期刊文献+
共找到17篇文章
< 1 >
每页显示 20 50 100
红色蓄光材料Y_2O_2S∶Eu^(3+)的硫熔法制备及其发光性能 被引量:7
1
作者 王治龙 王育华 《功能材料》 EI CAS CSCD 北大核心 2005年第9期1328-1330,共3页
用硫熔法制备了系列红色蓄光材料Y2O2S∶Eu3x+(0.01≤x≤0.10)的多晶粉末样品并系统研究了其发光特性。XRD结果表明,晶胞参数c随着Eu3+含量的逐渐增大而增大,而晶胞参数a没有明显的线性变化关系,这与Y2O2S∶Eu3+的晶体结构有关。Y2O2S∶... 用硫熔法制备了系列红色蓄光材料Y2O2S∶Eu3x+(0.01≤x≤0.10)的多晶粉末样品并系统研究了其发光特性。XRD结果表明,晶胞参数c随着Eu3+含量的逐渐增大而增大,而晶胞参数a没有明显的线性变化关系,这与Y2O2S∶Eu3+的晶体结构有关。Y2O2S∶Eux3+(0.01≤x≤0.10)的激发光谱相似,在626nm发射光监控下最大激发波长约在330nm附近。在330nm激发下,随着Eu3+含量逐渐增大,发射光谱最强发射峰位置从540nm右移至626nm,观察到红色特征发射峰626nm的强度逐渐增大,在Eu3+含量为0.09时,其强度达到最大。在最佳合成条件及最佳Eu3+含量下,正在进行掺杂Mg2+和Ti4+及其发光特性的研究。 展开更多
关键词 y2o2S ^:eu^3+ 硫熔法 蓄光材料
下载PDF
Y_2O_2S∶Eu^(3+),Mg^(2+),Ti^(4+)长余辉材料制备中烧结条件和助熔剂的影响 被引量:5
2
作者 魏雅姝 张金朝 宋鹂 《应用化学》 CAS CSCD 北大核心 2005年第12期1342-1346,共5页
采用高温固相法合成了Y2O2S∶Eu3+,Mg2+,Ti4+红色长余辉材料。通过X射线衍射分析和扫描电镜测试技术研究了样品的晶体结构和颗粒的大小、形貌,分析了有助于晶体颗粒生长的烧结温度、气氛以及助熔剂对它的影响,还对荧光体的发光光谱、相... 采用高温固相法合成了Y2O2S∶Eu3+,Mg2+,Ti4+红色长余辉材料。通过X射线衍射分析和扫描电镜测试技术研究了样品的晶体结构和颗粒的大小、形貌,分析了有助于晶体颗粒生长的烧结温度、气氛以及助熔剂对它的影响,还对荧光体的发光光谱、相对亮度、余辉性质进行了研究。结果表明,制备得到的Y2O2S∶Eu3+,Mg2+,Ti4+红色长余辉材料体系相态纯净,有较完整和均匀的晶形,完整的晶体结构有利于提高荧光体的发光性质。制备中合适的烧结温度为1 150℃,要选择弱还原气氛。加入L i3PO4可以使晶体颗粒的晶型完整,粒径增大,并且粒度分布较窄。 展开更多
关键词 y2o2S ^eu^3+ ^MG^2+ ^Ti^4+ 烧结条件 助熔剂 发光性质
下载PDF
Characterization of Y_2O_2S∶Eu ^(3+), Mg^(2+), Ti^(4+) Long-Lasting Phosphor Synthesized by Flux Method 被引量:8
3
作者 王育华 王治龙 《Journal of Rare Earths》 SCIE EI CAS CSCD 2006年第1期25-28,共4页
Long-lasting phosphor Y2O2S : Eu^3+ , Mg^2+ , Ti^4+ was synthesized by a flux method and their luminescence properties were investigated. The result indicates that the unit cell parameter c is linearly increased w... Long-lasting phosphor Y2O2S : Eu^3+ , Mg^2+ , Ti^4+ was synthesized by a flux method and their luminescence properties were investigated. The result indicates that the unit cell parameter c is linearly increased with the increase of Eu2O3 content in Y2O2S: Eu^3+ (0.01 ≤ x ≤0.10). On the other hand, the change of unit cell parameter a is not linear dependence. In the Y2O2S: Eu^3 + crystal structure, Eu^3+ ions only replaced Y^3 + ions' places in which it posited center position of c axis. With the increase of Eu2O3 content, the position of the strongest emission peak changed from 540 nm (5D1→^ 7F2 transition) to 626 nm (^5Do→^7TF2 transition), and the maximum intensity was obtained when