The purpose is to reestablish the balance laws of momentum, angular momentum and energy and to derive the corresponding local and nonlocal balance equations for micromorphic continuum mechanics and couple stress theor...The purpose is to reestablish the balance laws of momentum, angular momentum and energy and to derive the corresponding local and nonlocal balance equations for micromorphic continuum mechanics and couple stress theory. The desired results for micromorphic continuum mechanics and couple stress theory are naturally obtained via direct transitions and reductions from the coupled conservation law of energy for micropolar continuum theory, respectively. The basic balance laws and equations for micromorphic continuum mechanics and couple stress theory are constituted by combining these results derived here and the traditional conservation laws and equations of mass and microinertia and the entropy inequality. The incomplete degrees of the former related continuum theories are clarified. Finally, some special cases are conveniently derived.展开更多
The linear and nonlinear torsional free vibration analyses of functionMly graded micro/nuno-tubes （FGMTs） are analytically investigated based on the couple stress theory. The employed non-classical continuum theory ...The linear and nonlinear torsional free vibration analyses of functionMly graded micro/nuno-tubes （FGMTs） are analytically investigated based on the couple stress theory. The employed non-classical continuum theory contains one material length scale parameter, which can capture the small scale effect. The FGMT model accounts for the through-radius power-law variation of a two-constituent material. Hamilton＇s principle is used to develop the non-classical nonlinear governing equation. To study the effect of the boundary conditions, two types of end conditions, i.e., fixed-fixed and fixed-free, are considered. The derived boundary value governing equation is of the fourthorder, and is solved by the homotopy analysis method （HAM）. This method is based on the Taylor series with an embedded parameter and is capable of providing very good approximations by means of only a few terms, if the initial guess and the auxiliary linear operator are properly selected. The analytical expressions are developed for the linear and nonlinear natural frequencies, which can be conveniently used to investigate the effects of the dimensionless length scale parameter, the material gradient index, and the vibration amplitude on the natural frequencies of FGMTs.展开更多
Among many theories and categories in microstructures,rotation-displacement used as "independent" or "dependent" variables,is a noticeable topic. In FEM,it is called C0 and C1 theory. The convergen...Among many theories and categories in microstructures,rotation-displacement used as "independent" or "dependent" variables,is a noticeable topic. In FEM,it is called C0 and C1 theory. The convergence criteria of finite elements for microstructures are less mature than those for the conventional thin plate bending problem. In this paper,the patch test functions for assessing convergence of the C0 and C1 finite elements in microstructures is established based on the enhanced patch test theory. The author has further explored the C0 and C1 finite element theories and investigated the difference and correlation between their finite element formulations. Newly proposed finite element theories for microstructures are as follows:(1) the displacement-rotation dependent C1 element that requires the element function satisfying both C0 and C1 continuity;(2) the displacement-rotation independent C0 element which requires new convergence criteria,such as non-zero constant shear stress patch test and zero constant shear stress patch test for approximating C1 element.展开更多
The enhanced patch test proposed by Chen W J(2006) can be used to assess the convergence of the problem with non-homogeneous differential equations.Based on this theory,we establish the patch test function for axisymm...The enhanced patch test proposed by Chen W J(2006) can be used to assess the convergence of the problem with non-homogeneous differential equations.Based on this theory,we establish the patch test function for axisymmetric elements of conventional and couple stress theories,and reach an important conclusion that the patch test function for axisymmetric elements cannot contain non-zero constant shear.展开更多
A non-classical Kirchhoff plate model is developed for the dynamic analysis of microscale plates based on the modified couple stress theory in which an internal material length scale parameter is included. Unlike the ...A non-classical Kirchhoff plate model is developed for the dynamic analysis of microscale plates based on the modified couple stress theory in which an internal material length scale parameter is included. Unlike the classical Kirchhoff plate model, the newly developed model can capture the size effect of microscale plates. Two boundary value problems of rectangular micro- plates are solved and the size effect on the lowest two natural frequencies is investigated. It is shown that the natural frequencies of the microscale plates predicted by the current model are size-dependent when the plate thickness is comparable to the material length scale parameter.展开更多
Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,f...Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,few documents on optimum design for multi-layer shrink-fit vessels made of different strength materials can be found,available data are mainly on two-layer vessels.In this paper,an optimum design approach is developed for shrink-fit multi-layer vessels under ultrahigh pressure by using different materials.Maximum shear stress theory is applied as design criteria.The inner and outer radii of a multi-layer vessel,as well as the material of each layer,are assumed to be known.The optimization mathematical model is,thereby,built.Lagrange multipliers method is required to obtain the optimal design formula of wall ratio（ratio of outer to inner radii） of each layer,from which the optimum formulas of shrinkage pressure and radial interference are derived with the superposition principle employed.These formulas are applicable for the optimization design of all multi-layer vessels made of different materials,or same materials.The formulas of the limit working pressure and the contact pressure show that the optimum wall ratio of each layer and limit working pressure are only related to all selected material strength and unrelated to the position of the layer placement in the vessel.However,shrinkage pressure is related to the position of the layer placement in the vessel.Optimization design of an open ended shrink-fit three-layer vessel using different materials and comparisons proved that the optimized multi-layer vessels have outstanding characteristics of small radial interference and are easier for assembly.When the stress of each layer is distributed more evenly and appropriately,the load bearing capability and safety of vessels are enhanced.Therefore,this design is material-saving and cost-effective,and has prospect of engineering application.展开更多
Based on the Modified Couple Stress Theory,a functionally graded micro-beam under electrostatic forces is studied.The FGM micro-beam is made of two materials and material properties vary continuously along the beam th...Based on the Modified Couple Stress Theory,a functionally graded micro-beam under electrostatic forces is studied.The FGM micro-beam is made of two materials and material properties vary continuously along the beam thickness according to a power-law.Dynamic and static pull-in voltages are obtained and it is shown that the static and dynamic pull-in voltages for some materials cannot be obtained using classic theories and components of couple stress must be taken into account.In addition,it is shown that the values of pull-in voltages depend on the variation through the thickness of the volume fractions of the two constituents.展开更多
The size-dependent effect on the biaxial and shear nonlinear buckling analysis of an isotropic and orthotropic micro-plate based on the surface stress, the modified couple stress theory （MCST）, and the nonlocal elas...The size-dependent effect on the biaxial and shear nonlinear buckling analysis of an isotropic and orthotropic micro-plate based on the surface stress, the modified couple stress theory （MCST）, and the nonlocal elasticity theories using the differential quadrature method （DQM） is presented. Main advantages of the MCST over the classical theory （CT） are the inclusion of the asymmetric couple stress tensor and the consideration of only one material length scale parameter. Based on the nonlinear von Karman assumption, the governing equations of equilibrium for the micro-classical plate consid- ering midplane displacements are derived based on the minimum principle of potential energy. Using the DQM, the biaxial and shear critical buckling loads of the micro-plate for various boundary conditions are obtained. Accuracy of the obtained results is validated by comparing the solutions with those reported in the literature. A parametric study is conducted to show the effects of the aspect ratio, the side-to-thickness ratio, Eringen＇s nonlocal parameter, the material length scale parameter, Young＇s modulus of the surface layer, the surface residual stress, the polymer matrix coefficients, and various boundary conditions on the dimensionless uniaxial, biaxial, and shear critical buckling loads. The results indicate that the critical buckling loads are strongly sensitive to Eringen＇s nonlocal parameter, the material length scale parameter, and the surface residual stress effects, while the effect of Young＇s modulus of the surface layer on the critical buckling load is negligible. Also, considering the size dependent effect causes the increase in the stiffness of the orthotropic micro-plate. The results show that the critical biaxial buckling load increases with an increase in G12/E2 and vice versa for E1/E2. It is shown that the nonlinear biaxial buckling ratio decreases as the aspect ratio increases and vice versa for the buckling amplitude. Because of the most lightweight micro-composite materials with 展开更多
