The performance of LiNi/γ-Al2O3 catalysts modified by rare earth metal oxide （La2O3 or CeO2） packed on BCFNO membrane reactor was discussed for the partial oxidation of methane （POM） in coke oven gas （COG） at 8...The performance of LiNi/γ-Al2O3 catalysts modified by rare earth metal oxide （La2O3 or CeO2） packed on BCFNO membrane reactor was discussed for the partial oxidation of methane （POM） in coke oven gas （COG） at 875 ℃. The NiO/γ-Al2O3 catalysts with different amounts of La2O3 and CeO2 were prepared with the same preparation method and under the same condition in order to compare the reaction performance （oxygen permeation, CH4 conversion, H2 and CO selectivity） on the membrane reactor. The results show that the oxygen permeation flux increased significantly with LiNiREOx/γ-Al2O3 （RE = La or Ce） catalysts by adding the element of rare earth especially the Ce during the POM in COG. Such as, the Li15wt%CeO29wt%NiO/γ-Al2O3 catalyst with an oxygen permeation flux of 24.71 ml·cm^-2·min^-1 and a high CH4 conversion was obtained in 875 ℃. The resulted high oxygen permeation flux may be due to the added Ce that inhibited the strong interaction between Ni and Al2O3 to form the NiAl2O4 phase. In addition, the introduction of Ce leads up to an important property of storing and releasing oxygen.展开更多
In order to improve the surface hardness and wear resistance of Ti and Ti alloy components, an oxygen permeation treatment (OPT) was developed. The oxygen permeation behaviors of three Ti alloys, TA2, TB5 and TC11, tr...In order to improve the surface hardness and wear resistance of Ti and Ti alloy components, an oxygen permeation treatment (OPT) was developed. The oxygen permeation behaviors of three Ti alloys, TA2, TB5 and TC11, treated in air with O-P medium at high temperature have been studied. The results show that the 0-P treatment can significantly improve the surface hardness of Ti alloys. The oxidation mass-gain of β-Ti alloy (TB5) is much higher than α-Ti alloy (TA2) under the same condition, while α+β Ti alloy (TC11) is the lowest. All the Ti alloys treated at this condition produce two surface layers: the outer layer consists mainly of TiO2, as well as trace of other oxides, and the inner layer consists of a Ti-O interstitial solid solution formed by the diffusion of oxygen in α crystal lattice. Thick scales of β Ti alloy (TB5) are easily formed depending mainly on the poor solid solution content of oxygen, while deep solution layer can be formed since partial β phase has been transformed into α phase. The scales of α-β Ti alloy (TC11) are very thin and compact. Aluminum-rich zone, as well as deficient zone, is found in oxide layers. A crystallographic characterization of oxygen solution layer has been performed and evaluated by crystallographic lattice constant.展开更多
Perovskite-type oxygen-permeable membrane reactors of BaCo0.7Fe0.2Nb0.1O3-δ （BCFNO） packed with Ru-based catalyst had high oxygen permeability and could be used for hydrogen production by partial oxidation of metha...Perovskite-type oxygen-permeable membrane reactors of BaCo0.7Fe0.2Nb0.1O3-δ （BCFNO） packed with Ru-based catalyst had high oxygen permeability and could be used for hydrogen production by partial oxidation of methane in coke oven gas （COG）. At 1173 K, 94% of methane conversion, 85% of H2 selectivity, 107% of CO selectivity, and as high as 15.4 mL·cm^-2·min^-1 of oxygen permeation flux were obtained. The BCFNO membrane itself had poor catalytic activity to partial oxidation of CH4 in COG. During continuous operation for 70 h at 1173 K, no degradation of the membrane reaction performance was observed. XRD and SEM characterization also demonstrated that the BCFNO membrane reactor exhibited good stability in partial oxidation of methane in COG.展开更多