x = 0.09 in Y2O2S: Eu^3+ (0.01 ≤x ≤0.10). This is due to the environment of trivalent europium in the crystal structure of Y2O2S. Doping with Mg^2+ or Ti^4+. ions alone cannot get the good long-lasting afterglow effect, whereas co-doping with Mg^2 + and Ti^4 + ions and excited with 365 nm ultraviolet light, a strong thermoluminesence peak appeared, red and orange long-lasting phosphorescence (LLP) was also observed and the phosphorescence lasted nearly 3 h in the light perception of the dark-adapted human eye (0.32 mcd·m^-2). Thus the LLP mechanism was analyzed. 展开更多
关键词 y2o2S: ^eu^3 ^Mg^2 ^Ti^4 flux method long-lasting phosphorescence material rare earths
下载PDF
共沉淀法制备Y_2O_2S∶Eu^(3+),Mg^(2+),Ti^(4+)红色长余辉材料 被引量:4
4
作者 杨志平 李兴民 +2 位作者 杨勇 李旭 李盼来 《发光学报》 EI CAS CSCD 北大核心 2006年第2期187-190,共4页
用共沉淀法制备了Y2O2S∶Eu3+,Mg2+,Ti4+红色长余辉材料。测量了材料的电子显微形貌、晶体结构和发射光谱。通过与固相法制备的Y2O2S∶Eu3+,Mg2+,Ti4+长余辉材料比较,发现两种方法都可以制备粒度基本相同的纯相Y2O2S基质晶体,但共沉淀... 用共沉淀法制备了Y2O2S∶Eu3+,Mg2+,Ti4+红色长余辉材料。测量了材料的电子显微形貌、晶体结构和发射光谱。通过与固相法制备的Y2O2S∶Eu3+,Mg2+,Ti4+长余辉材料比较,发现两种方法都可以制备粒度基本相同的纯相Y2O2S基质晶体,但共沉淀法样品的颗粒结构更松散。研究了Eu3+浓度对两种方法制备样品的谱线发射强度的影响,通过比较共沉淀法和高温固相法制备的样品中Eu3+的5D1→7F3较高能级跃迁的587.6 nm谱线强度随Eu3+浓度的变化,发现共沉淀法更有利于Eu3+均匀进入Y2O2S基质晶格而形成有效的发光中心。 展开更多
关键词 共沉淀 发射光谱 ^y2o2S:eu^3+ ^MG^2+ ^Ti^4+
下载PDF
纳米Y_2O_2S:Eu^(3+)红色荧光粉的间接法制备及发光性质 被引量:4
5
作者 耿阳 陈红卫 《应用化工》 CAS CSCD 2007年第3期260-262,共3页
用间接法制备纳米级红色荧光粉Y2O2S:Eu3+(物质的量之比为Eu3+/Y3+=0.02)。XRD测试表明,制得纳米级的Y2O2S:Eu3+为单一纯相。透射电子显微镜(TEM)扫描结果显示纳米材料的平均颗粒尺寸为30 nm,与Debye-Scherre公式计算的结果基本一致。... 用间接法制备纳米级红色荧光粉Y2O2S:Eu3+(物质的量之比为Eu3+/Y3+=0.02)。XRD测试表明,制得纳米级的Y2O2S:Eu3+为单一纯相。透射电子显微镜(TEM)扫描结果显示纳米材料的平均颗粒尺寸为30 nm,与Debye-Scherre公式计算的结果基本一致。荧光光谱中,激发光谱分为3个区域,200-280 nm的区域为Y2O2S基质的激子激发带,峰值为262 nm;280-380 nm的区域属于Eu3+→O2-(S2-)的电荷迁移带,峰值为319 nm;而位于399 nm和472 nm的线状光谱则属于Eu3+的4 f组态内部电子之间的跃迁。 展开更多
关键词 y2o2S ^eu^3+ 间接法 光谱分析
下载PDF
Vacuum Ultraviolet Excited Photoluminescence Properties of Y_2O_2S:Eu^(3+),Bi^(3+) Phosphor 被引量:4
6
作者 WANG Zhi-long WANG Yu-hua ZHANG Jia-chi 《Chemical Research in Chinese Universities》 SCIE CAS CSCD 2008年第6期679-682,共4页