This paper studies the static deformation behavior of a piezoelectric micromachined ultrasonic transducer （PMUT） actuated by a strong external electric field. The transducer membrane consists of a piezoelectric laye...This paper studies the static deformation behavior of a piezoelectric micromachined ultrasonic transducer （PMUT） actuated by a strong external electric field. The transducer membrane consists of a piezoelectric layer, a passive layer and two electrode layers. The nonlinearities of the piezoelectric layer caused by electrostriction under a strong electric field are analyzed. Because the thickness of the transducer membrane is on the microscale, the size dependence of the deformation behavior is evaluated using the couple stress theory. The results show that the optimal ratio of the top electrode diameter and the membrane diameter is around 0.674. It is also found that this optimal value does not depend on any other parameters if the thicknesses of the two electrodes are negligible compared with those of the piezo- electric and passive layers. In addition, the nonlinearities of the piezoelectric layer will become stronger along with the increase of the electric field, which means that softening of the membrane stiffness occurs when a strong external electric field is applied. Meanwhile, the optimal thickness ratio for the passive layer and the piezoelectric layer is not equal to 1.0 which is usually adopted by previous researchers. Because there exists size dependence of membrane deforma-tion, the optimal value of this thickness ratio needs to be greater than 1.0 on the microscale.展开更多
The objective of this paper is to model the size-dependent thermo-mechanical behaviors of a shape memory polymer (SMP) microbeam.Size-dependent constitutive equations,which can capture the size effect of the SMP,are p...The objective of this paper is to model the size-dependent thermo-mechanical behaviors of a shape memory polymer (SMP) microbeam.Size-dependent constitutive equations,which can capture the size effect of the SMP,are proposed based on the modified couple stress theory (MCST).The deformation energy expression of the SMP microbeam is obtained by employing the proposed size-dependent constitutive equation and Bernoulli-Euler beam theory.An SMP microbeam model,which includes the formulations of deflection,strain,curvature,stress and couple stress,is developed by using the principle of minimum potential energy and the separation of variables together.The sizedependent thermo-mechanical and shape memory behaviors of the SMP microbeam and the influence of the Poisson ratio are numerically investigated according to the developed SMP microbeam model.Results show that the size effects of the SMP microbeam are significant when the dimensionless height is small enough.However,they are too slight to be necessarily considered when the dimensionless height is large enough.The bending flexibility and stress level of the SMP microbeam rise with the increasing dimensionless height,while the couple stress level declines with the increasing dimensionless height.The larger the dimensionless height is,the more obvious the viscous property and shape memory effect of the SMP microbeam are.The Poisson ratio has obvious influence on the size-dependent behaviors of the SMP microbeam.The paper provides a theoretical basis and a quantitatively analyzing tool for the design and analysis of SMP micro-structures in the field of biological medicine,microelectronic devices and micro-electro-mechanical system (MEMS) self-assembling.展开更多
In this study, a size-dependent composite laminated skew Mindlin plate model is proposed based on a new modified couple stress theory. This plate model can be viewed as a simplified couple stress theory in engineering...In this study, a size-dependent composite laminated skew Mindlin plate model is proposed based on a new modified couple stress theory. This plate model can be viewed as a simplified couple stress theory in engineering mechanics. Governing equations and related boundary conditions are derived based on the principle of minimum potential energy. The Rayleigh–Ritz method is employed to obtain the numerical solutions of the center deflections of simply supported plates with different ply orientations. Numerical results show that the normalized center deflections obtained by the proposed model are always smaller than those obtained by the classical one, i.e. the present model can capture the scale effects of microstructures. Moreover, a phenomenon reveals that the ply orientation would make a significant influence on the magnitude of scale effects of composite laminated plates at micro scale. Additionally, the present model of thick skew plate can be degenerated to the model of Kirchhoff plate based on the modified couple stress theory by adopting the assumptions in Bernoulli–Euler beam and material isotropy.展开更多