Dual-phase membranes of 60 wt% Ce0.8Gd0.2O2-δ-40 wt% Pr Ba Co2exFexO3 d（0 x 2） were prepared by a combined citrate and ethylene diamine tetraacetic acid（EDTA） complexing method. X-ray diffraction（XRD）results re...Dual-phase membranes of 60 wt% Ce0.8Gd0.2O2-δ-40 wt% Pr Ba Co2exFexO3 d（0 x 2） were prepared by a combined citrate and ethylene diamine tetraacetic acid（EDTA） complexing method. X-ray diffraction（XRD）results revealed the good chemical compatibility between ion-conducting phase CGO and electron-conducting phases PBC2 xFxO after sintering in air. The Fe ionic dopant had a significant effect on the phase structure stability and oxygen permeability under CO2 atmosphere, which was confirmed by XRD, thermogravimetrye differential scanning calorimetry（TGeD SC）, scanning electron microscopy（SEM） and oxygen permeation experiments. CGOeP BC0.5F1.5O dual-phase membrane demonstrated a stable oxygen permeation flux of2.71x10-7mol cm 2s 1with 50 mol% He/CO2 as the sweep gas at 925 C, and this value was much higher than that of perovskite-type membranes. The rate-limiting step in the oxygen permeation process changed from the bulk diffusion to the surface oxygen exchange when the CGOeP BC0.5F1.5O membrane thickness decreased to 0.8 mm or less. Due to the high oxygen permeation fluxes and the excellent structural stability under CO2 atmosphere, the CGOeP BC0.5F1.5O membrane is a great potential candidate material for separating oxygen from air in the oxy-fuel combustion techniques.展开更多
Mixed oxygen-ionic and electronic conducting membranes of SrFe（Cu）O3-δ were prepared by solid-state reaction method. The crystal structure, oxygen nonstoichiometry, and phase stability of the materials were studied...Mixed oxygen-ionic and electronic conducting membranes of SrFe（Cu）O3-δ were prepared by solid-state reaction method. The crystal structure, oxygen nonstoichiometry, and phase stability of the materials were studied by TGA and XRD. Oxygen permeation fluxes through these membranes were studied at operating temperature ranging from 750 to 950 ℃. Results showed that doping Cu in SrFeO3-δ compound had a significant effect on the formation of single-phased perovskite structure. For SrFe1-xCu2O3-δ series materials, the oxygen nonstoichiometry and the oxygen permeation flux increased considerably with the increase of Cu-doping content （x = 0.1-0.3）. The sintering property of the membrane decreased significantly when the Cu substitution amount reached 40%. SrFe0.7Cu0.3O3-δ showed high oxygen permeation flux, but SrCuO2 and Sr2Fe2O5 phases formed in the compound after oxygen permeation test induced cracks in the membrane.展开更多
Novel mixed conducting oxides, B-site Bi-doped perovskites were exploited and synthesized. Cubic perovskite structures were formed for BaBi0.2COyFe0.8-yO3-δ (y≤0.4) and BaBixCo0.2Fe0.8-xO3-δ (x=0.1 -0.5). The mater...Novel mixed conducting oxides, B-site Bi-doped perovskites were exploited and synthesized. Cubic perovskite structures were formed for BaBi0.2COyFe0.8-yO3-δ (y≤0.4) and BaBixCo0.2Fe0.8-xO3-δ (x=0.1 -0.5). The materials exhibited considerable high oxygen permeability at high temperature. The oxygen permeation flux of BaBi0.2Co0.35Fe0.45O3-δmembrane reached about0.77×106 mol/cm2 ·s under an air/helium oxygen partial pressure gradient at 900 ℃, which was much higher than that of other bismuth-contained mixed conducting membranes. The permeation fluxes of the materials increased with the increase of cobalt content, but no apparent simple relationship was found with the bismuth content. The materials also demonstrated excellent reversibility of oxygen adsorption and desorption. Stable time-related oxygen permeation fluxes were found for BaBi0.2Co0.展开更多
Ba0.9R0.1Co0.TFe0.225Ta0.07503-δ （BRCFT, R = Ca, La or Sr） membranes were synthesized by a solid-state reaction. Metal cation Ca2＋, La3＋ or Sr2＋ doping on A-site partially substituted Ba2＋ in BaCoo.TFe0.225Ta0....Ba0.9R0.1Co0.TFe0.225Ta0.07503-δ （BRCFT, R = Ca, La or Sr） membranes were synthesized by a solid-state reaction. Metal cation Ca2＋, La3＋ or Sr2＋ doping on A-site partially substituted Ba2＋ in BaCoo.TFe0.225Ta0.07503-δ oxides, and its subsequent effects on phase structure stability, oxygen permeability and oxygen desorption were systematically investigated by XRD, TG-DSC, Hz-TPR, O2-TPD techniques and oxygen permeation experiments. The partial substitution with Ca2＋, La3＋ or Sr2＋, whose ionic radii are smaller than that of Ba2＋, succeeded in stabilizing the cubic perovskite structure without formation of impurity phases, as revealed by XRD analysis. Oxygen-involving experi- ments showed that BRCFT with A-site fully occupied by Ba2＋ exhibited good oxygen permeation flux under He flow, reaching about 2.3 mL.min-l .cm-2 at 900 with I mm thickness. Of all the membranes, BLCFT membrane showed better chemical stability in CO2, owing to the reduction in alkalinity of the mixed conductor oxide by La doping. In addition, we also found the stability of the perovskite structure under reducing atmospheres was strengthened by increasing the size of A-site cation （Ba2＋〉La3＋〉SrZ＋〉Ca2＋）.展开更多