As an Hg-free lamp using phosphor, the Bi^3+ and EH^3+ co-doped Y2O2S phosphors were prepared and their luminescence properties under vacuum ultraviolet(VUV) excitation were investigated. The VUV photoluminescent ... As an Hg-free lamp using phosphor, the Bi^3+ and EH^3+ co-doped Y2O2S phosphors were prepared and their luminescence properties under vacuum ultraviolet(VUV) excitation were investigated. The VUV photoluminescent intensity of Y2O2S:Eu^3+ was weak, however, considerably stronger red emission at 626 nm with good color purity was observed in Y2O2S:Eu^3+,Bi^3+ systems. Investigation on the photoluminescence reveals that the strong VUV luminescence of Y2O2S:Eu^3+,Bi^3+ at 147 nm is mainly because the Bi^3+ acts as a medium and effectively performs the energy transfer process: Y^3+-O^2-→Bi^3+→Eu^3+, while the intense emission band at 172 nm is attributed to the absorption of the characteristic ^1So-^1P1 transition of Bi^3+ and the direct energy transfer from Bi^3+ to Eu^3+. The Y2O2S:Eu^3+,Bi^3+ shows excellent VUV optical properties compared with the commercial (Y,Gd)BO3:Eu^3+. Thus, the Y2O2S:Eu^3+,Bi^3+ can be a potential red VUV-excited candidate applied in Hg-free lamps for backlight of liquid crystal display. 展开更多
关键词 ^y2o2S:eu^3+ ^Bi^3 Vacuum ultraviolet(VUV) PHoSPHoR
下载PDF
Ti^(4+)的掺入对Y_2O_2S:Eu^(3+),Mg^(2+),Ti^(4+)陷阱分布和余辉性能的影响 被引量:2
7
作者 杨志平 冯建伟 +2 位作者 李旭 刘玉峰 李兴民 《河北大学学报(自然科学版)》 CAS 北大核心 2005年第3期262-266,共5页
用高温固相法制备了不同Ti4+掺杂量的红色长余辉材料Y2O2S:Eu3+,Mg2+,Ti4+,其X射线衍射分析、发射光谱和激发光谱均不受Ti4+掺杂量改变的影响.测量了Ti4+掺杂量不同的样品的热释光谱,随着Ti4+掺杂量的增加,热释光的峰值强度先增强后减弱... 用高温固相法制备了不同Ti4+掺杂量的红色长余辉材料Y2O2S:Eu3+,Mg2+,Ti4+,其X射线衍射分析、发射光谱和激发光谱均不受Ti4+掺杂量改变的影响.测量了Ti4+掺杂量不同的样品的热释光谱,随着Ti4+掺杂量的增加,热释光的峰值强度先增强后减弱,有了很大的变化;用PeakFit软件以一般阶动力学模型对Ti与Y2O2S的物质的量比分别为0.5%,2.5%和8.0%的样品进行了热释光曲线拟合,得出了它的单峰曲线并计算了与其对应的陷阱参数.陷阱分布表明:当Ti掺杂量为2.5%时,有利于合适深度陷阱的大量形成,从而使材料的发光和余辉性能得到了很大的提高. 展开更多
关键词 红色长余辉 ^y2o2S:eu^3+ ^Mg^2+ ^Ti^4+ 热释光 陷阱
下载PDF
Y2O2S:Eu^3+红色荧光粉的SnO2:Sb包覆研究
8
作者 姜正伟 李怀祥 +1 位作者 夏荣花 于磊 《纳米科技》 2008年第1期6-9,共4页
采用硫融法合成了Y2O2S:Eu^3+红色荧光粉。用溶胶-凝胶法在其表面包覆了一层SnO2:Sb透明导电薄膜。通过x射线衍射(XRD)、透射电镜(TEM)、荧光光谱(PL)和电阻测量等检测手段分别分析了包覆处理对Y2O2S:Eu^3+的晶体结构、表面... 采用硫融法合成了Y2O2S:Eu^3+红色荧光粉。用溶胶-凝胶法在其表面包覆了一层SnO2:Sb透明导电薄膜。通过x射线衍射(XRD)、透射电镜(TEM)、荧光光谱(PL)和电阻测量等检测手段分别分析了包覆处理对Y2O2S:Eu^3+的晶体结构、表面形貌、荧光性质以及荧光粉导电性的影响。结果表明:通过该方法成功地在Y2O2S:Eu^3+表面包覆了一层连续的SnO2:Sb薄膜;当包覆量nSoO2/nY2O2S=6%时,所得到的荧光粉同时具有较高的荧光强度和导电性;当掺杂量DSb/nSn=10%,退火温度为500℃(氧气流中退火1h)时,可以得到导电性较好的荧光粉。 展开更多
关键词 ^y2o2S:eu^3+ 溶胶-凝胶法 包覆 导电性
下载PDF
原材料Y_2O_3的结晶性对Y_2O_2S∶Eu^(3+)发光特性的影响 被引量:4
9
作者 袁剑辉 张振华 +1 位作者 王晓君 程玉民 《光学学报》 EI CAS CSCD 北大核心 2005年第9期1243-1248,共6页