In this study, a model for dynamic instability of embedded single-walled car- bon nanotubes （SWCNTs） is presented. SWCNTs are modeled by the sinusoidal shear deformation beam theory （SSDBT）. The modified couple st...In this study, a model for dynamic instability of embedded single-walled car- bon nanotubes （SWCNTs） is presented. SWCNTs are modeled by the sinusoidal shear deformation beam theory （SSDBT）. The modified couple stress theory （MCST） is con- sidered in order to capture the size effects. The surrounding elastic medium is described by a visco-Pasternak foundation model, which accounts for normal, transverse shear, and damping loads. The motion equations are derived based on Hamilton＇s principle. The differential quadrature method （DQM） in conjunction with the Bolotin method is used in order to calculate the dynamic instability region （DIR） of SWCNTs. The effects of differ- ent parameters, such as nonlocal parameter, visco-Pasternak foundation, mode numbers, and geometrical parameters, are shown on the dynamic instability of SWCNTs. The re- sults depict that increasing the nonlocal parameter shifts the DIR to right. The results presented in this paper would be helpful in design and manufacturing of nano-electromechanical system （NEMS） and micro-electro-mechanical system （MEMS）.展开更多
An approximate analytical model for calculating the pull-in voltage of a stepped cantilever-type radio frequency （RF） micro electro-mechanical system （MEMS） switch is developed based on the Euler-Bernoulli beam an...An approximate analytical model for calculating the pull-in voltage of a stepped cantilever-type radio frequency （RF） micro electro-mechanical system （MEMS） switch is developed based on the Euler-Bernoulli beam and a modified couple stress theory, and is validated by comparison with the finite element results. The sensitivity functions of the pull-in voltage to the designed parameters are derived based on the proposed model. The sensitivity investigation shows that the pull-in voltage sensitivities increase/decrease nonlinearly with the increases in the designed parameters. For the stepped cantilever beam, there exists a nonzero optimal dimensionless length ratio, where the pull-in voltage is insensitive. The optimal value of the dimensionless length ratio only depends on the dimensionless width ratio, and can be obtained by solving a nonlinear equation. The determination of the designed parameters is discussed, and some recommendations are made for the RF MEMS switch optimization.展开更多
文摘The purpose is to reestablish the balance laws of momentum, angular momentum and energy and to derive the corresponding local and nonlocal balance equations for micromorphic continuum mechanics and couple stress theory. The desired results for micromorphic continuum mechanics and couple stress theory are naturally obtained via direct transitions and reductions from the coupled conservation law of energy for micropolar continuum theory, respectively. The basic balance laws and equations for micromorphic continuum mechanics and couple stress theory are constituted by combining these results derived here and the traditional conservation laws and equations of mass and microinertia and the entropy inequality. The incomplete degrees of the former related continuum theories are clarified. Finally, some special cases are conveniently derived.
文摘The linear and nonlinear torsional free vibration analyses of functionMly graded micro/nuno-tubes （FGMTs） are analytically investigated based on the couple stress theory. The employed non-classical continuum theory contains one material length scale parameter, which can capture the small scale effect. The FGMT model accounts for the through-radius power-law variation of a two-constituent material. Hamilton＇s principle is used to develop the non-classical nonlinear governing equation. To study the effect of the boundary conditions, two types of end conditions, i.e., fixed-fixed and fixed-free, are considered. The derived boundary value governing equation is of the fourthorder, and is solved by the homotopy analysis method （HAM）. This method is based on the Taylor series with an embedded parameter and is capable of providing very good approximations by means of only a few terms, if the initial guess and the auxiliary linear operator are properly selected. The analytical expressions are developed for the linear and nonlinear natural frequencies, which can be conveniently used to investigate the effects of the dimensionless length scale parameter, the material gradient index, and the vibration amplitude on the natural frequencies of FGMTs.