基金supported by the National High Technology Research and Development Program of China (No. 2006AA11A189)Science and Technology Commission of Shanghai Municipality (No. 06DZ12212)+1 种基金National Engineering Research Center of Advanced Steel Technology (NERCAST) (No. 050209)the Innovation Fund for Graduate Studentof Shanghai University (SHUCX0910003)
文摘The performance of LiNi/γ-Al2O3 catalysts modified by rare earth metal oxide （La2O3 or CeO2） packed on BCFNO membrane reactor was discussed for the partial oxidation of methane （POM） in coke oven gas （COG） at 875 ℃. The NiO/γ-Al2O3 catalysts with different amounts of La2O3 and CeO2 were prepared with the same preparation method and under the same condition in order to compare the reaction performance （oxygen permeation, CH4 conversion, H2 and CO selectivity） on the membrane reactor. The results show that the oxygen permeation flux increased significantly with LiNiREOx/γ-Al2O3 （RE = La or Ce） catalysts by adding the element of rare earth especially the Ce during the POM in COG. Such as, the Li15wt%CeO29wt%NiO/γ-Al2O3 catalyst with an oxygen permeation flux of 24.71 ml·cm^-2·min^-1 and a high CH4 conversion was obtained in 875 ℃. The resulted high oxygen permeation flux may be due to the added Ce that inhibited the strong interaction between Ni and Al2O3 to form the NiAl2O4 phase. In addition, the introduction of Ce leads up to an important property of storing and releasing oxygen.
基金supported by Major Special Projects of Gansu Province,China(No.21ZD4WA017)University Industry Transformation Promotion Project of Gansu Province,China(No.2020C-11)+1 种基金the Program of“Science and Technology International Cooperation Demonstrative Base of Metal Surface Engineering along the Silk Road”,China(No.2017D01003)the National Natural Science Foundation of China(No.51901093)。
基金The project was supported by the National Natural Science Foundation of China(Grant 50171073).
文摘In order to improve the surface hardness and wear resistance of Ti and Ti alloy components, an oxygen permeation treatment (OPT) was developed. The oxygen permeation behaviors of three Ti alloys, TA2, TB5 and TC11, treated in air with O-P medium at high temperature have been studied. The results show that the 0-P treatment can significantly improve the surface hardness of Ti alloys. The oxidation mass-gain of β-Ti alloy (TB5) is much higher than α-Ti alloy (TA2) under the same condition, while α+β Ti alloy (TC11) is the lowest. All the Ti alloys treated at this condition produce two surface layers: the outer layer consists mainly of TiO2, as well as trace of other oxides, and the inner layer consists of a Ti-O interstitial solid solution formed by the diffusion of oxygen in α crystal lattice. Thick scales of β Ti alloy (TB5) are easily formed depending mainly on the poor solid solution content of oxygen, while deep solution layer can be formed since partial β phase has been transformed into α phase. The scales of α-β Ti alloy (TC11) are very thin and compact. Aluminum-rich zone, as well as deficient zone, is found in oxide layers. A crystallographic characterization of oxygen solution layer has been performed and evaluated by crystallographic lattice constant.
基金supported by the National High-Tech Research and Development Program of China (No. 2006AA11A189)the Research on Novel Technology of Hydrogen Production from Oven Gas from Metallurgy Process (No. 07DZ12036)the National Key Technolo-gies Research and Development Program of China (No. 2006BA103A05)
文摘Perovskite-type oxygen-permeable membrane reactors of BaCo0.7Fe0.2Nb0.1O3-δ （BCFNO） packed with Ru-based catalyst had high oxygen permeability and could be used for hydrogen production by partial oxidation of methane in coke oven gas （COG）. At 1173 K, 94% of methane conversion, 85% of H2 selectivity, 107% of CO selectivity, and as high as 15.4 mL·cm^-2·min^-1 of oxygen permeation flux were obtained. The BCFNO membrane itself had poor catalytic activity to partial oxidation of CH4 in COG. During continuous operation for 70 h at 1173 K, no degradation of the membrane reaction performance was observed. XRD and SEM characterization also demonstrated that the BCFNO membrane reactor exhibited good stability in partial oxidation of methane in COG.