为进一步提高Y2O2S∶Eu3+的发光性能,采用改善主要原材料Y2O3结晶性的方法,使Y2O2S∶Eu3+红色荧光粉在20 kV和25 kV下发光强度分别增强5%和10%,且不影响色度、粒度、粉体分散性等主要考核指标。提高了粉体的耐电压特性(发射强度与激发... 为进一步提高Y2O2S∶Eu3+的发光性能,采用改善主要原材料Y2O3结晶性的方法,使Y2O2S∶Eu3+红色荧光粉在20 kV和25 kV下发光强度分别增强5%和10%,且不影响色度、粒度、粉体分散性等主要考核指标。提高了粉体的耐电压特性(发射强度与激发电压间的关系特性)。讨论和分析了发射强度增强、电压特性改善的原因:主要原材料Y2O3的结晶性的改善,使得合成的Y2O2S∶Eu3+具有更好的晶体质量,Eu3+离子晶场环境得到进一步改善,从而减弱了无辐射过程及因晶格畸变所造成的能量损失,发光效率得到增强,电压特性得到改善。实验表明,获取高质量多晶Y2O3的最佳分解温度为1400℃左右。 展开更多
关键词 光学材料 ^y2o2S:eu^3+荧光粉 y2o3结晶性 发光强度 耐压性
原文传递
Optical performance study of Sr_2ZnSi_2O_7:Eu^(2+),Dy^(3+), SrAl_2O_4:Eu^(2+),Dy^(3+) and Y_2O_2S:Eu^(3+),Mg^(2+),Ti^(4+) ternary luminous fiber 被引量:8
10
作者 晋阳 龙啸云 +1 位作者 朱亚楠 葛明桥 《Journal of Rare Earths》 SCIE EI CAS CSCD 2016年第12期1206-1212,共7页
In this study, down-conversion fluorescent powder of Sr2ZnSi2O7:Eu-(2+),Dy-(3+), SrAl2O4:Eu-(2+),Dy-(3+) and Y2O2S:Eu-(3+),Mg-(2+),Ti-(4+), which were the common three primary colors materials ... In this study, down-conversion fluorescent powder of Sr2ZnSi2O7:Eu-(2+),Dy-(3+), SrAl2O4:Eu-(2+),Dy-(3+) and Y2O2S:Eu-(3+),Mg-(2+),Ti-(4+), which were the common three primary colors materials with long afterglow, were synthesized by high temperature solid state method. The blends of rare earth(RE) luminescent materials have been of interest to reinvest the luminescent characteristics of polyethylene terephtahalate(PET) luminous fiber. The scanning electron microscopy(SEM) and an inversion fluorescence microscope were used to characterize the surface morphology and the dispersion of inclusion. Through analysis of microcosmic morphology, three typical dispersions of luminescent particles were summarized. The X-ray diffraction indicated that the phase structure of fiber samples and crystal structure of luminescence materials kept complete after prilling and spinning. From the fluorescence spectra and CIE 1931 coordinates, it could be found that different combinations of luminous fibers were desired to obtain divers colors emission luminous fiber. And the fiber samples were a light sensation which could induct different excitation wavelengths and convert it down to different colors. The afterglow decay curve and its differential curve were summarized indicating the three decay stages. The decay curve and decay rate curve showed that the contents of Sr2ZnSi2O7:Eu-(2+),Dy-(3+), SrAl2O4:Eu-(2+),Dy-(3+) and Y2O2S:Eu-(3+),Mg-(2+),Ti-(4+) had obvious influence on the afterglow of fiber samples. 展开更多