基金was supported by the National Natural Science Foundation of China (Grant No. 10672032)
文摘Among many theories and categories in microstructures,rotation-displacement used as "independent" or "dependent" variables,is a noticeable topic. In FEM,it is called C0 and C1 theory. The convergence criteria of finite elements for microstructures are less mature than those for the conventional thin plate bending problem. In this paper,the patch test functions for assessing convergence of the C0 and C1 finite elements in microstructures is established based on the enhanced patch test theory. The author has further explored the C0 and C1 finite element theories and investigated the difference and correlation between their finite element formulations. Newly proposed finite element theories for microstructures are as follows:(1) the displacement-rotation dependent C1 element that requires the element function satisfying both C0 and C1 continuity;(2) the displacement-rotation independent C0 element which requires new convergence criteria,such as non-zero constant shear stress patch test and zero constant shear stress patch test for approximating C1 element.
基金Supported by the National Natural Science Foundation of China (Grant No. 10672032)
文摘The enhanced patch test proposed by Chen W J(2006) can be used to assess the convergence of the problem with non-homogeneous differential equations.Based on this theory,we establish the patch test function for axisymmetric elements of conventional and couple stress theories,and reach an important conclusion that the patch test function for axisymmetric elements cannot contain non-zero constant shear.
文摘A non-classical Kirchhoff plate model is developed for the dynamic analysis of microscale plates based on the modified couple stress theory in which an internal material length scale parameter is included. Unlike the classical Kirchhoff plate model, the newly developed model can capture the size effect of microscale plates. Two boundary value problems of rectangular micro- plates are solved and the size effect on the lowest two natural frequencies is investigated. It is shown that the natural frequencies of the microscale plates predicted by the current model are size-dependent when the plate thickness is comparable to the material length scale parameter.
基金supported by Key Scientific Research Project of Baoji University of Arts and Sciences of China (Grant No.ZK0727)Shanxi Provincial Special Foundation Project of Key Discipline Construction of China
文摘Multi-layer pressure vessels are widely used in every field of high pressure technology.For the purpose of enhancing a vessels＇ load bearing capacity,a beneficial process like shrink-fit is usually employed.However,few documents on optimum design for multi-layer shrink-fit vessels made of different strength materials can be found,available data are mainly on two-layer vessels.In this paper,an optimum design approach is developed for shrink-fit multi-layer vessels under ultrahigh pressure by using different materials.Maximum shear stress theory is applied as design criteria.The inner and outer radii of a multi-layer vessel,as well as the material of each layer,are assumed to be known.The optimization mathematical model is,thereby,built.Lagrange multipliers method is required to obtain the optimal design formula of wall ratio（ratio of outer to inner radii） of each layer,from which the optimum formulas of shrinkage pressure and radial interference are derived with the superposition principle employed.These formulas are applicable for the optimization design of all multi-layer vessels made of different materials,or same materials.The formulas of the limit working pressure and the contact pressure show that the optimum wall ratio of each layer and limit working pressure are only related to all selected material strength and unrelated to the position of the layer placement in the vessel.However,shrinkage pressure is related to the position of the layer placement in the vessel.Optimization design of an open ended shrink-fit three-layer vessel using different materials and comparisons proved that the optimized multi-layer vessels have outstanding characteristics of small radial interference and are easier for assembly.When the stress of each layer is distributed more evenly and appropriately,the load bearing capability and safety of vessels are enhanced.Therefore,this design is material-saving and cost-effective,and has prospect of engineering application.
文摘Based on the Modified Couple Stress Theory,a functionally graded micro-beam under electrostatic forces is studied.The FGM micro-beam is made of two materials and material properties vary continuously along the beam thickness according to a power-law.Dynamic and static pull-in voltages are obtained and it is shown that the static and dynamic pull-in voltages for some materials cannot be obtained using classic theories and components of couple stress must be taken into account.In addition,it is shown that the values of pull-in voltages depend on the variation through the thickness of the volume fractions of the two constituents.