基金supported by the National Natural Science Foundation of China (Nos. 51004069 and 51474145)the National Science Fund for Distinguished Young Scholars (No. 51225401)the Innovation Program of Shanghai Municipal Education Commission and Shanghai University (Nos. 14YZ013 and SDCX2012002)
文摘Dual-phase membranes of 60 wt% Ce0.8Gd0.2O2-δ-40 wt% Pr Ba Co2exFexO3 d（0 x 2） were prepared by a combined citrate and ethylene diamine tetraacetic acid（EDTA） complexing method. X-ray diffraction（XRD）results revealed the good chemical compatibility between ion-conducting phase CGO and electron-conducting phases PBC2 xFxO after sintering in air. The Fe ionic dopant had a significant effect on the phase structure stability and oxygen permeability under CO2 atmosphere, which was confirmed by XRD, thermogravimetrye differential scanning calorimetry（TGeD SC）, scanning electron microscopy（SEM） and oxygen permeation experiments. CGOeP BC0.5F1.5O dual-phase membrane demonstrated a stable oxygen permeation flux of2.71x10-7mol cm 2s 1with 50 mol% He/CO2 as the sweep gas at 925 C, and this value was much higher than that of perovskite-type membranes. The rate-limiting step in the oxygen permeation process changed from the bulk diffusion to the surface oxygen exchange when the CGOeP BC0.5F1.5O membrane thickness decreased to 0.8 mm or less. Due to the high oxygen permeation fluxes and the excellent structural stability under CO2 atmosphere, the CGOeP BC0.5F1.5O membrane is a great potential candidate material for separating oxygen from air in the oxy-fuel combustion techniques.
基金Natural Science Foundation of Guangdong Province (No. 030514)the Science and Technology Program of Guangdong Province(No. 2004B33401006)
文摘Mixed oxygen-ionic and electronic conducting membranes of SrFe（Cu）O3-δ were prepared by solid-state reaction method. The crystal structure, oxygen nonstoichiometry, and phase stability of the materials were studied by TGA and XRD. Oxygen permeation fluxes through these membranes were studied at operating temperature ranging from 750 to 950 ℃. Results showed that doping Cu in SrFeO3-δ compound had a significant effect on the formation of single-phased perovskite structure. For SrFe1-xCu2O3-δ series materials, the oxygen nonstoichiometry and the oxygen permeation flux increased considerably with the increase of Cu-doping content （x = 0.1-0.3）. The sintering property of the membrane decreased significantly when the Cu substitution amount reached 40%. SrFe0.7Cu0.3O3-δ showed high oxygen permeation flux, but SrCuO2 and Sr2Fe2O5 phases formed in the compound after oxygen permeation test induced cracks in the membrane.
文摘Novel mixed conducting oxides, B-site Bi-doped perovskites were exploited and synthesized. Cubic perovskite structures were formed for BaBi0.2COyFe0.8-yO3-δ (y≤0.4) and BaBixCo0.2Fe0.8-xO3-δ (x=0.1 -0.5). The materials exhibited considerable high oxygen permeability at high temperature. The oxygen permeation flux of BaBi0.2Co0.35Fe0.45O3-δmembrane reached about0.77×106 mol/cm2 ·s under an air/helium oxygen partial pressure gradient at 900 ℃, which was much higher than that of other bismuth-contained mixed conducting membranes. The permeation fluxes of the materials increased with the increase of cobalt content, but no apparent simple relationship was found with the bismuth content. The materials also demonstrated excellent reversibility of oxygen adsorption and desorption. Stable time-related oxygen permeation fluxes were found for BaBi0.2Co0.
基金supported by the National Natural Science Foundation of China(51004069)the National Science Fund for Distinguished Young Scholars(51225401)+1 种基金China Postdoctoral Science Foundation(201104254)the Innovation Program of Shanghai Municipal Education Commission and Shanghai University(14YZ013 and SDCX2012002)
文摘Ba0.9R0.1Co0.TFe0.225Ta0.07503-δ （BRCFT, R = Ca, La or Sr） membranes were synthesized by a solid-state reaction. Metal cation Ca2＋, La3＋ or Sr2＋ doping on A-site partially substituted Ba2＋ in BaCoo.TFe0.225Ta0.07503-δ oxides, and its subsequent effects on phase structure stability, oxygen permeability and oxygen desorption were systematically investigated by XRD, TG-DSC, Hz-TPR, O2-TPD techniques and oxygen permeation experiments. The partial substitution with Ca2＋, La3＋ or Sr2＋, whose ionic radii are smaller than that of Ba2＋, succeeded in stabilizing the cubic perovskite structure without formation of impurity phases, as revealed by XRD analysis. Oxygen-involving experi- ments showed that BRCFT with A-site fully occupied by Ba2＋ exhibited good oxygen permeation flux under He flow, reaching about 2.3 mL.min-l .cm-2 at 900 with I mm thickness. Of all the membranes, BLCFT membrane showed better chemical stability in CO2, owing to the reduction in alkalinity of the mixed conductor oxide by La doping. In addition, we also found the stability of the perovskite structure under reducing atmospheres was strengthened by increasing the size of A-site cation （Ba2＋〉La3＋〉SrZ＋〉Ca2＋）.