关键词 luminous fiber ^Sr_2ZnSi_2o_7:eu^2 ^Dy^3 ^SrAl_2o_4:eu^2 ^Dy^3 ^y_2o_2S:eu^3+ ^Mg^2 ^Ti^4+ down-conversion light sensation rare earths
原文传递
高亮度长余辉蓄光型红色荧光粉的研制
11
作者 田玉伟 《光源与照明》 2011年第3期42-44,共3页
简单介绍了目前国内外长余辉荧光粉的现状,简述高亮度、长余辉的红色荧光粉原材料的预处理方法;介绍该荧光粉的最佳合成工艺试验及制备工艺;给出该粉的蓄光和发光特性。
关键词 ^y_2o_2S:eu^3+ ^CA^2+ ^Ti^4+ 高亮度 长余辉 红色荧光粉
下载PDF
Effects of Doping Trace Sm^(3+) and Gd^(3+) on Luminescent Character of Y_2O_2S∶Eu^(3+)
12
作者 Yuan Jianhui Yuan Honghui +2 位作者 Zhang Zhenhua Cheng Yumin Wang Xiaojun 《Journal of Rare Earths》 SCIE EI CAS CSCD 2005年第4期410-410,共1页
After trace Sm^3+ ions and Gd^3+ ions doping, the emission intensity of red phosphors Y2O2S: Eu^3 + was enhanced and the voltage character (relation between emission intensity and excitation voltage) was improve... After trace Sm^3+ ions and Gd^3+ ions doping, the emission intensity of red phosphors Y2O2S: Eu^3 + was enhanced and the voltage character (relation between emission intensity and excitation voltage) was improved while the other properties of physics and chemistry were not changed. The origins of enhancement and improvement are discussed. Probably the distortion and the defect of crystals are decreased by the substitution of Gd^3+ for Y^3+ instead of Eu^3+ for Y^3+ , and thus the Eu^3+ crystal field is improved, and radiationless process and energy loss resulted from crystal defect are weakened, which leads to increased luminescence intensity and voltage character improvement. The overlapping fluorescent spectra of Y2O2S: Sm^3+ emission and Y2O2S:Eu^3+ excitation as well as Eu^3 + excitation spectra transitions spectra lead to energy transfer from Sm^3 + sensitization of Sm^3+ ions fectively. containing Sm^3+ excitation the possibility of resonance ions to Eu^3+ ions, and the to Eu^3+ ions is achieved effectively. 展开更多
关键词 luminescence ^Sm^3 ^Gd^3 eodoped y2o2S ^eu^3 enhancement of emission intensity improvement of voltage resistance character rare earths
下载PDF
Y_2O_2S:Eu^(3+),Mg^(2+),Ti^(4+)红色材料的制备和长余辉性能 被引量:14
13
作者 杨志平 郭智 +1 位作者 王文杰 朱胜超 《发光学报》 EI CAS CSCD 北大核心 2004年第2期183-187,共5页
