与传统的雾化制粉技术不同,电极感应熔炼气体雾化(EIGA)技术是采用预合金棒料为电极,无坩埚感应加热,熔化后直接滴落雾化区被惰性气体雾化的技术.该技术由于在熔炼过程中液态金属与坩埚不接触,有效地减少了钛合金粉末中的夹杂物,改善了...与传统的雾化制粉技术不同,电极感应熔炼气体雾化(EIGA)技术是采用预合金棒料为电极,无坩埚感应加热,熔化后直接滴落雾化区被惰性气体雾化的技术.该技术由于在熔炼过程中液态金属与坩埚不接触,有效地减少了钛合金粉末中的夹杂物,改善了合金粉末的质量.本文利用自主设计制造的EIGA制粉设备,采用激光粒度分析仪、扫描电镜(SEM)、X射线衍射仪(XRD)等分析手段,研究了不同功率参数对雾化制备TC4合金粉末的粒度分布、组织形貌、空心球等的影响.研究表明:EIGA法制备的TC4合金粉末整体球形度均较好,空心球缺陷较少,空心球率低于3%.熔炼功率较低时,粗颗粒粉末较多,且存在一定比例不规则的棒形和哑铃状粉末颗粒;当功率提高到62 k W时,细粉比例明显提高,不规则形状的粉末颗粒基本消失.随着功率的升高,粉末中的氧含量呈增加趋势,但仍基本保持在0.08%~0.10%较低范围内.功率为56 k W时,粉末松装密度最好,为2.686 g/cm3,松装密度比为60.63%,符合激光3D打印用TC4钛合金粉末松装密度比要求.展开更多
利用 FS-Ⅰ,T-100做分散剂,无水乙醇做连续相溶液建立分散体系,分別对超细磁性羰基 Fe 粉和激光制 SiC、Si_3N_4超细粉进行分散。在 TEM 下观察,羰基 Fe 粉分散度高于70%,SiC 粉高于80%,Si_3N_4粉高于95%。经照相记录和采用 CSR-40图像...利用 FS-Ⅰ,T-100做分散剂,无水乙醇做连续相溶液建立分散体系,分別对超细磁性羰基 Fe 粉和激光制 SiC、Si_3N_4超细粉进行分散。在 TEM 下观察,羰基 Fe 粉分散度高于70%,SiC 粉高于80%,Si_3N_4粉高于95%。经照相记录和采用 CSR-40图像分析系统进行粒度统计,得到三种粉的粒度对数正态分布。羰基 Fe 粉粒度分布12—70nm,SiC 粉粒度分布20—110nm,Si_3N_4粉粒度分布2.5—26nm。讨论了不同分散剂和分散测量方法对分散程度的影响。展开更多
Gas atomization is now an important production technique for Fe-based amorphous alloy powders used in additive manufacturing,particularly selective laser melting,fabricating large-sized Fe-based bulk metallic glasses....Gas atomization is now an important production technique for Fe-based amorphous alloy powders used in additive manufacturing,particularly selective laser melting,fabricating large-sized Fe-based bulk metallic glasses.Using the realizable k-εmodel and discrete phase model theory,the flow dynamics of the gas phase and gas-melt two-phase flow felds in the close-wake condition were investigated to establish the correlation between high gas pressure and powder particle characteristics.The locations of the recirculation zones and the shapes of Mach disks were analyzed in detail for the type of discrete-jet closed-coupled gas atomization nozzle.In the gas-phase flow feld,the vortexes,closed to the Mach disk,are found to be a new deceleration method.In the two-phase flow feld,the shape of Mach disk changes from“S”-shape to“Z”-shape under the impact of the droplet flow.As predicted by the wave model,with the elevation of gas pressure,the size of the particle is found to gradually decrease and its distribution becomes more concentrated.Simulation results were compliant with the Fe-based amorphous alloy powder preparation tests.This study deepens the understanding of the gas pressure impacting particle features via gas atomization,and contributes to technological applications.展开更多
文摘与传统的雾化制粉技术不同,电极感应熔炼气体雾化(EIGA)技术是采用预合金棒料为电极,无坩埚感应加热,熔化后直接滴落雾化区被惰性气体雾化的技术.该技术由于在熔炼过程中液态金属与坩埚不接触,有效地减少了钛合金粉末中的夹杂物,改善了合金粉末的质量.本文利用自主设计制造的EIGA制粉设备,采用激光粒度分析仪、扫描电镜(SEM)、X射线衍射仪(XRD)等分析手段,研究了不同功率参数对雾化制备TC4合金粉末的粒度分布、组织形貌、空心球等的影响.研究表明:EIGA法制备的TC4合金粉末整体球形度均较好,空心球缺陷较少,空心球率低于3%.熔炼功率较低时,粗颗粒粉末较多,且存在一定比例不规则的棒形和哑铃状粉末颗粒;当功率提高到62 k W时,细粉比例明显提高,不规则形状的粉末颗粒基本消失.随着功率的升高,粉末中的氧含量呈增加趋势,但仍基本保持在0.08%~0.10%较低范围内.功率为56 k W时,粉末松装密度最好,为2.686 g/cm3,松装密度比为60.63%,符合激光3D打印用TC4钛合金粉末松装密度比要求.
文摘利用 FS-Ⅰ,T-100做分散剂,无水乙醇做连续相溶液建立分散体系,分別对超细磁性羰基 Fe 粉和激光制 SiC、Si_3N_4超细粉进行分散。在 TEM 下观察,羰基 Fe 粉分散度高于70%,SiC 粉高于80%,Si_3N_4粉高于95%。经照相记录和采用 CSR-40图像分析系统进行粒度统计,得到三种粉的粒度对数正态分布。羰基 Fe 粉粒度分布12—70nm,SiC 粉粒度分布20—110nm,Si_3N_4粉粒度分布2.5—26nm。讨论了不同分散剂和分散测量方法对分散程度的影响。
基金supported by the National Key Research and Development Program of China(No.2016YFB1100204)the Key Research&Development Plan of Jiangxi Province(No.20192ACB80001)the National Natural Science Foundation of China(Nos.52171163,51701214 and U1908219)。
文摘Gas atomization is now an important production technique for Fe-based amorphous alloy powders used in additive manufacturing,particularly selective laser melting,fabricating large-sized Fe-based bulk metallic glasses.Using the realizable k-εmodel and discrete phase model theory,the flow dynamics of the gas phase and gas-melt two-phase flow felds in the close-wake condition were investigated to establish the correlation between high gas pressure and powder particle characteristics.The locations of the recirculation zones and the shapes of Mach disks were analyzed in detail for the type of discrete-jet closed-coupled gas atomization nozzle.In the gas-phase flow feld,the vortexes,closed to the Mach disk,are found to be a new deceleration method.In the two-phase flow feld,the shape of Mach disk changes from“S”-shape to“Z”-shape under the impact of the droplet flow.As predicted by the wave model,with the elevation of gas pressure,the size of the particle is found to gradually decrease and its distribution becomes more concentrated.Simulation results were compliant with the Fe-based amorphous alloy powder preparation tests.This study deepens the understanding of the gas pressure impacting particle features via gas atomization,and contributes to technological applications.