基金supported by the Iranian Nanotechnology Development Committee and the University of Kashan(No.363452/10)
文摘The size-dependent effect on the biaxial and shear nonlinear buckling analysis of an isotropic and orthotropic micro-plate based on the surface stress, the modified couple stress theory （MCST）, and the nonlocal elasticity theories using the differential quadrature method （DQM） is presented. Main advantages of the MCST over the classical theory （CT） are the inclusion of the asymmetric couple stress tensor and the consideration of only one material length scale parameter. Based on the nonlinear von Karman assumption, the governing equations of equilibrium for the micro-classical plate consid- ering midplane displacements are derived based on the minimum principle of potential energy. Using the DQM, the biaxial and shear critical buckling loads of the micro-plate for various boundary conditions are obtained. Accuracy of the obtained results is validated by comparing the solutions with those reported in the literature. A parametric study is conducted to show the effects of the aspect ratio, the side-to-thickness ratio, Eringen＇s nonlocal parameter, the material length scale parameter, Young＇s modulus of the surface layer, the surface residual stress, the polymer matrix coefficients, and various boundary conditions on the dimensionless uniaxial, biaxial, and shear critical buckling loads. The results indicate that the critical buckling loads are strongly sensitive to Eringen＇s nonlocal parameter, the material length scale parameter, and the surface residual stress effects, while the effect of Young＇s modulus of the surface layer on the critical buckling load is negligible. Also, considering the size dependent effect causes the increase in the stiffness of the orthotropic micro-plate. The results show that the critical biaxial buckling load increases with an increase in G12/E2 and vice versa for E1/E2. It is shown that the nonlinear biaxial buckling ratio decreases as the aspect ratio increases and vice versa for the buckling amplitude. Because of the most lightweight micro-composite materials with
基金supported by the National Natural Science Foundation of China (11172138, 10727201)
文摘This paper studies the static deformation behavior of a piezoelectric micromachined ultrasonic transducer （PMUT） actuated by a strong external electric field. The transducer membrane consists of a piezoelectric layer, a passive layer and two electrode layers. The nonlinearities of the piezoelectric layer caused by electrostriction under a strong electric field are analyzed. Because the thickness of the transducer membrane is on the microscale, the size dependence of the deformation behavior is evaluated using the couple stress theory. The results show that the optimal ratio of the top electrode diameter and the membrane diameter is around 0.674. It is also found that this optimal value does not depend on any other parameters if the thicknesses of the two electrodes are negligible compared with those of the piezo- electric and passive layers. In addition, the nonlinearities of the piezoelectric layer will become stronger along with the increase of the electric field, which means that softening of the membrane stiffness occurs when a strong external electric field is applied. Meanwhile, the optimal thickness ratio for the passive layer and the piezoelectric layer is not equal to 1.0 which is usually adopted by previous researchers. Because there exists size dependence of membrane deforma-tion, the optimal value of this thickness ratio needs to be greater than 1.0 on the microscale.