用高温固相法制备了Y_2O_2S:Eu^(3+),Mg^(2+),Ti^(4+)红色长余辉材料,余辉时间达到1h以上,X射线衍射测量表明材料的晶体结构为Y_2O_2S。发射光谱对应了Eu^(3+)离子~5D_J(J=0,1,2,3)→~7F_J(J=0,1,2,3,4)的特征发射;激发光谱主峰位于345 ... 用高温固相法制备了Y_2O_2S:Eu^(3+),Mg^(2+),Ti^(4+)红色长余辉材料,余辉时间达到1h以上,X射线衍射测量表明材料的晶体结构为Y_2O_2S。发射光谱对应了Eu^(3+)离子~5D_J(J=0,1,2,3)→~7F_J(J=0,1,2,3,4)的特征发射;激发光谱主峰位于345 um,另外在260,396,468,540 um等处也存在激发峰。对比测量了Y_2O_2S:Eu^(3+),Mg^(2+),Ti_(4+)和Y_2O_2S:Eu^(3+)的热释发光曲线,Y_2O_2S:Eu^(3+)的热释发光曲线可以拟合成3个热释发光峰的叠加:237,226,301K;而Y_2O_2S:Eu^(3+),Mg^(2+),Ti^(4+)的热释发光曲线可以拟合成5个热释发光峰的叠加:149,215,262,287,334 K,并计算了相应的陷阱能级。Ti^(4+)是引起较深陷阱能级的主要原因,Mg^(2+)起电荷补偿的作用。 展开更多
关键词 高温固相法 长余辉 激发光谱 发射光谱 热释发光 稀土发光材料 发光效率 晶体结构 铒离子 镁离子
下载PDF
痕量双掺Sm^(3+)和Gd^(3+)对Y_2O_2S∶Eu^(3+)发光特性的影响 被引量:5
14
作者 袁剑辉 袁红辉 +2 位作者 张振华 程玉民 王晓君 《中国稀土学报》 CAS CSCD 北大核心 2005年第4期421-424,共4页
通过对Y2O2S∶Eu3+红色荧光粉痕量引入Sm3+和Gd3+的研究,发现可有效地增强发光强度,明显改善其电压特性(发射强度与激发电压间的关系特性),且不影响材料的其他物理化学性能。讨论和分析了发射强度增强、电压特性改善的原因:Gd3+对Y3+的... 通过对Y2O2S∶Eu3+红色荧光粉痕量引入Sm3+和Gd3+的研究,发现可有效地增强发光强度,明显改善其电压特性(发射强度与激发电压间的关系特性),且不影响材料的其他物理化学性能。讨论和分析了发射强度增强、电压特性改善的原因:Gd3+对Y3+的置换,减少了因Eu3+对Y3+置换所引起的晶格的畸变、缺陷,使Eu3+离子晶场环境得到改善,从而减弱了无辐射过程及因晶格畸变所造成的能量损失;Sm3+的发射与Eu3+的吸收(激发)的部分重叠,且Eu3+激发光谱中包含有Sm3+激发跃迁谱线,导致了Sm3+→Eu3+共振能量传递可能性,有效地实现Sm3+对Eu3+的敏化效应。 展开更多
关键词 发光学 Sm3+∶Gd3+共掺 y2o2S∶eu3+ 发光增强 耐压性提高 稀土
下载PDF
红色Y_2O_2S:Eu^(3+)磷光材料的沉淀法制备和发光性能研究 被引量:5
15
作者 杨志平 刘冲 +3 位作者 郭智 冯建伟 杨勇 李兴民 《河北大学学报(自然科学版)》 CAS 2004年第6期585-588,593,共5页
用沉淀法制备了Eu3+掺杂的Y2O2S磷光材料,测量并研究了掺杂不同物质的量的Eu3+离子的Y2O2S磷光材料的发射谱和激发谱.发射光谱对应了Eu3+离子5DJ(J=0,1,2,3)-7FJ(J=0,1,2,3,4)的特征发射,激发光谱主峰对应260,345,468,540nm等,余辉时间... 用沉淀法制备了Eu3+掺杂的Y2O2S磷光材料,测量并研究了掺杂不同物质的量的Eu3+离子的Y2O2S磷光材料的发射谱和激发谱.发射光谱对应了Eu3+离子5DJ(J=0,1,2,3)-7FJ(J=0,1,2,3,4)的特征发射,激发光谱主峰对应260,345,468,540nm等,余辉时间(到人眼的最小亮度分辨率0.32mcd/m2)可达1h以上. 展开更多
关键词 长余辉 y2o2S ^eu^3+ 沉淀法
下载PDF
Magnetic and luminescent properties of bifunctional composite Fe_(3)O_(4)@Y_(2)O_(2)S:Eu^(3+)
16
作者 Zhiqi Liang Zhili Zhang +2 位作者 Liu Li Wen Xu Decai Li 《Journal of Rare Earths》 SCIE EI CAS CSCD 2024年第8期1568-1576,I0006,共10页
As a kind of non-destructive testing method,magnetic particle inspection is widely used in the fields of aviation and high-speed rail.The properties of magnetic fluorescent bifunctional composites,such as fluorescence... As a kind of non-destructive testing method,magnetic particle inspection is widely used in the fields of aviation and high-speed rail.The properties of magnetic fluorescent bifunctional composites,such