）, scanning electron microscopy（SEM）, transmis...The precipitation behavior, mechanical properties and corrosion resistance of a novel Al-Zn-Mg-Sc-Zr alloy aged at different time were studied by optical microscopy（OM）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, tensile tests, potentiodynamic polarization and electrochemical impedance spectroscopy. The results revealed that with increasing aging time at 120 ℃, the hardness and tensile strength of the alloy increased rapidly at first and then slightly decreased. The resistance of exfoliation corrosion（EXCO） and intergranular corrosion（IGC） increased gradually with increasing aging time. The same trend of corrosion properties was demonstrated by electrochemical polarization curves and EIS test. The characteristics of grain boundary precipitates and precipitate free zone（PFZ） had a significant influence on the mechanical and corrosion behaviors of the studied alloy. On the basis of TEM observations, the size of grain boundary precipitates and the width of PFZ became larger, and the distributed spacing of grain boundary precipitates was enhanced with increasing aging time.展开更多
New samples returned by China Chang’e-5(CE-5)mission offer an opportunity for studying the lunar geologic longevity,space weathering,and regolith evolution.The age determination of the CE-5 samples was among the firs...New samples returned by China Chang’e-5(CE-5)mission offer an opportunity for studying the lunar geologic longevity,space weathering,and regolith evolution.The age determination of the CE-5 samples was among the first scientific questions to be answered.However,the precious samples,most in the micrometer size range,challenge many traditional analyses on large single crystals of zircon developed for massive bulk samples.Here,we developed a non-destructive rapid screening of individual zirconium-containing particle for isotope geochronology based on a Micro X-ray fluorescence analysis(μXRF).The selected particles were verified via scanning electron microscopy(SEM),3D X-ray microscopy(XRM),and focused ion beam scanning electron microscopy(FIB-SEM)techniques,which showed that zirconium-bearing minerals with several microns were precisely positioned and readily suitable for site-specific isotopic dating by second ion mass spectrometry(SIMS).Such protocol could be also appli-cable in non-destructively screening other types of particles for different scientific purposes.We there-fore proposed a correlative workflow for comprehensively studying the CE-5 lunar samples from single particles on nanometer to atomic scales.Linking various microscopic and spectromicroscopic instru-ments together,this workflow consists of six steps:(1)single-particle selection with non-destructive μXRF technique,(2)2D/3D morphological and structural characterization with a correlative submicron 3D XRM and nanoscale resolution FIB-SEM imaging methods,(3)SEM analysis of the surface morphology and chemistry of the selected particle,(4)a series of microscopic and microbeam analyses(e.g.,SEM,electron probe microanalysis,and SIMS)on the cross-section of the selected particle to obtain structural,mineralogical,chemical,and isotopic features from the micron to nanometer scale,(5)advanced 2D/3D characterization and site-specific sample preparation of thin foil/tip specimens on a microregion of inter-est in the selected particle with FIB-SEM techniqu展开更多
The influence of annealing cycles up to 650 °C on the specific conductivity and hardness（HV） of hot-rolled sheets of Al alloys containing up to 0.5% Zr（mass fraction） was studied.Using analytical calculations...The influence of annealing cycles up to 650 °C on the specific conductivity and hardness（HV） of hot-rolled sheets of Al alloys containing up to 0.5% Zr（mass fraction） was studied.Using analytical calculations of phase composition and experimental methods（scanning electron microscopy,transmission electron microscopy,electron microprobe analysis,etc）,it is demonstrated that the conductivity depends on the content of Zr in the Al solid solution which is the minimum after holding at 450 °C for 3 h.On the other hand,the hardness of the alloy is mainly caused by the amount of nanoparticles of the L12（Al3Zr） phase that defines the retention of strain hardening.It is shown that the best combination of electrical conductivity and hardness values can be reached within an acceptable holding time at the temperature about 450 °C.展开更多
Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is ...Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.展开更多
基金Project(0211002605132)supported by Institute of Multipurpose Utilization of Mineral Resources,Chinese Academy of Geological Sciences,ChinaProject(0211005303101)supported by the Fundamental Research Funds for the Central Universities,China+1 种基金Project(2010BB4074)supported by Natural Science Foundation Project of CQ CSTC,ChinaProject(2010ZD-02)supported by State Key Laboratory for Advanced Metals and Materials,China
文摘The Al-9Zn-2.8Mg-2.5Cu-xZr-ySc alloys （x=0, 0.15%, 0.15%; y=0, 0.05%, 0.15%）, produced by low-frequent electromagnetic casting technology, were subjected to homogenization treatment, hot extrusion, solution and aging treatment. The effects of minor Sc and Zr addition on microstructure, recrystallization and properties of alloys were studied by optical microscopy （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results show that Sc and Zr addition can refine grains of the as-cast alloy by precipitation of primary Al3（Sc,Zr） particles formed during solidification as heterogeneous nuclei. Secondary Al3（Sc,Zr） precipitates formed during homogenization treatment strongly pin the movement of dislocation and subgrain boundaries, which can effectively inhibit the alloys recrystallization. Compared with the alloy without Sc and Zr addition, the Al-Zn-Mg-Cu-Zr alloy with 0.05%Sc and 0.15%Zr shows the increase in tensile strength and yield strength by 172 MPa and 218 MPa, respectively. Strengthening comes from the contributions of precipitation, substructure and grain refining.
