A continuous unidirectional solidification equipment with the advantages of electric slag remelting, induction heating, continuous casting and unidirectional solidification was built to study the QAl9 4 Cu Al alloy. T...A continuous unidirectional solidification equipment with the advantages of electric slag remelting, induction heating, continuous casting and unidirectional solidification was built to study the QAl9 4 Cu Al alloy. The results show that the electro slag induction continuous unidirectional solidification process can be used for the steady continuous unidirectional solidification of QAl9 4, and revitalizes the down pulling continuous unidirectional solidification process; that the temperature distribution in the mold wall reflects that of the molten metal in the mold, thus the temperature distribution in the mold wall can be used to control the electric slag induction continuous unidirectional solidification process; and that the mutual matching of the technological parameters is the key to stabilize the solidification process.展开更多
The study area is located in the east Tabas Block in Central Iran. Facies analysis of the Qal＇eh Dokhtar Formation（middle Callovian to late Oxfordian） was carried out on two stratigraphic sections and applied to de...The study area is located in the east Tabas Block in Central Iran. Facies analysis of the Qal＇eh Dokhtar Formation（middle Callovian to late Oxfordian） was carried out on two stratigraphic sections and applied to depositional environment and sequence stratigraphy interpretation. This formation conformably overlies and underlies the marly-silty Baghamshah and the calcareous Esfandiar formations, respectively. Lateral and vertical facies changes documents low-to high energy environments, including tidal-flat, beach to intertidal, lagoon, barrier, and open-marine. According to these facies associations and absence of resedimentation deposits a depositional model of a mixed carbonate-siliciclastic ramp was proposed for the Qal＇eh Dokhtar Formation. Seven third-order depositional sequences were identified in each two measured stratigraphic sections. Transgressive systems tracts（TSTs） show deepening upward trends, i.e. shallow water beach to intertidal and lagoonal facies, while highstand systems tracts（HST） show shallowing upward trends in which deep water facies are overlain by shallow water facies. All sequence boundaries（except at the base of the stratigraphic column） are of the no erosional（SB2） types. We conclude eustatic rather than tectonic factors played a dominant role in controlling carbonate depositional environments in the study area.展开更多
The erosion behavior of a QA19-4 alloy as a ship propeller material was investigated.The effects of the solution,the impact angles and the sand content were considered.The test results demonstrate that the mass loss o...The erosion behavior of a QA19-4 alloy as a ship propeller material was investigated.The effects of the solution,the impact angles and the sand content were considered.The test results demonstrate that the mass loss of the alloy in 3.5 wt%NaCl solution is 1.35 times that in tap water,due to the corrosive effect of Cl^(-).The mass loss of the alloy increases as the impact angle increases up to~30°and consequently decreases as the impact angle increases.Also,this feature is typical for the ductile metal behavior.At the impact angle of 0°,this feature is associated with the predominant erosion mechanisms,such as shallow plowing and surface fatigue;at 30°,this feature is micro-cutting,deep plowing and surface fatigue;and at 45°,it becomes indentation accompanied by extruded lips.The mass loss and surface roughness of the alloy increase as the sand content increases under the testing conditions.展开更多
文摘A continuous unidirectional solidification equipment with the advantages of electric slag remelting, induction heating, continuous casting and unidirectional solidification was built to study the QAl9 4 Cu Al alloy. The results show that the electro slag induction continuous unidirectional solidification process can be used for the steady continuous unidirectional solidification of QAl9 4, and revitalizes the down pulling continuous unidirectional solidification process; that the temperature distribution in the mold wall reflects that of the molten metal in the mold, thus the temperature distribution in the mold wall can be used to control the electric slag induction continuous unidirectional solidification process; and that the mutual matching of the technological parameters is the key to stabilize the solidification process.
基金financial support given to this study by the Department of Geology of Ferdowsi University of Mashhad, Iran (code 3/28001)
文摘The study area is located in the east Tabas Block in Central Iran. Facies analysis of the Qal＇eh Dokhtar Formation（middle Callovian to late Oxfordian） was carried out on two stratigraphic sections and applied to depositional environment and sequence stratigraphy interpretation. This formation conformably overlies and underlies the marly-silty Baghamshah and the calcareous Esfandiar formations, respectively. Lateral and vertical facies changes documents low-to high energy environments, including tidal-flat, beach to intertidal, lagoon, barrier, and open-marine. According to these facies associations and absence of resedimentation deposits a depositional model of a mixed carbonate-siliciclastic ramp was proposed for the Qal＇eh Dokhtar Formation. Seven third-order depositional sequences were identified in each two measured stratigraphic sections. Transgressive systems tracts（TSTs） show deepening upward trends, i.e. shallow water beach to intertidal and lagoonal facies, while highstand systems tracts（HST） show shallowing upward trends in which deep water facies are overlain by shallow water facies. All sequence boundaries（except at the base of the stratigraphic column） are of the no erosional（SB2） types. We conclude eustatic rather than tectonic factors played a dominant role in controlling carbonate depositional environments in the study area.
基金financially supported by the National Natural Science Foundation of China(No.51171216)the National"Ten Thousand Plan"Scientific and Technological Innovation Leading Talent Project。
文摘The erosion behavior of a QA19-4 alloy as a ship propeller material was investigated.The effects of the solution,the impact angles and the sand content were considered.The test results demonstrate that the mass loss of the alloy in 3.5 wt%NaCl solution is 1.35 times that in tap water,due to the corrosive effect of Cl^(-).The mass loss of the alloy increases as the impact angle increases up to~30°and consequently decreases as the impact angle increases.Also,this feature is typical for the ductile metal behavior.At the impact angle of 0°,this feature is associated with the predominant erosion mechanisms,such as shallow plowing and surface fatigue;at 30°,this feature is micro-cutting,deep plowing and surface fatigue;and at 45°,it becomes indentation accompanied by extruded lips.The mass loss and surface roughness of the alloy increase as the sand content increases under the testing conditions.