as fluorescence intensity and magnetic properties,have increasing demands in magnetic particle inspection.Rare earth compounds offer potential as novel materials for fluorescent magnetic bifunctional composites due to their excellent optical properties and extremely narrow emission spectra.In this work,the rare earth fluorescent material Y_(2)O_(2)S:Eu^(3+) was synthesized by solid-state reaction method.Fe_(3)O_(4)nanoparticles prepared by hydrothermal method were uniformly coated on the Y_(2)O_(2)S:Eu^(3+) particles through physical adsorption of surfactants.The obtained Fe_(3)O_(4)@Y_(2)O_(2)S:Eu^(3+) exhibits dark red color under the ultraviolet light.In additio n,X-ray diffractio n,morphology,photoluminescence and hyste resis loop of Fe_(3)O_(4)@Y_(2)O_(2)S:Cu^(3+) were investigated.The luminescence mechanism of Y_(2)O_(2)S:Eu^(3+) is described in detail Fe_(3)O_(4)@Y_(2)O_(2)S:Cu^(3+) displays good paramagnetism and has a good controllability under a magnetic field.The magnetic particle inspection of Fe_(3)O_(4)@Y_(2)O_(2)S:Eu^(3+) was performed using a 4-pole electromagnet and a test piece shim.The magnetic fluorescent bifunctional composite presented in this work can be applied for non-destructive testing. 展开更多
关键词 Bifunctional material Fe_(3)o_(4) ^y_(2)o_(2)S:eu^(3+) Luminescence Solid-state reaction Rare earths
原文传递
Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒的合成及发光性能
17
作者 王玉香 钟盛文 +1 位作者 文小强 张骞 《稀有金属材料与工程》 SCIE EI CAS CSCD 北大核心 2021年第4期1204-1209,共6页
以Na_(2)SO_(4)和K_(2)SO_(4)为熔盐,采用熔盐法合成了一维Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒。应用X射线衍射、扫描电子显微镜和光谱仪等方法对合成产物的晶体结构、形貌和发光性能进行表征。考察了烧结温度、Eu^(3+)掺杂浓度对合成产... 以Na_(2)SO_(4)和K_(2)SO_(4)为熔盐,采用熔盐法合成了一维Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒。应用X射线衍射、扫描电子显微镜和光谱仪等方法对合成产物的晶体结构、形貌和发光性能进行表征。考察了烧结温度、Eu^(3+)掺杂浓度对合成产物的晶体结构、形貌和发光性能的影响。结果表明,原料混合物在1100℃空气中煅烧2 h可合成纯相、表面光滑的Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒,Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒的长度大于10μm,宽度为500~800 nm。在270 nm紫外光的激发下,Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒呈红光发射,最强发射峰位于616 nm处,归属于Eu^(3+)的^(5)D_(0)→^(7)F_(2)跃迁,Y_(2)O_(2)SO_(4):Eu^(3+)亚微米棒Eu^(3+)的最佳掺杂浓度为10mol%。 展开更多
关键词 熔盐法 ^y_(2)o_(2)So_(4):eu^(3+)亚微米棒 ^eu^(3+)掺杂
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部