基金Project supported by the National Key Research and Development Program of China(No.2017YFC0307604)the Talent Foundation of China University of Petroleum(No.Y1215042)the Graduate Innovation Program of China University of Petroleum(East China)(No.YCX2019084)
文摘The objective of this paper is to model the size-dependent thermo-mechanical behaviors of a shape memory polymer (SMP) microbeam.Size-dependent constitutive equations,which can capture the size effect of the SMP,are proposed based on the modified couple stress theory (MCST).The deformation energy expression of the SMP microbeam is obtained by employing the proposed size-dependent constitutive equation and Bernoulli-Euler beam theory.An SMP microbeam model,which includes the formulations of deflection,strain,curvature,stress and couple stress,is developed by using the principle of minimum potential energy and the separation of variables together.The sizedependent thermo-mechanical and shape memory behaviors of the SMP microbeam and the influence of the Poisson ratio are numerically investigated according to the developed SMP microbeam model.Results show that the size effects of the SMP microbeam are significant when the dimensionless height is small enough.However,they are too slight to be necessarily considered when the dimensionless height is large enough.The bending flexibility and stress level of the SMP microbeam rise with the increasing dimensionless height,while the couple stress level declines with the increasing dimensionless height.The larger the dimensionless height is,the more obvious the viscous property and shape memory effect of the SMP microbeam are.The Poisson ratio has obvious influence on the size-dependent behaviors of the SMP microbeam.The paper provides a theoretical basis and a quantitatively analyzing tool for the design and analysis of SMP micro-structures in the field of biological medicine,microelectronic devices and micro-electro-mechanical system (MEMS) self-assembling.
基金supported by the National Natural Sciences Foundation of China(No.11572204)
文摘In this study, a size-dependent composite laminated skew Mindlin plate model is proposed based on a new modified couple stress theory. This plate model can be viewed as a simplified couple stress theory in engineering mechanics. Governing equations and related boundary conditions are derived based on the principle of minimum potential energy. The Rayleigh–Ritz method is employed to obtain the numerical solutions of the center deflections of simply supported plates with different ply orientations. Numerical results show that the normalized center deflections obtained by the proposed model are always smaller than those obtained by the classical one, i.e. the present model can capture the scale effects of microstructures. Moreover, a phenomenon reveals that the ply orientation would make a significant influence on the magnitude of scale effects of composite laminated plates at micro scale. Additionally, the present model of thick skew plate can be degenerated to the model of Kirchhoff plate based on the modified couple stress theory by adopting the assumptions in Bernoulli–Euler beam and material isotropy.
文摘In this study, a model for dynamic instability of embedded single-walled car- bon nanotubes （SWCNTs） is presented. SWCNTs are modeled by the sinusoidal shear deformation beam theory （SSDBT）. The modified couple stress theory （MCST） is con- sidered in order to capture the size effects. The surrounding elastic medium is described by a visco-Pasternak foundation model, which accounts for normal, transverse shear, and damping loads. The motion equations are derived based on Hamilton＇s principle. The differential quadrature method （DQM） in conjunction with the Bolotin method is used in order to calculate the dynamic instability region （DIR） of SWCNTs. The effects of differ- ent parameters, such as nonlocal parameter, visco-Pasternak foundation, mode numbers, and geometrical parameters, are shown on the dynamic instability of SWCNTs. The re- sults depict that increasing the nonlocal parameter shifts the DIR to right. The results presented in this paper would be helpful in design and manufacturing of nano-electromechanical system （NEMS） and micro-electro-mechanical system （MEMS）.
基金supported by the National Natural Science Foundation of China(Nos.51505089 and61204116)the Opening Project of the Science and Technology on Reliability Physics and Application Technology of Electronic Component Laboratory(Nos.ZHD201207 and 9140C030605140C03015)the Pearl River S&T Nova Program of Guangzhou(No.2014J2200086)
文摘An approximate analytical model for calculating the pull-in voltage of a stepped cantilever-type radio frequency （RF） micro electro-mechanical system （MEMS） switch is developed based on the Euler-Bernoulli beam and a modified couple stress theory, and is validated by comparison with the finite element results. The sensitivity functions of the pull-in voltage to the designed parameters are derived based on the proposed model. The sensitivity investigation shows that the pull-in voltage sensitivities increase/decrease nonlinearly with the increases in the designed parameters. For the stepped cantilever beam, there exists a nonzero optimal dimensionless length ratio, where the pull-in voltage is insensitive. The optimal value of the dimensionless length ratio only depends on the dimensionless width ratio, and can be obtained by solving a nonlinear equation. The determination of the designed parameters is discussed, and some recommendations are made for the RF MEMS switch optimization.