基金Project(2012CB619503) supported by the National Basic Research Program of ChinaProject(51201003) supported by the National Natural Science Foundation of ChinaProject(2142007) supported by Natural Science Foundation of Beijing,China
文摘A comprehensive study on the microstructural evolution of a new type Al-Zn-Mg-Cu-Er-Zr alloy duringhomogenization was conducted by optical microscope,scanning electron microscope,transmission electron microscopy and X-raydiffraction analysis.The results show that serious segregation exists in as-cast alloy,and the primary phases are T(AlZnMgCu),S(Al2CuMg)and Al8Cu4Er,which preferentially locate in the grain boundary regions.The soluble T(AlZnMgCu)and S(Al2CuMg)phases dissolve into the matrix gradually during single-stage homogenized at465°C with prolonging holding time,but the residualAl8Cu4Er phase cannot dissolve completely.Compared with the single-stage homogenization,both a finer particle size and a highervolume fraction of L12-structured Al3(Er,Zr)dispersoids can be obtained in the two-stage homogenization process.A suitablehomogenization scheme for the present alloy is(400°C,10h)+(465°C,24h),which is consistent with the results of homogenizationkinetic analysis.
基金Project(2012CB619503)supported by the National Basic Research Program of ChinaProjects(51475266,51005134)supported by the National Natural Science Foundation of China
文摘The precipitation behavior, mechanical properties and corrosion resistance of a novel Al-Zn-Mg-Sc-Zr alloy aged at different time were studied by optical microscopy（OM）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, tensile tests, potentiodynamic polarization and electrochemical impedance spectroscopy. The results revealed that with increasing aging time at 120 ℃, the hardness and tensile strength of the alloy increased rapidly at first and then slightly decreased. The resistance of exfoliation corrosion（EXCO） and intergranular corrosion（IGC） increased gradually with increasing aging time. The same trend of corrosion properties was demonstrated by electrochemical polarization curves and EIS test. The characteristics of grain boundary precipitates and precipitate free zone（PFZ） had a significant influence on the mechanical and corrosion behaviors of the studied alloy. On the basis of TEM observations, the size of grain boundary precipitates and the width of PFZ became larger, and the distributed spacing of grain boundary precipitates was enhanced with increasing aging time.
基金the National Key R&D Program of China(2018YFA0702600)the Key Research program of Chinese Academy of Sciences(ZDBS-SSW-JSC007-13)+1 种基金the institute of Geology and Geophysics,Chinese Academy of Sciences(IGGCAS-202101)the National Natural Science Foundation of China(grants no.41890843,41920104009)。
文摘New samples returned by China Chang’e-5(CE-5)mission offer an opportunity for studying the lunar geologic longevity,space weathering,and regolith evolution.The age determination of the CE-5 samples was among the first scientific questions to be answered.However,the precious samples,most in the micrometer size range,challenge many traditional analyses on large single crystals of zircon developed for massive bulk samples.Here,we developed a non-destructive rapid screening of individual zirconium-containing particle for isotope geochronology based on a Micro X-ray fluorescence analysis(μXRF).The selected particles were verified via scanning electron microscopy(SEM),3D X-ray microscopy(XRM),and focused ion beam scanning electron microscopy(FIB-SEM)techniques,which showed that zirconium-bearing minerals with several microns were precisely positioned and readily suitable for site-specific isotopic dating by second ion mass spectrometry(SIMS).Such protocol could be also appli-cable in non-destructively screening other types of particles for different scientific purposes.We there-fore proposed a correlative workflow for comprehensively studying the CE-5 lunar samples from single particles on nanometer to atomic scales.Linking various microscopic and spectromicroscopic instru-ments together,this workflow consists of six steps:(1)single-particle selection with non-destructive μXRF technique,(2)2D/3D morphological and structural characterization with a correlative submicron 3D XRM and nanoscale resolution FIB-SEM imaging methods,(3)SEM analysis of the surface morphology and chemistry of the selected particle,(4)a series of microscopic and microbeam analyses(e.g.,SEM,electron probe microanalysis,and SIMS)on the cross-section of the selected particle to obtain structural,mineralogical,chemical,and isotopic features from the micron to nanometer scale,(5)advanced 2D/3D characterization and site-specific sample preparation of thin foil/tip specimens on a microregion of inter-est in the selected particle with FIB-SEM techniqu
基金Project(RMEF157814X0004)supported by the Ministry of Education and Science of the Russian Federation
文摘The influence of annealing cycles up to 650 °C on the specific conductivity and hardness（HV） of hot-rolled sheets of Al alloys containing up to 0.5% Zr（mass fraction） was studied.Using analytical calculations of phase composition and experimental methods（scanning electron microscopy,transmission electron microscopy,electron microprobe analysis,etc）,it is demonstrated that the conductivity depends on the content of Zr in the Al solid solution which is the minimum after holding at 450 °C for 3 h.On the other hand,the hardness of the alloy is mainly caused by the amount of nanoparticles of the L12（Al3Zr） phase that defines the retention of strain hardening.It is shown that the best combination of electrical conductivity and hardness values can be reached within an acceptable holding time at the temperature about 450 °C.
文摘Microstructure evolution and texture development and their effects on mechanical properties of a Mg-Gd-Y-Zr alloy during equal channel angular pressing（ECAP） were investigated.It is found that the microstructure is still inhomogeneous after four passes,and two zones,namely the fine grain zone（FGZ） and the coarse grain zone（CGZ） are formed.The grain refinement occurs mainly by particle-stimulated nucleation（PSN） mechanism,which led to a more random texture after four passes of ECAP.In the ECAP-processed alloy,the strength did not increase while the ductility was enhanced dramatically compared with the as-received condition.The change of ductility of this alloy was discussed in terms of texture and second phase particles.
